Step 1 "CLEANSE"
Step 2 "MOISTURISE"
Step 3 "BOOST" (milky lotion)
Standard daily treatment. Fine vibration in “BOOST” mode and gentle switching of the
electrode will enhance the moisturizing effect of lotion
.
Daily treatment (Required time: approximate 15 minutes)
Weekly treatment (Required time: approximate 15 minutes)
2. Press the power switch.
(Fig. 6)
3 Choose "the strength" of electrical potential with the Level switch button.
Switch the "strength" with the level switch button according to the
condition of your skin.
The level indicator lamp will be turned on, and "CLEANSE" on
the mode indicator lamp will start flashing. If a lamp in another
mode is flashing, press the mode switch button to switch to "CLEANSE.”
Every time the level indicator button is pressed, the high, medium, and low of the
electrical potential will be switched. There will be no change in vibration strength.
The memory function memorizes the "strength" when the power has been shut off.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "Low."
Make sure to hold the body with your hand touching the back plate.
5 Apply cotton to the skin and move the device slowly.
(Fig. 8)
Apply the cotton gently to the face and slowly move the device by sliding it from the
center of the face to the outer side.
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
The time for use is within approximate 5 minutes.
Unless you apply the cotton to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the head is not vibrating, the device is not working.
If you leave the device as it is for about 5 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
4 Hold the device with your hand touching the back plate of the body.
(Fig. 7)
Add more toner when there is no moisture in the cotton or when the device is
difficult to slide.
Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the level
switch button and switch to "Low."
If you still feel your skin tingling, use the device by adding more toner.
How to use
CAUTION
Step 1 "CLEANSE"
This mode removes fine residue remaining in pores which cannot be removed by just
washing.
1. Saturate cotton attached to the body with toner after washing your face.
Please use your regular toner or rubbing-off toner with an exfoliating effect.
(Do not use milky lotion or a gel-like or thick toner.)
Saturate the cotton with toner to the extent that toner permeates the back of the
cotton.
7 Remove the ring and the cotton.
6 After 5 minutes have elapsed, the device will automatically shut off. (Auto shutoff function)
The finish sound (beep beep) will inform you.
Wipe off the surface of the head with a tissue.
Do not use the cotton again once it is used. It might cause problems with your skin.
1 Attach new cotton to the body with the attachment ring.
Step 2 "MOISTURISE"
This mode cares for skin by allowing moisturizing ingredients of toner to permeate the skin.
When using cotton
For attaching cotton, see “Preparation before use”.
Step 1 "CLEANSE"
Step 2 "MOISTURISE"
Step 3 "BOOST" (use of sheet mask)
Care for the skin thoroughly once or twice a week in “BOOST” mode using a
commercially available sheet mask.
Do not use the product around eyes and ears.
(Cause of accidents or bad physical condition)
If you feel something is unusual with your skin or body while using the
device, stop using it immediately and consult a skin care specialist.
(Cause of accident or poor health)
Some toner (just with mineral spring or water) may be difficult to bring out a
good effect.
Do not keep the cotton on the same area of skin, but move it
around. (Cause of problems with your skin or poor health.)
3 Press the power switch. (Fig. 9)
The level indicator lamp will be turned on, and the "MOISTURISE" on the mode
indicator lamp will start flashing. When a lamp in another mode is flashing, press
the mode switch button and switch the mode.
Saturate the cotton with lotion to the extent that lotion permeates the back of the
cotton.
2 Saturate the cotton with your regular toner.
4 Choose "the strength" of electrical potential with the level switch button.
Switch the "strength" with the Level switch button according to the condition of your skin.
Every time the level switch button is pressed, the “LOW”,”MEDIUM” and “HIGH” in
the electrical potential will be switched.
There will be no change in vibration strength. The memory function memorizes the
"strength" when the power has been shut off.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "LOW."
When the "CLEANSE" mode is finished, press the power switch
and the "MOISTURISE" mode will automatically be set.
Do not use milky lotion or gel-like or thick toner.
