168726
13
Zoom out
Zoom in
Previous page
1/16
Next page
ENG
M O N O - A M P L I F I E R S
DSC1500.1D
FEATURES:
• PROTECTION and POWER LED indicators
• The REMOTE jack enables a dash mount control for the BASS BOOST
• BALANCED INPUT: balanced MINI-DIN signal input
NOTE: DO not use this input with the RCA input at the same time.
• LOW PASS: Variable from 35Hz to 250Hz
• SUBSONIC FILTER: Variable from 15Hz to 35Hz
• PHASE: Variable from 0 to 180
• BASS BOOST: 45Hz bass boost from 0dB to 9dB
• INPUT LEVEL sensitivities are variable from 0.2volts to 6volts
• Each model is capable of 1ohm minimum
3. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack and control the
Bass Boost setting.
4. Mode-Switch:
The „MODE“ switch must be on „MASTER OUTPUT“ position.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than 1ohm.
1. Interconnect cable checklist:
Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source.
IMPORTANT: Do not connect the Left and Right stereo signals
together to achieve a mono signal as this will damage the output
stage of source and possibly the input stage of the amplifier.
- Use at least 1,5 sqmmspeaker wiring. These amplifiers feature dual speaker
terminals, simplifying the hookup of multiple speakers.
STANDARD OPERATION
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
MONO
LINE INPUT
BASS-REMOTE
SUBWOOFER
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
SUBWOOFER
WITH DUAL-
VOICE COIL
4. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack of the „MASTER“ amp
and control the Bass Boost setting of both amps together.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than 2ohm.
Check the below featured connection figures.
1. Interconnect cable checklist MASTER:
Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source into the „MASTER“ amp.
2. Interconnect cable checklist SLAVE:
Connect a mono line cable from „MASTER OUTPUT “ of the „MASTER“ amp
with the „SLAVE INPUT “ of the „SLAVE“ amp.
3. Mode Switch:
The „MODE“ switch of the „MASTER“ amp must be in position „MASTER OUTPUT“.
The switch of the „SLAVE“ amp in position „SLAVE INPUT“.
MASTER/SLAVE OPERATION
Amplifiers can run at a 2 ohm load
minimum when linked.
2 SUBWOOFERS
WITH SINGLE-
VOICE COIL
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
MONO
LINE INPUT
BASS-REMOTE
BRIDGING
JUMPER CABLE
MASTER TO SLAVE
RCA JUMPER
CABLE
INVERT POLARITY
ON VOICE COIL 2
INVERT POLARITY
ON SUBWOOFER 2
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MB Quart dsc500 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MB Quart dsc500 1 in the language / languages: English, German as an attachment in your email.

The manual is 6,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info