506516

Maytag MDG22PD Manual

16
Zoom out
Zoom in
Previous page
1/64
Next page
16
CODE EXPLANATION
COIN SLIDE OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
Replacement of metercase will be needed for coin slide mounting.
Not Selected ‘OFF’.
Selected ‘ON’.
NOTE: This option needs to be set to ‘00’ unless the
metercase has been changed to accept a coin slide device.
Press DELICATES button 3 consecutive times for this
selection. When coin slide mode is selected, set ‘b.’ equal to
value of slide in coins. Set ‘6 xx’ (REGULAR CYCLE PRICE)
and ‘3.xx’ (SPECIAL CYCLE PRICE) to number of slide
operations. 6 01 & 3.01 = 1 slide push.
NOTE: If the installer sets up ‘CS’ on a coin drop model,
it will not register coins.
Press PERM. PRESS button once to advance to next code.
ADD COINS OPTION
This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’.
This option causes the customer display to show the number
of coins (coin 1) to enter, rather than the amount.
Not Selected ‘OFF’.
Selected ‘ON’.
Press DELICATES button 3 consecutive times for this selection.
PN MODELS: This option is not selectable.
Press PERM. PRESS button once to advance to next code.
COIN/DEBIT OPTION
Both coin & debit selected. (NOT AVAILABLE)
Coins selected, debit disabled.
Press DELICATES button 3 consecutive times for this selection.
Debit Card selected, coin disabled. Default for PN models,
and for PN operation, must be set as J._d.
Press DELICATES button 3 consecutive times for this selection.
Enhanced Debit is self-selected when a Generation 2 card
reader is installed in the dryer. The ‘Ed’ option cannot be
manually selected or deselected. (NOT AVAILABLE)
Press PERM. PRESS button once to advance to next code.
PRICE SUPPRESSION OPTION
This option is either SELECTED ‘ON’ OR NOT SELECTED ‘OFF’.
This option causes the customer display to show ‘AVAILABLE’
or ‘ADD’ rather than the amount of money to add. (Used
mainly in debit installations.)
Not Selected ‘OFF’.
Selected ‘ON’. Press DELICATES button once for this selection.
Press PERM. PRESS button once to advance to next code.
CLEAR ESCROW OPTION
This option is either SELECTED ‘ON’ OR NOT SELECTED ‘OFF’.
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
Selected ‘ON’.
Not Selected ‘OFF’. Press DELICATES button once to deselect
this option.
Press PERM. PRESS button once to advance to next code.
HUNDREDTH INCREMENT OFFSET
This represents the hundredth increment price offset used
in Generation 2 (Enhanced Debit) PN models set up with card
reader. Choose from 0-4 hundredths by pressing the WHITES
AND COLORS button. (NOT AVAILABLE)
Press PERM. PRESS button once to advance to next code.
8.0 0
E
. 0 0
E
. 0 0
E
.
AC
8.0 0
8.
CS
J
.
C
8
L
. 0 0
L
. 0 0
L
.
PS
J
.
C
8
J
.
C
8
J
.
C
8
J
.
E
8
8.
CE
8.
CE
8.0 0
0. 0 0
0. 0 0
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number of cycles in HUNDREDS. 1 02
= 200
2 00 Represents the number of cycles in ONES. 2 25 = 225
TOTAL CYCLES = 225
This is ‘VIEW ONLY’ and cannot be cleared.
Press the PERM. PRESS button once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is true:
3 00 Currency amount in HUNDREDS. 3 01
= 100.00
4 00 Currency amount in ONES. 4 68
= 168.00
5 00 Currency amount in HUNDREDTHS. 5 75 = 100.75
TOTAL = 168.75
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
■
PD MODELS: Reinstall access door.
■
PN MODELS where AA1 plug was removed:
1. Unplug dryer or disconnect power.
2. Open console, reinsert jumper into AA1, close console.
3. Plug in dryer or reconnect power.
■
PN WITH PROGRAMMING SWITCH: Turn key clockwise and
remove.
■
If Service Access Code was used to enter set-up mode: From
Set-up Code 8, press button #1 for 4 seconds, wait 2 minutes
without touching any buttons (without diagnostic modes running),
or power down the dryer, then reapply power.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maytag MDG22PD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maytag MDG22PD in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info