817896
2
Zoom out
Zoom in
Previous page
1/12
Next page
5
showing (+) must be connected to the vehicle 12 volt (+)
positive supply.
STEP 4
Conrm the 4 metal mounting clips are rmly in place on
the Roof Receiving Flange. With the MAXXFAN open
and the exhaust/intake louvers facing the rear of the
vehicle, lower the MAXXFAN onto the Roof Receiving
Flange.
Make sure the power wires slide to the vehicle interior
and do not become entangled on the Roof Receiving
Flange’s upward edge.
STEP 5
Verify the MAXXFAN is fully seated down on the Roof
Receiving Flange and fasten the MAXXFAN to the Roof
Receiving Flange using the four 3/4” #10 stainless steel
screws provided.
CAUTION: Only use the screws provided/specied
for this installation or internal damage and/or insecure
mounting may result.
STEP 1
MAXXFAN requires a roof opening of 14” x 14”. If you
are replacing another type already installed, remove the
old existing roof vent. Remove all old roof sealant for a
minimum of 2” entirely around the roof opening.
Place the MAXXFAN Roof Receiving Flange (reference
photo #2 below) into the roof opening and trace a pencil
line around it to verify the clean seal area that will be
required. Note that the Roof Receiving Flange must be
centered in the roof opening with the metal clips facing
the sides of the vehicle (not facing the front or rear of the
vehicle).
CAUTION: When installing your Roof Flange, only
use a caulking/sealant compatible with the ange
(plastic product) and the roof surface. DO NOT
use materials containing solvents such as or similar
to Xylene, Toluene, Methyl Ethyl Ketone, Acetate
or Acetone as they can damage the ange. Also,
Polysulde (Thiokol) type sealants must be avoided.
Silicone Sealants such as G.E. Silicone II (non-
paintable) used for outdoor applications have proven
to be suitable for this installation.
If in doubt, please contact the manufacturer of your
RV for further information.
STEP 2
Apply Sealant or Caulking within the area you have traced
on the roof with a pencil. Apply it carefully to avoid gaps
that may allow water to enter.
Fasten the Roof Receiving Flange to the roof with
screws provided.
Apply additional roof sealant over the screw heads and
around the edge of the roof ange.
CAUTION: Disconnect main vehicle power before
connecting 12 volt DC power to the MAXXFAN!
NOTE: The MAXXFAN must be fully opened prior to
proceeding to STEP 3. Turn knob to fully raise the vent
lid.
NOTE: On the NON-REMOTE controlled models, the
knob must be pulled out to unlock before turning.
STEP 3
Using the insulated electrical connectors provided,
connect the vehicle’s 12 volt power to the two
MAXXFAN power wires located on the driver side of
the MAXXFAN.
NOTE: The MAXXFAN black wire identied with a tag
THIS COMPLETES THE ROOF TOP
PORTION OF THE INSTALLATION
NOTE: Re-apply 12 volt vehicle power. The MAXXFAN,
excluding the 5301K and 6401K, will emit a beeping sound
to indicate power is properly connected. In addition, the
Remote Control model will automatically close the vent cover.
If the MAXXFAN does not beep when power is connected,
go back to step #3. Conrm that proper connections were
made and 12 volt power is on and available. This MAXXFAN
incorporates a self-resetting fuse on the circuit board located
in the ceiling assembly. It can be reset by removing and re-
applying power. If your fan fails to operate or needs reset,
contact Customer Service at 316.832.4357 for assistance or
solicit the aid of an electrical technician.
RECEIVING FLANGE
UPPER EDGE
METAL MOUNTING
CLIPS
4
INSTALLATION INSTRUCTIONS - ALL MODELS
OPEN / CLOSE
KNOB
ROOF FLANGE
2
2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MaXxVan MaXxvan de luxe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MaXxVan MaXxvan de luxe in the language / languages: English as an attachment in your email.

The manual is 0.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info