684233
7
Zoom out
Zoom in
Previous page
1/536
Next page
Turning the screw will move the adjusting pin up and
down the screw. Locate this adjusting pin before you
begin mounting the bar onto the saw. See following
illustration.
1. Turn the adjusting screw by hand counterclockwise
until the adjusting pin is positioned between the
LQGLFDWRUPDUNV%RQWKHFOXWFKFRYHU7KLV
should allow the adjusting pin to be near the
correct position.
2. Slide guide bar with chain on bar bolts until guide
bar stops against clutch drum sprocket. Cutters
must face in the direction of rotation.
3. &KHFNWKDWWKHGULYHOLQNVRIWKHFKDLQ¿WFRUUHFWO\
on the drive sprocket and that the chain is in the
groove on the bar.
4. Fit the clutch cover and insert the adjusting pin in
the cut-out in the bar.
5. 7LJKWHQWKHEDUQXW¿QJHUWLJKW
TENSIONING THE CHAIN
(Including units with chain already installed)
a WARNING: If the saw is operated with
a loose chain, the chain could jump off
the guide bar and result in serious injury
to the operator and/or damage the chain
making it unusable. If the chain jumps off
the guide bar, inspect each drive link for
damage. Damaged chain must be repaired
or replaced.
Chain tension is very important. Chains stretch during
XVH7KLVLVHVSHFLDOO\WUXHGXULQJWKH¿UVWIHZWLPHV
you use your saw. Always check chain tension each
time before you start the chain saw.
:KHQ¿WWLQJDQHZFKDLQWKHFKDLQWHQVLRQKDVWREH
FKHFNHGIUHTXHQWO\XQWLOWKHFKDLQLVUXQLQ
A correctly tensioned chain ensures good cutting
performance and long life.
CHECKING THE TENSION
Use the screwdriver end of the chain adjustment tool
EDUWRROWRPRYHFKDLQDURXQGJXLGHEDU,IWKHFKDLQ
does not rotate, it is too tight. If the chain is too loose,
it will sag below the bar.
NOTE: The chain is tensioned correctly when
the weight of the chain does not cause it to sag
below the guide bar (with the chain saw sitting in
DQXSULJKWSRVLWLRQEXWWKHFKDLQVWLOOPRYHVIUHHO\
around the guide bar.
ADJUSTING THE TENSION
1. /RRVHQEDUQXWVXQWLOWKH\DUH¿QJHUWLJKWDJDLQVW
the clutch cover.
NOTE: When adjusting chain tension, make sure
WKHEDUQXWVDUH¿QJHUWLJKWRQO\$WWHPSWLQJWR
tension the chain when the bar nuts are tight can
cause damage.
2. Turn adjustment screw clockwise until chain solidly
contacts bottom of guide bar rail.
Chain tensioning—side adjust models:
Chain tensioning—front adjust models:
3. Hold up the bar tip and tighten the bar nuts with
the combination tool.
7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch CS 42S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CS 42S in the language / languages: All languages as an attachment in your email.

The manual is 20,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info