Manual McCulloch Li58-26 M40 (page 13 of 320) (All languages)

684137

Zoom out

Zoom in

1/320

regularly hose the grass catcher off with water and

let dry before using.

• Examine the grass catcher frequently for wear or

deterioration. Replace if necessary.

To examine the rear door

The rear door is attached between the rear wheels of

the product. The door decreases the risk of objects that

may be ejected in the direction of the mow position of

the operator.

1. Make sure that the rear door is not damaged.

2. Examine the rear door for defects that push the door

to close, including cracks or broken springs.

3. Replace the rear door or the springs if they are

damaged.

To sharpen and balance the blade

For best results, keep the blade sharp. Replace a bent

or damaged blade.

CAUTION: Use gloves, and/or wind the

blade with a heavy cloth, to prevent damage

to your hands .

1. Sharpen the blade with a file or on a grinding wheel.

Do not sharpen the blade when it is installed on the

product.

CAUTION: We do not recommend that

you sharpen the blade. If you do, make

sure that the blade is balanced. A blade

that is not balanced can cause damage

to the product or motor.

2. Put a straight nail in a piece of wood or a wall. Make

sure you can see 2-3 cm of the nail.

3. Put the center hole of the blade on the head of the

nail. If the blade is balanced, it must stay in a

horizontal position. If one of the two ends of the

blade moves down, sharpen the heavy end until the

blade is balanced.

To replace the blade

1. Lock the blade with a block of wood.(Fig. 55 )

2. Remove the blade bolt.

3. Remove the blade.

4. Examine the blade support and blade bolt to see if

there are damages.

5. Examine the motor shaft to make sure that it is not

bent.

6. When you attach the new blade, point the angled

ends of the blade in the direction of the cutting cover.

(Fig. 56 )

7. Make sure that the blade is aligned with the center of

the motor shaft.

8. Lock the blade with a block of wood. Attach the

spring washer and tighten the bolt and washer with a

torque of Nm.(Fig. 57 )

9. Pull the blade around by hand and make sure that it

turns freely.

WARNING: Use heavy duty gloves. The

blade is very sharp and cuts can easily

occur.

10. Start the product to do a test of the blade. If the

blade is not correctly attached, there is vibration in

the product or the cutting result is unsatisfactory.

Error codes

The error codes help you do troubleshooting on the

product and/or the battery pack while in operation.

LED screen Possible faults Possible steps

No LEDs come on after pressing

the power button on the user con-

trol interface, battery pack does not

function in product

Battery pack not fully put

into product or internal

fuse is blown

Push the battery pack fully into the powerhead un-

til a click is heard. If the LEDs do not illuminate af-

ter the battery pack has been fully put in and the

power button has been pressed on the user con-

trol interface, speak to an approved service cen-

ter.

All four battery capacity LEDs

flash, no other LEDs come on after

pressing the power button

Battery pack not fully put

into product or the internal

temperature of the battery

pack is too hot or too cold.

Push the battery pack fully into the powerhead un-

til a click is heard. If the LEDs continue to flash,

the internal temperature of the battery pack may

be too low or too high. Allow the battery pack to

warm up or cool. To increase the cooling process,

the battery pack can be inserted into the battery

charger to actively cool the battery pack.

778 - 004 - 23.10.2018 13

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Li58-26 M40 in the language / languages: All languages as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Li58-26 M40 Manual

Product: