INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT. All LINE INPUT jacks must be connected (CH1/CH2/CH3/CH4).
Therefor you need to use two Y-connectors to splice the audio signal. If a separate SUB OUT from your headunit is available, use this
as LINE OUT.
• Connect the subwoofers with the SPEAKER OUTPUTS CH1/2 + BRIDGED - and CH3/4 + BRIDGED -.
• Ensure by any means, that the total impedance load of all subwoofers per channelpair is not lower than 4 ohms. Too low impedance
cause high temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
CROSSOVER SETTINGS CH1/2 & CH3/4 (SUBWOOFER 1 & SUBWOOFER 2)
• In the mono/subwoofer mode the X-OVER switch must set to the LP/BP position (Lowpass/Bandpass mode), thereby the higher
frequencies will be eliminated. The cut-off frequency ist adjustable with the LOW PASS controller and should be set between
60 to 100 Hz, depending on the size of the subwoofer.
• In the lowpass mode (LP/BP) the HIGH PASS controller works also as subsonicfilter, that eliminates the ultra-low, not hearable and
harmful frequencies to generate a bandpass signal (Bandpass mode). The subsonic frequency should be set between 15 to 40 Hz,
depending on the size of the subwoofer. NOTE: If this value is higher than the lowpass setting, no sound is hearable.
LEVEL CONTROLLER CH1/2 & CH3/4 (SUBWOOFER 1 & SUBWOOFER 2)
• Turn the INPUT LEVEL controller of the amplifier to the 6V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the INPUT LEVEL controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER CH1/2 & CH3/4 (SUBWOOFER 1 & SUBWOOFER 2)
• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
26
SPE AKER OU TPUT
CH1 CH2 CH3 CH4
BRI DGED BRIDG ED
POW ER INP UT
GND REM
FUS E
12V
POW ER
PRO TECT
CH1 /CH2
CH3 /CH4
LOW PASS
BASS BOOST
INPU T LEVELHIGH PASS
X-OV ER
LP/ BP FUL L
HP
LOW PASS
BASS BOOST
INPU T LEVELHIGH PASS
X-OV ER
LP/ BP FUL L
HP
LIN E INPUT OUT PUT
R
L
CH1 CH3
CH2 CH4
30H z 150Hz
0dB 12d B
6V 0 .2V10H z 150 Hz
30H z 150Hz
0dB 12d B
6V 0 .2V10H z 150 Hz
Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of
the amplifier by using two Y-connectors
Subwoofer 1
4 – 8 Ohms
L R
Switch position LP/BP
Switch position
LP/BP
Y-Connectors
Subwoofer 2
4 – 8 Ohms
I N T E R C O N N E C T I O N E X A M P L E S
NSC475