Manual McCulloch Cabrio 433L (page 13 of 21) (English, German, French, Spanish)

478383

Zoom out

Zoom in

1/21

S Cut only f rom your l eft to your r ight. Cutting on

right side of the shield will throw debris away

from the operator.

S Use the shoulder strap and keep a firm grip

on the unit with both hands. A properly

adjusted shoulder strap will support the

weight of the u nit, freeing y our arms and

hands to control and guide the cutting motion.

S Keep feet comfortably spread a part and

braced for a possible sudden, rapid thrust of

unit. Do not overreach. Keep firm footing and

balance.

S Keep blade below waist level; it will be

easier to maintain control of unit.

S Do not raise theengine above your waist as

the blade can come dangerously close to

your body.

S Do not swing unit with such force that you

are in danger of losing your balance.

Bring the engine to cutting speed before enter-

ing the material to be cut. If the blade does not

turn when you squeeze the throttle t rigger, make

sure shaft is fully inserted into the engine.

Always release the throttle trigger and allow

engine to return to idle speed when not cut-

ting. The blade should not turn while the en -

gine is running at idle. If the blade turns a tidle,

do not use your unit . Refer to the CARBURE-

TOR ADJUSTMENT section or contact your

authorized service dealer .

S Maintain good firm footing while using the

unit. Do this by planting feet firmly in a

comfortable apart position.

S Cut while swinging the upper part of your

body from left to right.

S Asyoumoveforwardtothenextareatocut,

be sure to maint ain your balance and footing.

Cut using the 2

o’clock t o 4 o’clock

position of the

blade

2 o’clock

4 o’clock

RECOMMENDED CUTTING POSITION

WARNING: The operator or others

must not try to clear away cut material with the

engine running or the blade turning to avoid

serious injury . Stop engine and blade before

removing m aterials wrapped around blade or

shaft.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

WARNING: For each optionalattach-

ment used, read entire instruction manual be-

fore use and follow all warnings and in-

structions in manual and on attachment.

WARNING: Ensure handlebar is

installed when using edger or brushcutter at-

tachments. Attach handlebar above arrow on

safety label on t he upper shaft (engine end of

unit). If your edger or brushcutter attachment

does not include a handlebar , a handlebar ac-

cessory kit (#530071451) is available from

your authorized service dealer.

Handlebar

EDGER SAF ET Y

WARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, etc.) which

can be thrown by the blade or can wrap

around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released. The blade

can seriously cut you or others. Allow blade to

stop before removing it from the cut.

S Throw away blades that are bent, warped,

cracked, broken or damaged in any o ther

way. Replace parts that are cracked, chipped,

or damaged before using the unit.

S Do not attempt to remove cut material nor

hold material to be cut when the engine is

running or when cutting blade is moving.

S Always keep the wheel and depth adjusting

skid in contact with the ground.

S Always push the unit slowly over the ground.

Stay alert for uneven sidewalks, holes in the

terrain, large roots, etc.

S Always use the handlebar when using edger

attachmen t.

BLOWER/VACUUM S AF ET Y

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects

such as rocks, glass, wire, e tc. that can rico-

chet, be thrown, or otherwise cause injury or

damage during operation.

S Do not set unit on any surface except a clean,

hard area while engine is running. Debris

such as gravel, sand, dust, grass, etc., could

be picked up by the air intake and thrown out

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Cabrio 433L in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Cabrio 433L Manual

Product: