684239
7
Zoom out
Zoom in
Previous page
1/27
Next page
English--- 7
115430026 Rev. 4 2/17/12
GENERAL SAFETY PRECAUTIONS
Stop switch
Make sure the engine stops when you push
and hold the stop switch.
Cutting attachment guard
This guard is intended to prevent loose
objects from being thrown towards the
operator. The guard also protects the
operator from accidental contact with the
cutting attachment.
Check that the guard is undamaged and not
cracked. Replace the guard if it has been
exposed to impact or is cracked.
Always use the recommended guard for the
cutting attachment you are using. See the
“Technical data” section.
W ARNING: Never use a cutting
attachme nt without an approve d
guard. See the section on “T echnical
data”. If an incorrect or faulty guard
is fitted this can cause serious
personal injury .
W ARNING: Overexposure to
vibration can lead to circulatory
damage or nerve damage in people
who have impaired circulation.
Contact your doctor if you experi-
ence symptoms of overexposure to
vibration. Such symptoms include
numbness , loss of feeling, tingling,
pricking, pain, loss of strength,
changes in skin color or condition.
These symptom s normally appear
in the fingers, hands or wrists. The
risk increases at low temperatures.
Muffler
The muffler is designed to reduce the noise
level and to direct the exhaust gases away
from the operator.
CAUTION! Muf fler is fitted with a catalytic
converter designed to reduce exhaust gas
emissions.
Harness quick release
There is an easily accessible, harness
quick release fitted at the front in case of an
emergency that requires you to free your-
self from the machine and harness.
See instructions under the heading Adjust-
ing the harness.
Check that the harness straps are correctly
positioned. Once the harness and machine
have been adjusted, check that the harness
quick release works correctly.
Use of incorrectly wound trimmer line or an
incorrect cutting attachment increases the
level of vibration.
See instructions under the heading Start.
Start the machine and apply full throttle.
Release the throttle and check that the cut-
ting attachment stops and remains at a
standstill. If the cutting attachment rotates
with the throttle in the idle position then the
carburettor idle setting must be checked. See
instructions under the heading Maintenance.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch B28 B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch B28 B in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info