478445

McCulloch ESV1414 Manual

10
Zoom out
Zoom in
Previous page
1/15
Next page
ENGLISH – 7
case do not tighten the chain immediately after use, but wait until it cools down.
In cases where the loosened chain needs to be adjusted, always unscrew the bar retaining nuts / knob before
adjusting the chain tensioning screw/knob ; adjust the tension and tighten the bar retaining nuts /knob
accordingly.
E. START-UP AND ARREST
1,4,5,6,7,8,9,11,12,13
Start-up: grip both handles firmly, release the chain
brake lever, press and maintain the switch block
pressed in, then press the switch (at this point the
switch block can be released).
Arrest: The machine will stop whenever the switch is
released. In the case where the machine does not
stop, activate the chain brake, disconnect the cable
from the main line socket and take the machine to the
Authorised Service Centre.
F. BAR AND CHAIN LUBRICATION
3,6,7,8,9,12
ATTENTION! Insufficient lubrication will provoke
chain breaking and can cause serious and even
mortal injury.
Bar and chain lubrication is performed by an
automatic pump. If your machine is equipped with an
oil pump adjustment knob (optional) the chain
lubrication can be adjusted as shown in the
illustration (fig.1), according to the type of cutting
operation in hand (dry wood – more oil, green wood -
less oil, long bar- more oil, short bar - less oil).
Take great care to ensure that the chain is always
sufficiently lubricated by never closing the pump
completely. Refer to “Maintenance” for indications on
ensuring that the chain oil is sufficiently distributed.
Choice of chain oil
Always use new oil only (special type for chains) with
adequate viscosity: the oil must adhere well and
guarantee good running properties in both winter and
summer. If chain oil is not available, EP 90
transmission oil can be used.
Never use waste oil because this is this harmful to
health, the machine and the environment. Make sure that
the oil is suitable for the temperature of the environment
where the tool will be used: For temperatures under 0°C
certain oils become denser, overloading the pump and
causing damage. Contact your Authorised Service
Centre for advice on oil choice.
Filling oil tank
Unscrew the oil tank cap, and fill the tank taking care
not to spill any oil (if this occurs clean the machine
carefully) (fig.2), and then screw the cap back on
tightly.
G. MAINTENANCE
1,2,3,4,5,6,7,8,9,12,13
ATTENTION! In cases where work environments are
particularly dirty or dusty, the operations described
must be performed more frequently than mentioned
in the instructions.
Before each use
Control that the chain oil pump functions correctly:
direct the bar towards a clear surface at a distance of
about 20 centimetres; after the machine has run for
about a minute, the surface should show clear traces
of oil(fig.1).
Check that excessive strength is not needed for
activating and deactivating the chain brake. Also
check that it is not activated too easily and that it is
not blocked. Then check chain brake function as
follows: release the chain brake, grip the machine
correctly and start up the machine, activate the chain
brake by pushing the front hand guard forward with
the left wrist or arm but without removing the hand
from the handle(fig.2). If the chain brake is working
correctly, the chain should be blocked immediately.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch ESV1414 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch ESV1414 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info