168654

MB Quart pab 1200 1 d Manual

3
Zoom out
Zoom in
Previous page
1/88
Next page
3
English
System design
GENERAL INSTALLATION NOTES
Installation
The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup.
This section is intended to assist the installer by offering several tips and hints about good installation practice. Please remember that any
system is only as good as its weakest link.
Determine the system format, e.g., single amplifi er, active, front/rear and so on. Then choose the amplifi er power points according to personal
taste. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom
capability, to reproduce musical peaks cleanly without distortion. Lower power amplifi ers will clip earlier than their more powerful cousins, and
cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils.
Choose loudspeaker and amplifi er mounting locations. Loudspeaker location is always a matter of compromise between space and sound stage
imaging. Amplifi ers should be mounted with the fi ns running vertically for best convection cooling, to minimize overheating.
Purchase the best quality RCA cables you can afford, for reliability and less engine noise interference in the audio system.
General:
Mount the amplifi er/s in the chosen location.
Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle
that can cause electrical noise, such as fuel pumps.
Power and ground connections:
Use a suffi cient gauge power cable, at least #8 per amplifi er. In a multi amplifi er system, it is advisable to mount a large enough fuse right at the
battery, and run a master +12 volt power cable to a fused distribution block near the amplifi ers. It is then a simple matter to connect the +12 volt
terminal of each amplifi er to the distribution block.
Ground each amplifi er with as short a ground lead, again at least #8 gauge, directly to the vehicle chassis. Use a ground distribution block, if you
wish, but it is extremely important to keep the main ground lead from this distribution block to the chassis as short as possible , not more than 12“.
The ground connection integrity to the chassis is very important, and the best way to achieve a good, solid electrical and mechanical contact is to
use a large round crimp lug, crimped and soldered to the ground cable. The next step is to scrape the paint off the vehicle chassis, slightly larger
than the ground lug, at the connection point. Drill a clearance hole in the chassis, the same size as the lug hole, and use a bolt, spring washer and
nut to securely fasten the ground lug. Use petroleum jelly to coat the bolt/lug connection, to prevent oxidization with time.
TIP:
Use the same approach when installing head units, equalizers or any audio equipment for that matter - run short individual grounds from each
piece directly to the vehicle chassis, to minimize ground loops and system noise.
All power, ground and speaker connections should be crimped and soldered for reliability. Make sure that none of the cable insulation can chafe
against exposed metal in the vehicle, causing short circuits to the chassis.
Safe connection sequence:
After all cables are run, connect speaker wires to the speakers and amplifi ers, then run and plug in RCA cables. Next, connect all power grounds
and remote turn on leads. Now connect all +12 volt cables to the amplifi er/s and distribution blocks and fuse holders. Finally, connect the main
+12 volt cable to the battery, with the main fuse removed, and we are almost ready to power up the system.
Power up the system:
The following procedure may seem like overkill, but there is nothing more frustrating than turning on a system for the fi rst time, and it does not
work properly immediately.
First, make sure the head unit is off, and turn all level controls to minimum (anticlockwise), including the head unit volume control. Set all equa-
lizers to 0 dB (no boost), and all crossover frequency controls at approximate frequencies, as recommended by the loudspeaker manufacturer. Set
all input selector and crossover switches as required for the application.
Remove all amplifi er fuses, and insert the main fuse at the battery. If the fuse does not blow, you can insert the fuse in one of the amplifi ers, and
we are ready to turn on the system.
Turn the head unit on, insert a CD, or select a radio station, and increase the head unit volume control. If the system sounds fi ne, turn off the head
unit, and install fuses in the remaining amplifi ers, one by one, till the complete system is powered up and functioning properly.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MB Quart pab 1200 1 d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MB Quart pab 1200 1 d in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 11,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info