171513
15
Zoom out
Zoom in
Previous page
1/45
Next page
15MAXDATA Server PLATINUM 3200 I M6
3 Setting up the Chassis
This chapter describes how to set up your server chassis for the first time.
Tools and Supplies Needed
Phillips (cross head) screwdriver (#2 bit)
Small flat-head screwdriver
Anti-static wrist strap (recommended)
Safety: Before You Remove the Access Cover
Before removing the access cover for any reason, observe these safety guidelines:
Turn off all peripheral devices connected to the server.
Turn off the server by pressing the power button on the front of the chassis. Then unplug the
AC power cord(s) from the chassis or wall outlet.
Label and disconnect all peripheral cables and all telecommunication lines connected to I/O
connectors or ports on the back of the chassis.
Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap
attached to chassis ground – any unpainted metal surface – when handling components.
Warnings and Cautions
These warnings and cautions apply whenever you remove the access cover(s) to access components
inside the server. Only a technically qualified person should integrate and configure the server.
WARNINGS
The power button on the front panel DOES NOT turn off the AC power. To remove power from server,
you must unplug the AC power cord(s) from the wall outlet or the chassis.
Hazardous electrical conditions may be present on power, telephone, and communication cables.
Turn off the server and disconnect the power cord(s), telecommunications systems, networks, and
modems attached to the server before opening it. Otherwise, personal injury or equipment damage
can result.
Hazardous voltage, current, and energy levels are present inside the power supply. There are no user-
serviceable parts inside it; servicing should be done by technically qualified personnel.
CAUTIONS
ESD can damage disk drives, boards, and other parts. Perform all procedures in this chapter only at
an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic
wrist strap attached to chassis ground any unpainted metal surface on your server when handling
parts.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their
edges. Do not touch the connector contacts. After removing a board from its protective wrapper or
from the server, place the board component side up on a grounded, static free surface. If you place
the server board on a conductive surface, the battery leads may short out. If they do, this will result
in a loss of CMOS data and will drain the battery. Use a conductive foam pad if available. Do not slide
board over any surface.
For proper cooling and airflow, always install the access cover before turning on the server. Operating
it without the cover in place can damage system parts.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata platinum 3200 i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata platinum 3200 i in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info