782193

MCAllister MSSP120 Manual

20
Zoom out
Zoom in
Previous page
1/116
Next page
20
GB MSSP120
Getting started...
Safety
–Do not remove any cutting residues or other parts of workpieces from the
cutting zone while the machine is running and the saw unit is not at rest.
–Support long workpieces (e.g. with a roller table) to prevent them sag-
ging at the end of a cut.
–In an emergency, switch off the machine directly and pull out the pow-
er plug.
–Follow all these instructions before and while you are working with the
saw. Keep these instructions in a safe place.
–Give these safety regulations to all persons who work on the machine.
–Do not use this saw to cut re wood.
–Never use the saw to cross -cut round timber unless it is equipped with
a suitable holding device.
–The machine is equipped with a safety switch to prevent it being
switched on again accidentally after a power failure.
–Provide good lighting
–After you have switched off the motor, never slow down the saw blade
by applying pressure to its side.
–Faulty saw blades have to be replaced immediately.
–Never use saw blades which do not comply with the data specied in
this manual.
–Never dismantle the machines safety devices or put them out of oper-
ation.
–Never cut workpieces which are too small to hold securely in your
hand.
–Never load the machine so much that it cuts out.
–It is imperative to observe the manufactureres safety, operating and
maintenance instructions as well as the dimensions quoted in the
technical data.
–It is imperative to observe the accident prevention regulations in force
in your area as well as all other generally recognized rules of safety.
–The machine is designed for indoor installation only.
–Workpieces smaller than the blade guard may lead to injuries to your
hands and ngers. Use suitable aids!
–Always insert the blade so that the teeth point down toward the table.
–To avoid broken blades, always set the correct blade tension.
–Be particularly careful when sawing material with irregular cutting
proles.
–Take special care when cutting round workpieces such as rods or
tubes as they may roll away from the blade and cause the teeth to jam.
Secure such workpieces with a wedge.
–When you withdraw the workpiece the teeth may get caught in the
kerf, particularly if the gap is blocked by sawdust. If this happens you
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCAllister MSSP120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCAllister MSSP120 in the language / languages: English, German, French as an attachment in your email.

The manual is 4.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info