Manual Maxdata M-book 6000 (page 200 of 202) (English)

463998

200

Zoom out

Zoom in

1/202

V10.1.10

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information

contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or

any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear

in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)

of this publication.

This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans-

mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators

of this publication, except for copies kept by the user for backup purposes.

Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade-

marks of their respective companies. They are mentioned for identification purposes only and are not intended

as an endorsement of that product or its manufacturer.

©July 2010

Trademarks

Intel, Celeron and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc-

tive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux-

embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,

United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov-

enia.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference.

And

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator

and your body.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex-

pressly approved by the manufacturer for compliance with the above standards could void your authority to operate the

equipment.

If your purchase option includes both Wireless LAN and 3.75G modules, then the appropriate antennas will be installed.

Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate

in conjunction with any other antenna or transmitter.

Important Notice - 3.75G/HSPA & Bluetooth/Wireless LAN Modules

In order to comply with FCC regulations you should NOT operate the 3.75G/HSPA module and the Bluetooth/Wireless LAN

modules at the same time as this may disrupt radio frequency, and cause interference. When the 3.75G/HSPA module is

powered on, make sure that the Bluetooth/Wireless LAN modules are powered off.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury

to persons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC

Output of 19V, 3.42A (65 Watts) or 18.5V, 3.5A (65 Watts) minimum AC/DC Adapter.

CAUTION

Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.

TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER, TELE-

COMMUNICATION LINE CORD

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam-

aged.

Do not expose the computer

to any shock or vibration.

Do not place it on an unstable

surface.

Do not place anything heavy

on the computer.

Do not expose it to excessive

heat or direct sunlight.

Do not leave it in a place

where foreign matter or mois-

ture may affect the system.

Don’t use or store the com-

puter in a humid environment.

Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

5. Take care when using peripheral devices.

Do not turn off the power

until you properly shut down

all programs.

Do not turn off any peripheral

devices when the computer is

on.

Do not disassemble the com-

puter by yourself.

Perform routine maintenance

on your computer.

Use only approved brands of

peripherals.

Unplug the power cord before

attaching peripheral devices.

VIII

Preface

Power Safety

The computer has specific power requirements:

•Only use a power adapter approved for use with this computer.

•Your AC/DC adapter may be designed for international travel but it still requires a steady,

uninterrupted power supply. If you are unsure of your local power specifications, consult

your service representative or local power company.

•The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong

is an important safety feature; do not defeat its purpose. If you do not have access to a com-

patible outlet, have a qualified electrician install one.

•When you want to unplug the power cord, be sure to disconnect it by the plug head, not by

its wire.

•Make sure the socket and any extension cord(s) you use can support the total current load

of all the connected devices.

•Before cleaning the computer, make sure it is disconnected from any external power sup-

plies (i.e. AC/DC adapter or car adapter).

Do not plug in the power

cord if you are wet.

Do not use the power cord if

it is broken.

Do not place heavy objects

on the power cord.



Power Safety

Warning

Before you undertake

any upgrade proce-

dures, make sure that

you have turned off the

power, and discon-

nected all peripherals

and cables (including

telephone lines). It is

advisable to also re-

move your battery in

order to prevent acci-

dentally turning the

machine on.

Preface

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly

result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qual-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,

under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with

your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the

manufacturer. Discard used battery according to the manufacturer’s instructions.

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.

Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the

computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the

power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and

screw(s) before turning the computer on.

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard-

ware and software. Make sure your documents are prepared.



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a

notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prevent your

computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.

XII

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,

keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very

common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knock-

ing the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com-

puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and

disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:

Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.

These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make

sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)

charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.

Wait a few minutes before turning it on so that any moisture can evaporate.

XIII

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods of time.

Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or

other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the

level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on

a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles

when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent

and short breaks are better than fewer and longer breaks.

XIV

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and

shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for

an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

Preface

Contents

Notice .................................................................................I

FCC Statement ................................................................III

FCC RF Radiation Exposure Statement: ........................IV

Instructions for Care and Operation ...............................VI

Power Safety ................................................................ VIII

Battery Precautions .........................................................IX

Cleaning ........................................................................... X

Servicing .......................................................................... X

Travel Considerations .....................................................XI

Quick Start Guide

Overview ........................................................................1-1

Advanced Users .............................................................1-2

Beginners and Not-So-Advanced Users ........................1-2

Warning Boxes ..............................................................1-2

Not Included ..................................................................1-3

System Startup ...............................................................1-4

Model Differences .........................................................1-5

System Software ............................................................1-5

System Map: LCD Panel Open ......................................1-6

LED Indicators ...............................................................1-7

Hot Key Buttons & Keyboard .......................................1-8

Keyboard ........................................................................1-9

Function/Hot Key Indicators .......................................1-10

System Map: Front & Left Views ................................1-11

System Map: Right & Rear Views ..............................1-12

System Map: Bottom View ..........................................1-13

3.75G/HSPA Module USIM Card Installation ............1-14

Docking Port ................................................................1-15

Windows 7 Start Menu & Control Panel .....................1-16

Video Features .............................................................1-17

Power Options ..............................................................1-19

Features & Components

Overview ........................................................................2-1

Hard Disk Drive .............................................................2-2

Optical (CD/DVD) Device ............................................2-3

Loading Discs ................................................................2-3

Handling CDs or DVDs .................................................2-4

DVD Regional Codes ....................................................2-5

9-in-1 Card Reader .........................................................2-6

ExpressCard Slot ............................................................2-7

Inserting and Removing ExpressCards ..........................2-7

TouchPad and Buttons/Mouse .......................................2-7

Gestures and Device Settings ........................................2-8

Audio Features .............................................................2-12

XVI

Preface

Optimizing Audio Recording ......................................2-13

Adding a Printer ...........................................................2-14

USB Printer ..................................................................2-14

Parallel Printer .............................................................2-14

Power Management

Overview ........................................................................3-1

The Power Sources ........................................................3-2

AC/DC Adapter .............................................................3-2

Battery ............................................................................3-2

Turning On the Computer ..............................................3-3

Power Plans ...................................................................3-4

Power-Saving States ......................................................3-6

Sleep ..............................................................................3-6

Hibernate ........................................................................3-7

Shut down ......................................................................3-7

Configuring the Power Buttons .....................................3-8

Resuming Operation ......................................................3-9

Energy Star Power Saving ...........................................3-10

Battery Information .....................................................3-12

Battery Power ..............................................................3-12

Conserving Battery Power ...........................................3-13

Battery Life ..................................................................3-14

New Battery .................................................................3-14

Recharging the Battery with the AC/DC Adapter .......3-14

Proper handling of the Battery Pack ............................3-15

Battery FAQ .................................................................3-16

Drivers & Utilities

What to Install ................................................................4-1

Module Driver Installation .............................................4-1

Driver Installation ..........................................................4-2

Updating/Reinstalling Individual Drivers ......................4-4

User Account Control ....................................................4-4

Windows Security Message ...........................................4-4

New Hardware Found ....................................................4-5

Driver Installation Procedure .........................................4-5

Chipset ...........................................................................4-5

Video ..............................................................................4-5

LAN ...............................................................................4-6

CardReader ....................................................................4-6

TouchPad .......................................................................4-6

Modem ...........................................................................4-6

Hot Key ..........................................................................4-6

Audio .............................................................................4-7

Windows Experience Index ...........................................4-7

Optional Drivers ............................................................4-8

Wireless LAN Module ...................................................4-9

PC Camera Module ........................................................4-9

3.75G/HSPA Module .....................................................4-9

XVII

Preface

Fingerprint Reader Module ............................................4-9

MEI Driver .....................................................................4-9

TPM Driver ....................................................................4-9

BIOS Utilities

Overview ........................................................................5-1

The Power-On Self Test (POST) ...................................5-2

Failing the POST ...........................................................5-3

Fatal Errors ....................................................................5-3

Non-Fatal Errors ............................................................5-3

Intel® vPro™ technology ..............................................5-4

Accessing the Intel Management Engine ......................5-4

The Setup Program ........................................................5-7

Entering Setup ...............................................................5-7

Setup Screens .................................................................5-8

Main Menu .....................................................................5-9

System Time & Date (Main Menu) ...............................5-9

SATA Port 1/2/3/4 (Main Menu) ................................5-10

System Memory/Extended Memory (Main Menu) .....5-10

BIOS Revision/KBC/

EC Firmware Revision (Main Menu) ..........................5-10

Advanced Menu ...........................................................5-11

Advanced Chipset Control ...........................................5-11

Legacy USB Support (Advanced Menu) .....................5-12

Boot-time Diagnostic Screen (Advanced Menu) .........5-12

Legacy OS Boot: (Advanced Menu) ...........................5-12

Power on Boot Beep (Advanced Menu) ......................5-12

Battery Low Alarm Beep (Advanced Menu) ...............5-12

Advanced Chipset Control Menu ................................5-13

On Board JMicron Power Saving >

Advanced Chipset Control ...........................................5-13

Intel Trusted Execution >

Advanced Chipset Control (Model A Only) ................5-14

Intel Virtualization Technology >

Advanced Chipset Control ...........................................5-14

VT-d Technology > Advanced Chipset Control ..........5-14

External Serial port > Advanced Chipset Control .......5-14

SPI Flash Config Lock-Down >

Advanced Chipset Control ...........................................5-14

Security Menu ..............................................................5-15

Set Supervisor Password (Security Menu) ..................5-15

Set User Password (Security Menu) ............................5-16

Password on boot: (Security Menu) .............................5-16

TPM (Trusted Platform Module) Support:

(Security Menu) ...........................................................5-16

TPM State ....................................................................5-17

Change TPM State (TPM State) ..................................5-17

Boot Menu ...................................................................5-19

Exit Menu ....................................................................5-20

XVIII

Preface

Upgrading The Computer

Overview ........................................................................6-1

When Not to Upgrade ....................................................6-2

Removing the Battery ....................................................6-3

Upgrading the Hard Disk Drive .....................................6-4

Upgrading the Optical (CD/DVD) Device ....................6-6

Upgrading the System Memory (RAM) ........................6-8

Modules & Options

Overview ........................................................................7-1

Bluetooth Module ..........................................................7-2

Bluetooth Configuration in Windows 7 .........................7-3

Wireless LAN Module ...................................................7-7

Intel® Wi-Fi Link Series Driver Installation .................7-8

3rd Party 802.11b/g/n

Driver Installation (Model B Only) ...............................7-8

Connecting to a Wireless Network in Windows 7 .........7-9

Windows Mobility Center ...........................................7-12

PC Camera Module ......................................................7-13

PC Camera Driver Installation .....................................7-14

3.75G/HSPA Module ...................................................7-20

Mobile Partner .............................................................7-23

Mobile Partner Application Installation ......................7-23

Mobile Partner Application .........................................7-24

Profile Management .....................................................7-24

Text Messaging Service ...............................................7-28

Security Modules (Fingerprint & TPM) ......................7-29

Fingerprint Reader Module ..........................................7-30

Fingerprint Reader Driver Installation .........................7-30

User Enrollment ...........................................................7-31

Fingerprint Control Center Features ............................7-33

MEI Driver ...................................................................7-34

Intel® Management and Security Status .....................7-35

Trusted Platform Module .............................................7-40

Initializing TPM ...........................................................7-40

TPM Driver Installation ...............................................7-43

Initializing TPM ...........................................................7-44

Infineon Security Platform Settings Tool ....................7-47

Troubleshooting

Overview ........................................................................8-1

Basic Hints and Tips ......................................................8-2

Backup and General Maintenance .................................8-3

Viruses ...........................................................................8-4

Upgrading and Adding New Hardware/Software ..........8-5

Problems and Possible Solutions ...................................8-7

Bluetooth Connection Problems ..................................8-13

XIX

Preface

Interface (Ports & Jacks)

Overview .......................................................................A-1

Intel Video Driver Controls

Intel Video Driver Installation ...................................... B-1

Video ............................................................................. B-1

Dynamic Video Memory Technology ...................... B-1

Intel® Graphics & Media Control Panel ...................... B-2

Display Devices & Options ...................................... B-4

Attaching Other Displays ............................................. B-5

Configuring an External Display in Windows 7 ...........B-7

HDMI Audio Configuration ....................................... B-10

Specifications

Processors For All Models ............................................C-2

Processor For Model B Only ........................................C-2

Core Logic .................................................................... C-2

Display .......................................................................... C-2

Memory ......................................................................... C-2

Video Adapter ...............................................................C-3

BIOS ............................................................................. C-3

Storage .......................................................................... C-3

Audio ............................................................................ C-3

Keyboard & Pointing Device ........................................ C-3

Interface ........................................................................C-3

Card Reader ..................................................................C-3

Slots ..............................................................................C-3

Communication .............................................................C-4

Power Management ......................................................C-4

Power ............................................................................C-4

Security .........................................................................C-4

Operating System ..........................................................C-4

Environmental Spec ......................................................C-4

Dimensions & Weight ..................................................C-4

Preface

Overview 1 - 1

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the

computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, Card Reader, ExpressCard/34/54), Touchpad & Mouse, Audio & Printer.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s Bluetooth, Wireless LAN, PC Camera, 3.75G/HSPA and Secu-

rity modules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the Intel Video driver controls.

• Appendix C The computer’s specification.

1 - 2 Overview

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful

to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on

page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then

the information contained in the Quick Start Guide should be enough to get you up

and running. Eventually you should try to look through all the documentation (more

detailed descriptions of the functions, setup and system controls are covered in the

remainder of the User’s Manual), but do not worry if you do not understand every-

thing the first time. Keep this manual nearby and refer to it to learn as you go. You

may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.



Notes

Check the light colored

boxes with the mark

above to find detailed in-

formation about the com-

puter’s features.

Overview 1 - 3

Quick Start Guide

Not Included

Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs)

have their own manuals, so please consult the appropriate manuals.



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install

the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com-

puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order

listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If

your system hasn’t been properly configured (your service representative may have already done that for you); refer to

Chapter 4 for installation instructions.

Ports and Jacks

See Appendix A for a description of the interface (ports & jacks) which allow your computer to communicate with external

devices, connect to the internet etc.

1 - 4 Overview

Quick Start Guide

System Startup

1. Remove all packing materials.

2. Place the computer on a stable surface.

3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter.

5. Use one hand to raise the

lid/LCD to a comfortable viewing angle (do not exceed 120 degrees);

use the other

hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by

the lid/LCD).

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD/



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command from the Start menu in Win-

dows. This will help prevent hard disk or system problems.

Model Differences 1 - 5

Quick Start Guide

Model Differences

This notebook series includes two different model types that mainly differ as indicated in the table below. Note

that your model may appear slightly different from those pictured in this manual.

Table 1 - 1 - Model Differences

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you

are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7

operating system.

Feature Model A Model B

CPU & Chipset

Supported

See “Specifications” on page C - 1 for a full information on the Chipsets and CPUs

supported by each model.

Docking Station

Factory Option Supplied as Standard



Windows OS

In order to run Windows 7 without limitations or decreased performance, your computer requires a minimum 1GB of sys-

tem memory (RAM), however if you are running Windows 7 64 bit your computer requires a minimum 2GB of system

memory (RAM).

1 - 6 System Map: LCD Panel Open

Quick Start Guide

System Map: LCD Panel Open

Figure 1 - 2

LCD Panel Open

1. Built-In PC Camera

2. LCD

3. Speakers

4. Power Button

5. Hot Key Buttons

6. Keyboard

7. Built-In Microphone

8. Touchpad &

Buttons

9. Fingerprint Module

Note that the valid operational

area for the Touchpad’s scroll

bar and Buttons is that indi-

cated within the red dotted

lines above.



Wireless Device

Operation Aboard

Aircraft

The use of any portable

electronic transmission

devices aboard aircraft is

usually prohibited. Make

sure the module(s) are

OFF if you are using the

computer aboard aircraft.

Use the key combinations

to toggle power to the

3.75G/HSPA/WLAN/

Bluetooth modules, and

check the LED indicator

icon to see if the modules

are powered on or not (see

Table 1 - 5, on page 1 -

10/ Table 1 - 3, on page 1

- 7).

LED Indicators 1 - 7

Quick Start Guide

LED Indicators

The LED indicators on the computer display helpful

information about the current status of the computer.

Table 1 - 2 - LED Status Indicators

Table 1 - 3 - LED Power & Communication Indicators

Icon Color Description

Green Hard Disk Activity

Green Number Lock Activated

Green Caps Lock Activated

Green

Scroll Lock Activated (to activate

press Fn & Scr Lk)

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking Green

The Computer is in Sleep

Mode

Orange The Battery is Charging

Green The Battery is Fully Charged

Blinking Orange

The Battery Has Reached

Critically Low Power Status

Green

The (optional) Wireless LAN

Module is Powered On

Orange

The (optional) Bluetooth

Module is Powered On

1 - 8 Hot Key Buttons & Keyboard

Quick Start Guide

Hot Key Buttons & Keyboard

These buttons give instant access to the default Internet browser and e-mail program,

and allow you to toggle the Silent Mode on/off with one quick button press.

Table 1 - 4 - Hot Key Buttons

*When enabled, Silent Mode will reduce fan noise and save power consumption.

Note this may reduce computer performance.

Hot Key Function

Activate the Default E-Mail Browser (Note that in Windows 7 this button

will only function after Outlook or Outlook Express are installed)

Activate the Default Internet Program

Toggle *Silent Mode (for power saving)



Other Keyboards

If your keyboard is

damaged or you just

want to make a

change, you can use

any standard USB key-

board. The system will

detect and enable it

automatically. Howev-

er special functions/

hot-keys unique to the

system’s regular key-

board may not work.

NumLk & ScrLk

Hold down the Fn Key

and either NumLk or

ScrLk to enable num-

ber or scroll lock, and

check the LED indica-

tor for status.



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters.

These special characters can only be produced by using the numeric keypad. Regular number keys (in

the upper row of the keyboard) will not work. Make sure that NumLk is on.

Keyboard 1 - 9

Quick Start Guide

Keyboard

The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to

allow you to change operational features instantly. See Table 1 - 5, on page 1 - 10 for full function key combi-

nation details.

Figure 1 - 3 - Keyboard

Numerical Keypad

Play/Pause Key

Function Keys

NumLk &

ScrLk Keys

Fn Key

Toggle Key

3.75G/HSPA Module

Power

1 - 10 Function/Hot Key Indicators

Quick Start Guide

Function/Hot Key Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition

to the basic function key combinations; visual indicators are available when the hot key utility is installed.

Table 1 - 5 - Function & Hot Key Indicators

Keys Function Keys Function

Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle

Fn +

3.5G Module Power

Toggle

Fn + F8/F9

Brightness Decrease/Increase

Fn + F1

TouchPad Toggle

Fn + F10

PC Camera Power Toggle

Fn + F2

Turn LCD Backlight Off

(Press a key to or use TouchPad to turn on)

Fn + F11

*WLAN Module Power Toggle

Fn + F3

Mute Toggle

Fn + F12

Bluetooth Module Power Toggle

Fn + F4 Sleep Toggle

**Silent Mode Toggle

Fn + F5/F6

Volume Decrease/Increase

*Make sure that Wireless is ON in the Windows Mobility Center to ensure

proper wireless function key behavior (see page 3 - 12).

**When enabled, Silent Mode will reduce fan noise and save power

consumption. Note this may reduce computer performance.

System Map: Front & Left Views 1 - 11

Quick Start Guide

System Map: Front & Left Views

Figure 1 - 4

Front & Left Views

1. LED Power & Com-

munication Indica-

tors

2. DC-In Jack

3. External Monitor

Port

4. RJ-45 LAN Jack

5. e-SATA Port

6. HDMI-Out Port

7. Vent/Fan Intake/

Outlet

8. 2 * USB 2.0 Ports

9. ExpressCard Slot

(see page 2 - 7)

10. 9-in-1 Card Reader



9-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RS MMC

SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible

MS (Memory Stick) / MS Pro / MS Duo

1 - 12 System Map: Right & Rear Views

Quick Start Guide

System Map: Right & Rear Views

Figure 1 - 5

Right & Rear Views

1. S/PDIF-Out Jack

2. Microphone-In

Jack

3. Headphone-Out

Jack

4. USB 2.0 Port

5. Optical Device

Drive Bay (for CD/

DVD Device - see

page 2 - 3)

6. RJ-11 Phone Jack

7. Security Lock Slot

8. Battery



Disk Eject Warning

Don’t try to eject a CD/DVD

while the system is accessing

it. This may cause the system

to “crash”. Stop the disk first

then eject it, or press the stop

button twice.



CD/DVD Emergency Eject

If you need to manually eject a CD/

DVD (e.g. due to an unexpected

power interruption) you may push the

end of a straightened paper clip into

the emergency eject hole. Do not use

a sharpened pencil or any object that

may break and become lodged in the

hole. Don’t try to remove a floppy

disk/CD/DVD while the system is ac-

cessing it. This may cause the sys-

tem to “crash”.



Changing DVD Regional Codes

Go to the Control Panel and double-click Device

Manager (Hardware and Sound), then click the +

next to DVD/CD-ROM drives. Double-click on the

DVD-ROM device to bring up the Properties dialog

box, and select the DVD Region (tab) to bring up

the control panel to allow you to adjust the regional

code.

DVD region detection is device dependent, not OS-

dependent. You can select your module’s region

code 5 times. The fifth selection is permanent. This

cannot be altered even if you change your operating

system or you use the module in another computer.

System Map: Bottom View 1 - 13

Quick Start Guide

System Map: Bottom View

Figure 1 - 6

Bottom View

1. Battery

2. Docking Port

3. RAM & CPU Bay

Cover

4. Vent/Fan Intake/

Outlet

5. Hard Disk Bay

Cover

Note: the 3.75G/HSPA

USIM Card is located un-

der the RAM & CPU Bay

Cover.



Battery Information

Always completely dis-

charge, then fully charge, a

new battery before using it.

Completely discharge and

charge the battery at least

once every 30 days or after

about 20 partial discharges.

See “Battery Information”

on page 3 - 12 for full in-

structions.



CPU

The CPU is not a user serviceable part.

Overheating

To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake

while the computer is in use.

1 - 14 3.75G/HSPA Module USIM Card Installation

Quick Start Guide

3.75G/HSPA Module USIM Card Installation

If you have included an optional 3.75G/HSPA module in your purchase option, follow the instructions below to

install the USIM card (which will be provided by your service provider), and then run the Mobile Partner ap-

plication. See “Mobile Partner” on page 7 - 23 for instructions on installing the program etc.

1. Turn off the computer, and turn it over and then remove the battery (slide the latches in the direction indicated

below and slide the battery out).

2. Insert the USIM card into the slot at the rear of the battery compartment, as illustrated below, until it clicks fully

into position, and replace the battery.

Figure 1 - 7 - Battery Removal & USIM Card Insertion



USIM Card Orientation

Note that the USIM card’s readable

side (with the gold-colored contacts)

should face upwards as illustrated.

Docking Port 1 - 15

Quick Start Guide

Docking Port

Follow the instructions below before connecting the computer to the docking station, if included in your pur-

chase configuration (Factory Option for Model A computers). Failure to open the cover of the docking port

before connecting the computer to the docking station may result in irreparable damage to the connector on the

docking station.

1. Turn the computer over.

2. Slide the docking port cover latch in the direction of the arrow at point to open the cover.

3. After disconnecting the computer from the docking station, slide the docking port cover latch in the direction of

the arrow at point .



Docking Port

Cover

Make sure you keep

the cover closed

when the computer is

not docked in the sta-

tion. This will help

prevent foreign ob-

jects and/or dust get-

ting in to the contact

area.

Figure 1 - 8 - Opening and Closing the Docking Port

Note that the system cannot be connected to the docking station if the 9 cell battery is

inserted in the battery compartment.

1 - 16 Windows 7 Start Menu & Control Panel

Quick Start Guide

Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac-

cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk

drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu

icon , and then select Properties if you want to customize the appearance of the Start menu.

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control

Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features

in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features,

however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all

controls it may be necessary to toggle off Category View to view the control panel icons.

Figure 1 - 9 - Start Menu & Control Panel

Click here to toggle Category View

Video Features 1 - 17

Quick Start Guide

Video Features

You can configure display options from the Display (Control Panel) and Screen Resolution in Windows. For

more detailed video information see“Intel Video Driver Controls” on page B - 1.

To access Display (Control Panel) and Screen Resolution in Windows:

1. Click Start and click Control Panel.

2. Click Display (icon) - In the Appearance and Personalization category.

3. Click Adjust Screen Resolution/Adjust resolution.

4. Alternatively you can right-click the desktop and select Screen resolution (Figure 1 - 10).

5. Use the dropbox to select the screen Resolution (Figure 1 - 10).

6. Click Advanced settings (Figure 1 - 10) to bring up the Advanced properties tabs.

Figure 1 - 10 - Screen Resolution

1 - 18 Video Features

Quick Start Guide

To access the Intel(R) Graphics Media Accelerator Driver for mobile control panel:

1. Click Advanced settings (Figure 1 - 10 on page 1 - 17) in the Screen Resolution control panel in Win-

dows.

2. Click the Intel(R)... tab and click Graphics Properties (button) (Figure 1 - 11) .

3. Right-click the desktop and select Graphics Properties from the menu.

4. Click the icon in the taskbar and select Graphics Properties from the menu.

Figure 1 - 11 - Intel GMA Driver for Mobile Control Panel

Power Options 1 - 19

Quick Start Guide

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 13) allows you

to configure power management features for your computer. You can conserve power by means of power plans

and configure the options for the power button, sleep button, computer lid (when closed), display and sleep

mode from the left menu. Note that the Power saver plan may have an affect on computer performance.

Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to

create a new plan. Click Change plan settings and click Change advanced power settings to access further con-

figuration options.

Pay attention to the instructions on battery care in “Battery Information” on page 3 - 12.

Figure 1 - 12 - Power Options

Quick Start Guide

1 - 20

Features & Components

Overview 2 - 1

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components

of the computer:

•Hard Disk Drive

• Optical (CD/DVD) Device

• 9-in-1 Card Reader

• ExpressCard Slot

• TouchPad and Buttons/Mouse

• Audio Features

• Adding a Printer

Features & Components

2 - 2 Hard Disk Drive

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be

taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height

of 9.5 mm.

The hard disk is accessible from the bottom of your computer as seen below. For fur-

ther details see “Upgrading the Hard Disk Drive” on page 6 - 4.



Power Safety

Before attempting to ac-

cess any of the internal

components of your

computer please ensure

that the machine is not

connected to the AC

power, and that the ma-

chine is turned off. Also

ensure that all peripher-

al cables, including

phone lines, are discon-

nected from the comput-

er.

Figure 2 - 1

Hard Disk Location

HDD Bay

Features & Components

Optical (CD/DVD) Device 2 - 3

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de-

vice will depend on the module you purchased (see “Storage” on page C - 3). The

optical device is usually labeled “Drive D:” and may be used as a boot device if

properly set in the BIOS (see “Boot Menu” on page 5 - 19).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto

the disc tray with label-side facing up (use just enough force for the disc to click onto

the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you

are ready to start. The busy indicator will light up while data is being accessed,

or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt-

ed, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.



Sound Volume

Adjustment

How high the sound vol-

ume can be set depends

on the setting of the vol-

ume control within Win-

dows. Click the Volume

icon on the taskbar to

check the setting (see

“Audio Features” on

page 2 - 12).

Figure 2 - 2

Optical Device

Features & Components

2 - 4 Optical (CD/DVD) Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please

follow the advice below to make sure that the data stored on your CDs/DVDs can be

accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.



CD Emergency Eject

If you need to manually

eject a CD (e.g. due to

an unexpected power

interruption) you may

push the end of a

straightened paper clip

into the emergency eject

hole. However please

do NOT use a sharp-

ened pencil or similar

object that may break

and become lodged in

the hole.

Disk Eject Warning

Don’t try to remove a

CD/DVD while the sys-

tem is accessing it. This

may cause the system

to “crash”.

Features & Components

Optical (CD/DVD) Device 2 - 5

DVD Regional Codes

To change the DVD regional codes see “Changing DVD Regional Codes” on

page 1 - 12.

DVD Regional Coding

Region Geographical Location

1 USA, Canada

Western Europe, Japan, South

Africa, Middle East & Egypt

South-East Asia, Taiwan, South

Korea, The Philippines, Indonesia,

Hong Kong

South & Central America, Mexico,

Australia, New Zealand

N Korea, Russia, Eastern Europe,

India & Most of Africa

6China

Table 2 - 1

DVD Regional Coding

Features & Components

2 - 6 9-in-1 Card Reader

9-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the

card into the slot and it will appear as a removable device, and can be accessed in

the same way as your hard disk (s). Make sure you install the card reader driver (see

“CardReader” on page 4 - 6).

*Note: The PC adapters are usually supplied with these cards.



Card Reader Cover

Make sure you keep the

rubber cover provided in

the card reader when

not in use. This will help

prevent foreign objects

and/or dust getting in to

the card reader.

Figure 2 - 3

Left View

1. Card Reader

• MMC (MultiMedia Card) / RS MMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible

• MS (Memory Stick) / MS Pro / MS Duo

Features & Components

ExpressCard Slot 2 - 7

ExpressCard Slot

The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/

34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC

Cards). Make sure you install the Card Reader driver

(see

“CardReader” on page 4

- 6

ExpressCard/54 is used for applications which require a larger interface slot, e.g.

CompactFlash card reader. The number denotes the card width; 54mm for the Ex-

press Card/54 and 34mm for the ExpressCard/34.

Inserting and Removing ExpressCards

• Align the ExpressCard with the slot and push it in until it locks into place (as

pictured in the generic figure below).

• To remove an ExpressCard, simply press the card to eject it.



ExpressCard

Slot Cover

Make sure you keep the

rubber cover provided in

the ExpressCard slot

when not in use. This

will help prevent foreign

objects and/or dust get-

ting in to the Express-

Card Slot.

Figure 2 - 4

Left View

1. Express Card

Slot

Features & Components

2 - 8 TouchPad and Buttons/Mouse

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to

your computer through one of the USB ports. The TouchPad buttons function in

much the same way as a two-button mouse.

Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you

can configure the functions by double-clicking the TouchPad driver icon on the

taskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointer

motion and sensitivity options to your preferences. You will find further information

at www.synaptics.com.



Mouse Driver

If you are using an ex-

ternal mouse your op-

erating system may be

able to auto-configure

your mouse during its

installation or only en-

able its basic functions.

Be sure to check the

device’s user docu-

mentation for details.

Figure 2 - 5

Mouse Properties

Features & Components

TouchPad and Buttons/Mouse 2 - 9

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (ac-

tion) on the surface of the TouchPad to perform specific actions to manipulate doc-

uments, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (tab) and click Settings.

4. Use the menu tree on the left to access the user configurable settings.



Show Video

You can get a clearer

view of the gestures in-

volved by clicking the

Show Video option for

each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three

Fingers Down and

Three Finger Flick) in the

Device Settings > Set-

tings left tree menu

and click the Show Video

button to see the demon-

stration video.

For more details on any of

the gestures see the help

in the lower part of the

right menu window.

Figure 2 - 6

Mouse Properties -

Device Settings

Features & Components

2 - 10 TouchPad and Buttons/Mouse

Scrolling

The Two-Finger scrolling feature works in most scrollable windows and allows you

to scroll horizontally and vertically. Place two fingers, slightly separated, on the

TouchPad surface and slide both fingers in the direction required (in a straight con-

tinuous motion).

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel

in Windows applications that support CTRL + scroll wheel zoom functionality.

Place two fingers on the TouchPad (for best results use the tips of the fingers) and

slide them apart to zoom in, or closer together to zoom out.

Figure 2 - 7

Scrolling Gesture

Figure 2 - 8

Zooming Gesture

Features & Components

TouchPad and Buttons/Mouse 2 - 11

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.

Place a finger down on the left “target” zone and keep it stationary. Place another

finger near the middle of the TouchPad and slide it in a circular motion around the

stationary finger (clockwise or counterclockwise) to rotate the object.

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of

applications such as browsing the Internet or scrolling through a photo viewer. The

Three Fingers Down gesture may be used to launch user-selectable applications.

Figure 2 - 9

Rotating Gesture

Figure 2 - 10

Flick/Press

Gesture

Features & Components

2 - 12 Audio Features

Audio Features

You can configure the audio options on your computer from the Sound control

panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/

control panel (right-click the taskbar icon to bring up an audio menu). The volume

may also be adjusted by means of the Fn + F5/F6 key combination.



Sound Volume

Adjustment

The sound volume level

is set using the volume

control within Windows

(and the volume func-

tion keys on the comput-

er). Click the volume

icon in the taskbar to

check the setting.

Figure 2 - 11

Realtek Audio

Manager

Right-click the icon

to access the menu

above.

Features & Components

Audio Features 2 - 13

Optimizing Audio Recording

Follow these instructions to optimize your audio recording.

1. Double-click the taskbar icon to bring up the Realtek HD Audio Manager.

2. Click the Microphone tab.

3. Click the Noise Suppression button to prevent any background noise or

feedback.

4. Click OK to close the Realtek HD Audio Manager.

Figure 2 - 12

Optimizing Audio

Recording

Features & Components

2 - 14 Adding a Printer

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will

help you to add a printer; however it is always best to refer to the printer manual for

specific instructions and configuration options.

USB Printer

Most current printers have a USB interface connection. You may use any one of the

ports to connect the printer.

Install Instructions:

1. Set up the printer according to its instructions (unpacking, paper tray, toner/ink car-

tridge etc.).

2. Turn ON the computer.

3. Turn ON the printer.

4. Connect the printer’s USB cable to one of the USB ports on the computer.

5. Windows will identify the printer and either load one of its own drivers or ask you

to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the sidebar,

however you will need to purchase a parallel to USB converter.



Parallel Printer

After setting up the print-

er attach the parallel ca-

ble to the printer.

Connect the printer’s

parallel cable to the Par-

allel to USB converter,

and then plug the con-

verter into the USB port.

Turn ON the printer,

then turn ON the com-

puter.

Windows will identify the

printer and either load

one of its own drivers or

ask you to supply one.

Follow the on-screen in-

structions.

Power Management

Overview 3 - 1

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power man-

agement conserves power by controlling individual components of the computer

(the monitor and hard disk drive) or the whole system. This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Energy Star Power Saving

The computer uses enhanced power saving techniques to give the operating system

(OS) direct control over the power and thermal states of devices and processors. For

example, this enables the OS to set devices into low-power states based on user set-

tings and information from applications.



OS Note

Power management

functions will vary slight-

ly depending on your

operating system. For

more information it is

best to refer to the user’s

manual of your operat-

ing system.

Power Management

3 - 2 The Power Sources

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/

DC adapter will damage the computer and its components.

1. Attach the AC/DC adapter to the DC-in jack on the left of the computer.

2. Plug the AC power cord into an outlet, and then connect the AC power cord to the

AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an

electrical outlet is unavailable. Battery life varies depending on the applications and

the configuration you're using. To increase battery life, let the battery discharge

completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 16).

We recommend that you do not remove the battery. For more information on the bat-

tery, please refer to “Energy Star Power Saving” on page 3 - 10.



Silent Mode

Use the key to tog-

gle Silent Mode to re-

duce fan noise and save

power consumption.

Note this may reduce

computer performance.

Power Management

Turning On the Computer 3 - 3

Turning On the Computer

Now you are ready to begin using your computer. To turn it on simply press the pow-

er button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/

Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and

holding the power button for longer than this will shut the computer down). Use

Power Options in the Windows control panel to configure this feature.



Forced Off

If the system “hangs”,

and the Ctrl + Alt + Del

key combination doesn’t

work, press the power

button for 4 seconds, or

longer, to force the sys-

tem to turn itself off.

Power Button as

Stand by or

Hibernate Button

You can use the OS’s

“Power Options” control

panel to set the power

button to send the sys-

tem into Stand by or Hi-

bernate mode (see your

OS’s documentation, or

“Configuring the Pow-

er Buttons” on page 3

- 8 for details).



Shut Down

Note that you should always shut your computer down by choosing the Shut Down com-

mand from the bottom right of the Start menu in Windows. This will help prevent hard disk

or system problems.

Power Management

3 - 4 Power Plans

Power Plans

The computer can be configured to conserve power by means of power plans. You

can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and

to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to ac-

cess further configuration options in Advanced Settings.



Resuming

Operation

See Table 3 - 1, on

page 3 - 9 for informa-

tion on how to resume

from a power-saving

state.

Password

It is recommended that

you enable a password

on system resume in or-

der to protect your data.

Figure 3 - 1

Power Plan

Advanced Settings

Power Management

Power Plans3-5

Each Windows power plan will also adjust the processor performance of your ma-

chine in order to save power. This is worth bearing in mind if you are experiencing

any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view

the High performance plan) for maximum performance when the computer is pow-

ered from an AC power source. Choose the Power saver (bear in mind that this

scheme may slow down the overall performance of the computer in order to save

power) for maximum power saving when the computer is battery (DC power) pow-

ered.

Figure 3 - 2

Power Plans

Click to Show/Hide

additional

power plans

Power Management

3 - 6 Power-Saving States

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where

you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the

system sleeps. When you are not using your computer for a certain length of time,

which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left

off (what was on your desktop) without reopening the application(s) and file(s) you

last used.

If your mobile PC in Sleep is running on battery power the system will use only a

minimum amount of power. After an extended period the system will save all the

information to the hard disk and shut the computer down before the battery becomes

depleted.

Power Management

Power-Saving States 3 - 7

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves

all of your information on a part of the hard disk before it turns the system off. If a

power failure occurs the system can restore your work from the hard disk; if a power

failure occurs when work is saved only to memory, then the work will be lost. Hi-

bernate will also return you to where you last left off within seconds. You should

put your mobile PC into Hibernate if you will not use the computer for a period of

time, and will not have the chance to charge the battery.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t for-

get to remove the battery and follow all the safety instructions in Chapter 6), plan

to be away from the computer for several days, or you do not need it to wake up and

run a scheduled task. Returning to full operation from Shut down takes longer than

from Sleep or Hibernate.



Silent Mode

You can use Silent

Mode to reduce power

consumption and fan

noise.

Use the Silent Mode

hot key to toggle

this mode on/off.

On screen visual indica-

tors will display the Si-

lent Mode status (see

Table 1 - 3, on page 1 -

Note Silent Mode may

reduce computer perfor-

mance.

Figure 3 - 3

Lock Button menu

Power Management

3 - 8 Configuring the Power Buttons

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the

computer in to a power-saving state. Click Choose what the power buttons do on

the left menu in Power Options to bring up the menu.



Password

Protection

It is recommended that

you enable a password

on wake up in order to

protect your data.

However you can dis-

able this setting from the

Power Options menu

by clicking Require a

password on wakeup

in the left menu, and se-

lecting the options (click

Change settings that

are currently unavail-

able).

Figure 3 - 4

Power Options

Define Power

Buttons

Power Management

Configuring the Power Buttons 3 - 9

Resuming Operation

You can resume operation from power-saving states by pressing the power button,

or in some cases pressing the sleep button (Fn + F4 key combo).

Power Status

Icon Color

To Resume

Power Off Off Press the Power Button

Sleep Blinking Green

Press the Power Button

Press the Sleep Button (Fn + F4 Key Combo)

Hibernate

Off (battery)

Press the Power Button

Orange (AC/DC adapter)

Display Turned Off Green Press a Key or Move the Mouse/Touchpad



Closing the Lid

If you have chosen to

send the computer to

Sleep when the lid is

closed, raising the lid

will wake the system up.

Table 3 - 1

Resuming

Operation



3.75G/HSPA

Modules & System

Wake Up

Note that the 3.75G mod-

ules

DO NOT

support

system wake up on

3.75G/HSPA modem ac-

tivity.



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down

hot key button when it is pressed for less than 4 seconds (pressing and holding the power

button for longer than this will force the computer to shut down).

Power Management

3 - 10 Configuring the Power Buttons

Energy Star Power Saving

This system supports Energy Star power management features that place comput-

ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period

of inactivity. If you want to enable Energy Star power saving then follow these in-

structions:

1. Right-click the taskbar icon (see sidebar).

2. Select Power Conservation Modes.



Taskbar Icon

If the taskbar icon does

not appear then click the

taskbar arrow and select

Customize.

Select Show icon and

notifications alongside

the Hotkey icon and

click OK. The icon

will now appear in the

taskbar.

Figure 3 - 5

Energy Star Menu



Docking

The Docking menu item will

appear when you right-click

the taskbar icon , howev-

er this item can only be used

when the computer is

docked with the docking sta-

tion.

Power Management

Configuring the Power Buttons 3 - 11

3. Select Energy Star to use the Energy Star power management and override other

power saving settings.

Conservation Modes

• The default Energy Star setting will result in maximum power saving, but with

the possible loss of some performance.

• Setting the mode to Balance will give power saving matched with performance.

• Performance will give optimum computer performance but with less power

conservation.

Figure 3 - 6

Energy Star Menu

Power Management

3 - 12 Battery Information

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the pro-

grams you are running, and peripheral devices attached. You can set actions to be

taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from

power plan Change plan settings > Change advanced power settings (see Figure

3 - 2 on page 3 - 5).

Click the battery icon in the taskbar to see the current battery level and charge

status.



Low Battery

Warning

When the battery is criti-

cally low, immediately

connect the AC/DC

adapter to the computer

or save your work, oth-

erwise, the unsaved

data will be lost when

the power is depleted.

Figure 3 - 7

Battery Icon

(Taskbar) & Battery

Advanced Settings

Power Management

Battery Information 3 - 13

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD

brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or communication applications when they are

not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices,

ExpressCards etc.



Wireless Hot Keys

The computer’s wireless

function keys will not func-

tion properly if Wireless is

turned OFF in the Win-

dows Mobility Center

control panel.

The wireless indicators

may show that

the WLAN module is pow-

ered on, however if wire-

less is OFF in the Mobility

Center, the module will not

be powered on.

Make sure that Wireless is

ON in the Mobility Center to

ensure proper function key

behavior.

Figure 3 - 8

Windows Mobility

Center



Windows Mobility

Center

The Windows Mobili-

ty Center control pan-

el provides an easy

point of access for in-

formation on battery

status, power plans

used and wireless de-

vice status etc.

Make sure Wireless is ON to ensure proper function key behavior.

Power Management

3 - 14 Battery Information

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life

and improve its performance, fully discharge and recharge the battery at least

once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to re-

move the battery for any reason see “Removing the Battery” on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 16 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and

plugged into an electrical outlet. If the computer is powered on, and in use, it will

take several hours to fully recharge the battery. When the computer is turned off but

plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-

tors” on page 1 - 7 for information on the battery charge status, and to “Energy Star

Power Saving” on page 3 - 10 for more information on how to maintain and prop-

erly recharge the battery pack.)

Power Management

Battery Information 3 - 15

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances

• DO NOT expose the battery to fire or high temperatures, it may explode

• DO NOT connect the metal terminals (+, -) to each other



Caution

Danger of explosion if

battery is incorrectly re-

placed.

Replace only with the

same or equivalent type

recommended by the

manufacturer. Discard

used battery according

to the manufacturer’s in-

structions.



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent out of shape after being

dropped), or any unusual smells emanating from the notebook battery, shut your computer

down immediately and contact your service center. If the battery has been dropped we do

not recommend using it any further, as even if the computer continues to work with a dam-

aged battery in place, it may cause circuit damage, which may possibly result in fire. It is

recommended that you replace your computer battery every two years.

Power Management

3 - 16 Battery Information

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t

turn off the computer even if a message indicates the battery is critically low, just let

the computer use up all of the battery power and shut down on its own.

1. Save and close all files and applications.

2. Create a power plan for discharging the battery and set all the options to Never.

Figure 3 - 9

Power Plan Create

Power Management

Battery Information 3 - 17

3. Click Change plan settings (after creating it) and click Change plan settings >

Change advanced power settings.

Figure 3 - 10

Change Plan

Settings / Change

Advanced Power

Settings

Power Management

3 - 18 Battery Information

4. Scroll down to Battery and click + to expand the battery options.

5. Choose the options below (click Yes if a warning appears):

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

Figure 3 - 11

Power Options

Advanced Settings -

Battery

Power Management

Battery Information 3 - 19

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes

from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after

about 20 partial discharges.

Power Management

3-20

Drivers & Utilities

What to Install 4 - 1

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of

the computer’s subsystems. The system takes advantage of some newer hardware components for which the lat-

est versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system

components won’t be auto-configured with an appropriate driver or utility during operating system installation.

Instead, you need to manually install some system-required drivers and utilities.

What to Install

The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper

operation of the computer.

Module Driver Installation

The procedures for installing drivers for the Wireless LAN, PC Camera, 3.75G/HSPA, Fingerprint and TPM

modules are provided in “Modules & Options” on page 7 - 1.

Make sure any modules (e.g. WLAN, 3.75G/HSPA or PC Camera) are ON before installing the appropriate driv-

er.

Drivers & Utilities

4 - 2 Driver Installation

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers/Option Drivers (button).

Figure 4 - 1 - Drivers Installer Screens

1. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order)

which is the same as that listed in the Drivers Installer menu.

2. Click to select the driver you wish to install, (you should note down the drivers as you install them).

3. Follow the instructions for each individual driver installation procedure as listed on the following pages.

Drivers & Utilities

Driver Installation 4 - 3

Table 4 - 1 - Driver Installation

Manual Driver Installation

Click Browse CD/DVD (button) in the Drivers Install-

er application and browse to the executable file in the

appropriate driver folder.

Windows Update

After installing all the drivers make sure you enable

Windows Update in order to get all the latest security

updates etc. (all updates will include the latest hotfixes

from Microsoft). See “Windows Update” on page 4 -

8 for instructions.

Windows 7 Drivers

Page

Chipset Page 4 - 5

Video Page 4 - 5

LAN Page 4 - 6

CardReader Page 4 - 6

TouchPad Page 4 - 6

Modem Page 4 - 6

Hot Key Page 4 - 6

Audio Page 4 - 7

Wireless LAN Module Page 7 - 8

PC Camera Module Page 7 - 14

3.75G/HSPA Module Page 7 - 23

Fingerprint Reader Module Page 7 - 30

MEI Driver Page 7 - 34

Trusted Platform Module Page 7 - 40

Drivers & Utilities

4 - 4 Driver Installation

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it

may be necessary to uninstall the original driver.To do

this go to the Control Panel in the Windows OS and

double-click the Programs and Features icon (Pro-

grams > Uninstall a program). Click to select the

driver (if it is not listed see below) and click Uninstall,

and then follow the on screen prompts (it may be nec-

essary to restart the computer). Reinstall the driver as

outlined in this chapter.

If the driver is not listed in the Programs and Fea-

tures menu:

1. Click Start, and click Control Panel (or point to

Settings and click Control Panel).

2. Double-click Device Manager (Hardware and

Sound > Device Manager).

3. Double-click the device you wish to update/reinstall

the driver for (you may need to click “+” to expand

the selection).

4. Click Driver (tab) and click the Update Driver or

Uninstall button and follow the on screen prompts.

User Account Control

If a User Account Control prompt appears as part of

the driver installation procedure, click Continue or

Allow, and follow the installation procedure as direct-

ed.

Windows Security Message

If you receive a Windows security message as part of

the driver installation process. Just click “Install this

driver software anyway” or “Install” to continue the

installation procedure.

You will receive this message in cases where the driv-

er has been released after the version of Windows you

are currently using. All the drivers provided will have

already received certification for Windows.

Drivers & Utilities

Driver Installation 4 - 5

New Hardware Found

If you see the message “New Hardware Found” dur-

ing the installation procedure (other than when out-

lined in the driver install procedure), click Cancel

to close the window, and follow the installation proce-

dure.

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual

disc and click Install Drivers (button).

Chipset

1. Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

Video

1. Click 2.Install VGA Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.



Driver Installation General Guidelines

The driver installation procedure outlined in this Chapter

(and in Chapter 7 Options & Modules), are accurate at

the time of going to press.

Drivers are always subject to upgrade and revision so

the exact procedure for certain drivers may differ slight-

ly. As a general guide follow the default on screen in-

structions for each driver (e.g. Next > Next > Finish)

unless you are an advanced user. In many cases a re-

start is required to install the driver.

Make sure any modules (e.g. PC Camera, WLAN or

3.75G/HSPA) are ON before installing the appropriate

driver.

Drivers & Utilities

4 - 6 Driver Installation

LAN

1. Click 3.Install LAN Driver > Yes.

2. Click Install Drivers and Software > Next.

3. Click the button to accept the license and click

Next.

4. Click Next > Install.

5. Click Finish.

6. The network settings can now be configured.

CardReader

1. Click 4.Install Cardreader Driver > Yes.

2. Click Install.

3. Click Finish.

TouchPad

1. Click 5.Install Touchpad Driver > Yes.

2. Click Next.

3. Click the button to accept the license, and then

click Next.

4. Click Finish > Restart Now to restart the com-

puter.

Modem

1. Click 6.Install Modem Driver > Yes.

2. Click OK > OK.

3. The modem is ready for dial-up configuration.

Hot Key

1. Click 7.Install Hotkey AP Driver > Yes.

2. Click Next > Next.

3. Click Finish > Finish to restart the computer.



Modem Country Selection

Go to the Phone and Modem (Options) control panel

(Hardware and Sound) and make sure the modem

country selection is appropriate for you.

Drivers & Utilities

Driver Installation 4 - 7

Audio

1. Click 8.Install Audio Driver > Yes.

2. Click Next.

3. Click Finish to restart the computer.

Note that after installing the audio driver the system

will not return to the Drivers Installer screen. To in-

stall any of the optional drivers listed overleaf, eject

the Device Drivers & Utilities + User’s Manual disc

and then reinsert it (or double-click the disc icon in My

Computer), and click Option Drivers (button) to ac-

cess the optional driver menu.

It is recommended you now install the MEI Drive (see

“MEI Driver” on page 7 - 34).

Windows Experience Index

After the drivers are installed follow this procedure to

ensure an accurate rating from the Windows Experi-

ence Index (make sure the AC/DC adapter is plugged

in):

1. Click Start, and click Control Panel.

2. Click Performance Information and Tools

(System and Security > System > Check the

Windows Experience Index).

3. Click “Rate this computer”.

4. The computer will take a few minutes to assess

the system performance.

5. Close the control panel.

Drivers & Utilities

4 - 8 Driver Installation

Optional Drivers

See the pages indicated for the driver installation pro-

cedures for any modules included in your purchase op-

tion.

Figure 4 - 2 - Drivers Installer - Option Drivers Menu



Windows Update

After installing all the drivers make sure you enable Win-

dows Update in order to get all the latest security up-

dates etc. (all updates will include the latest hotfixes

from Microsoft).

To enable Windows Update make sure you are con-

nected to the internet:

1. Click Start, and click Control Panel (or point

to Settings and click Control Panel).

2. Click Check for updates (Security), or

double-click Security Center and click

Windows Update.

3. Double-click Check for updates (button).

4. The computer will now check for updates

(you need to be connected to the internet).

5. Click Install now (button) to install the

updates.

Drivers & Utilities

Driver Installation 4 - 9

Bluetooth Module

Note: The operating system is the default setting for

Bluetooth control in Windows, and does not require a

driver. See “Bluetooth Module” on page 7 - 2 for con-

figuration instructions.

Wireless LAN Module

See the introduction in “Wireless LAN Module” on

page 7 - 7, and check the installation procedure.

PC Camera Module

See the introduction in “PC Camera Module” on

page 7 - 13, and check the installation procedure.

3.75G/HSPA Module

See the introduction in “PC Camera Module” on

page 7 - 13, and check the installation procedure.

Fingerprint Reader Module

See the introduction in “Fingerprint Reader Module”

on page 7 - 30, and check the installation procedure.

MEI Driver

See “MEI Driver” on page 7 - 34.

TPM Driver

See the introduction in “Trusted Platform Module”

on page 7 - 40, and check the installation procedure.

Drivers & Utilities

4-10

BIOS Utilities

Overview 5 - 1

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Setup utility

If your computer has never been set up, or you are making important changes to the

system (e.g. hard disk setup), then you should review this chapter first and note the

original settings found in Setup. Even if you are a beginner, keep a record of the set-

tings you find and any changes you make. This information could be useful if your

system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you

are doing. Many of the settings are required by the system, and changing them could

cause it to become unstable or worse. If you have any doubts, consult your service

representative.



BIOS Screens

Note that the BIOS

screens pictured on

these pages are intend-

ed for guidance in set-

ting up your system’s

BIOS.

BIOS versions are sub-

ject to constant change

and revision, therefore

your computer’s actual

screens may appear

slightly different from

those pictured on these

pages.

BIOS Utilities

5 - 2 The Power-On Self Test (POST)

The Power-On Self Test (POST)

Each time you turn on the computer, the system takes a few seconds to conduct a

POST, including a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong. If there

is a problem that prevents the system from booting, it will display a system summary

and prompt you to run Setup.

If there are no problems, the Setup prompt will disappear and the system will load

the operating system. Once that starts, you can’t get into Setup without rebooting.



POST Screen

1.BIOS information

2.CPU type

3.Memory status

4.Enter Setup prompt

appears only during

POST

Note:

The

POST

screen

as pictured right is for

guideline purposes only.

The

POST

screen on

your computer may ap-

pear slightly different. If

you disable the

Boot-

time Diagnostic Screen

the POST screen will not

appear.

Figure 5 - 1

POST Screen

BIOS Utilities

The Power-On Self Test (POST) 5 - 3

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and “non-

fatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously wrong

with your system. Take the computer to your service representative or authorized

service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying the

problem (make a note of this message!) followed by the prompt:

• Press <F1> to resume

• <F2> to enter Setup

Press F1 to see if the boot process can continue. It may work, without the correct

configuration.

Press F2 to run the Setup program and try to correct the problem. If you still get an

error message after you change the setting, or if the “cure” seems even worse, call

for help.

BIOS Utilities

5 - 4 Intel® vPro™ technology

Intel® vPro™ technology

Intel® vPro™ technology is supported by Model A computers only. This set of

technology features, built into the computer’s motherboard, allows Information

Technology departments remote access to the computer. This allows the IT depart-

ment to monitor, maintain and manage computers regardless of the state of the op-

erating system or the computer’s power state. This can be done over a wired or

corporate wireless network, or even outside the corporate firewall through a wired

LAN connection.

Accessing the Intel Management Engine

To access the Intel Management Engine press Ctrl + P at startup. Your system ad-

ministrator will need to assist you in managing the information as applicable to your

enterprise. Note the following password information for the Intel Management En-

gine:

• The default password is “admin” (without quotes).

If you get an "Error - Intel(R) ME password change rejected" message when cre-

ating a new password, then note the following parameters for creating a password:

• between 8 and 32 characters long

• Contain both upper and lower case Latin characters

• Have at least one numeric character

• Have at least one ASCII non-alphanumeric character (!, @, #, $,%, ^, &, *)

BIOS Utilities

Intel® vPro™ technology 5 - 5

Once you have entered the password you will then be taken to the platform config-

uration screen.

Figure 5 - 2

Intel(R) Management

Engine

(Password Creation)

BIOS Utilities

5 - 6 Intel® vPro™ technology

The platform configuration screen allows you to setup Intel ME as per your require-

ments (consult your IT administrator for the actual settings required).

Figure 5 - 3

Intel(R) Management

Engine

(Platform

Configuration)

BIOS Utilities

The Setup Program 5 - 7

The Setup Program

The Phoenix Setup program tells the system how to configure itself and manage ba-

sic features and subsystems (e.g. port configuration).

Entering Setup

To enter Setup, turn on the computer and press F2 during the POST. The prompt

(Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds

after you turn on the system. If you get a “Keyboard Error”, (usually because you

pressed F2 too quickly) just press F2 again.

If the computer is already on, reboot using the Ctrl + Alt + Delete combination and

then hold down F2 when prompted. The Setup main menu will appear.



BIOS Settings

Warning

Incorrect settings can

cause your system to

malfunction. To correct

mistakes, return to Set-

up and restore the Set-

up Defaults with <F9>.

BIOS Utilities

5 - 8 The Setup Program

Setup Screens

The following pages contain additional advice on portions of the Setup.

Along the top of the screen is a menu bar with menu headings. When you select a

heading, a new screen appears. Scroll through the features listed on each screen to

make changes to Setup.

Instructions on how to navigate each screen are in the box along the bottom of the

screen. If these tools are confusing, press F1 to call up a General Help screen, and

then use the arrow keys to scroll up or down the page.

The Item Specific Help on the right side of each screen explains the highlighted

item and has useful messages about its options.

If you see an arrow next to an item, press Enter to go to a sub-menu on that sub-

ject. The sub-menu screen that appears has a similar layout, but the Enter key may

execute a command.



Setup Menus

The Setup menus

shown in this section are

for reference only. Your

computer’s menus will

indicate the configura-

tion appropriate for your

model and options.

BIOS Utilities

Main Menu 5 - 9

Main Menu

System Time & Date (Main Menu)

The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you

can change the date and time settings in your operating system, you will also change

these settings. Some applications may also alter data files to reflect these changes.

Figure 5 - 4

Main Menu

BIOS Utilities

5 - 10 Main Menu

SATA Port 1/2/3/4 (Main Menu)

Pressing Enter opens the sub-menu to show the configuration of an HDD/optical de-

vice on the computer’s SATA Port 1/2/3/4. Use the Auto (Type:) setting to have the

items configured automatically for you.

System Memory/Extended Memory (Main Menu)

This item contains information on the system memory, and is not user configurable.

The system will auto detect the amount of memory installed.

BIOS Revision/KBC/EC Firmware Revision (Main Menu)

This item contains information on the current BIOS and firmware versions.

BIOS Utilities

Advanced Menu 5 - 11

Advanced Menu

Advanced Chipset Control

(see “Advanced Chipset Control Menu” on page 5 - 13)

The sub-menu here allows you to enable/disable some advanced system features.

Figure 5 - 5

Advanced Menu

BIOS Utilities

5 - 12 Advanced Menu

Legacy USB Support (Advanced Menu)

Use this menu item to enable/disable the support for Legacy Universal Serial Bus in

non-USB aware operating systems.

Boot-time Diagnostic Screen (Advanced Menu)

Use this menu item to enable/disable the Boot-time Diagnostic Screen or Power-On

Self Test (see “The Power-On Self Test (POST)” on page 5 - 2).

Legacy OS Boot: (Advanced Menu)

Enable this item to support only system boot from the Legacy OS (e.g Windows 7).

If disabled the system will attempt to boot from the EFI (Extensible Firmware Inter-

face) before the Legacy OS.

Power on Boot Beep (Advanced Menu)

Use this menu item to enable/disable the beep as the computer starts up.

Battery Low Alarm Beep (Advanced Menu)

Use this menu item to enable/disable the audible warning when the battery has

reached low power status.

BIOS Utilities

Advanced Chipset Control Menu 5 - 13

Advanced Chipset Control Menu

On Board JMicron Power Saving > Advanced Chipset Control

This item allows you to enable/disable JMicron Power Saving (as used by the card

reader) as a power saving measure.

Note that this item is applicable

to Model A Computers only.

Figure 5 - 6

Advanced Chipset

Control Menu

BIOS Utilities

5 - 14 Advanced Chipset Control Menu

Intel Trusted Execution > Advanced Chipset Control (Model A Only)

Intel(R) Trusted Execution Technology utilizes additional hardware capabilities to

protect the confidentiality and integrity of data stored or created on the system by

enabling an environment where applications can run within their own space, protect-

ed from all other software on the system. This can help protect vital data from being

attacked by malicious software running on the computer.

Intel Virtualization Technology > Advanced Chipset Control

Intel(R) Virtualization Technology enables a CPU to act as if it were several CPUs

working in parallel in order to allow several operating systems to run at the same

time in the same machine.

VT-d Technology > Advanced Chipset Control

Enable/Disable VT-d Technology (Virtualization Technology for directed I/O) from

this menu.

External Serial port > Advanced Chipset Control

Enable/Disable support for the docking station’s (RS232) serial port here.

SPI Flash Config Lock-Down > Advanced Chipset Control

Enable/Disable SPI (Serial Peripheral Interface) ROM Lock-Down here.

BIOS Utilities

Security Menu 5 - 15

Security Menu

Set Supervisor Password (Security Menu)

You can set a password for access to the PhoenixBIOS Setup Utility. This will not

affect access to the computer OS, (only the PhoenixBIOS Setup Utility).



Security Menu

The changes you

make here affect the

access to the Setup

utility itself, and also

access to your ma-

chine as it boots up af-

ter you turn it on.

These settings do not

affect your machine or

network passwords

which will be set in

your software OS.

Figure 5 - 7

Security Menu

BIOS Utilities

5 - 16 Security Menu

Set User Password (Security Menu)

You can set a password for user mode access to the PhoenixBIOS Setup Utility.

This will not affect access to the computer OS, (only the Setup utility) unless you

choose to set a Password on Boot (see below). Many menu items in the PhoenixBI-

OS Setup Utility cannot be modified in user mode. You can only set the user pass-

word after you have set the supervisor password.

Password on boot: (Security Menu)

Specify whether or not a password should be entered to boot the computer (you may

only set a password on boot if a supervisor password is enabled). If “Enabled”

is selected, only users who enter a correct password can boot the system (see the

warning in the sidebar). The default setting is “Disabled”.

Note: To clear existing passwords press Enter and type the existing password, then

press Enter for the new password (without typing any password entry) and Enter

again to confirm the password clearance.

TPM (Trusted Platform Module) Support: (Security Menu)

The TPM security chip allows you to create and manage digital certificates for user

and platform authentication. Enable TPM Support from this menu, and the TPM

State menu will then appear (see “TPM State” on page 5 - 17). Note: If you disable

TPM Support then your TPM information may be erased altogether. You should

only disable TPM support when you need to clear the TPM information. The default

setting is “Disabled”.



Password Warning

If you set a boot pass-

word (Password on boot

is “Enabled“), NEVER

forget your password.

The consequences of

this could be serious. If

you cannot remember

your boot password you

must contact your ven-

dor and you may lose all

of the information on

your hard disk.

TPM Password

Note that you should set

a supervisor password

in the BIOS to protect

the TPM information

from being tampered

with by unauthorized us-

ers.

BIOS Utilities

TPM State 5 - 17

TPM State

Change TPM State (TPM State)

This menu allows you to set the level of TPM functionality. You can enable/disable

the TPM function altogether, or clear all existing TPM information.

Note: If you clear all TPM information it will be erased altogether and the informa-

tion will need to be reconfigured.



TPM State Menu

To access this menu

you must first enable

TPM support from the

security menu (see

page 5 - 15).

Password

Protection

Note that you should set

a supervisor password

in the BIOS to protect

the TPM information

from being tampered

with by unauthorized us-

ers.

Figure 5 - 8

TPM State

BIOS Utilities

5 - 18 TPM State

If you have made any changes to the TPM State you will be asked to execute or reject

the changes made after you have saved and exited the BIOS. Highlight the required

option (it will be white), and then press Enter to save it.

See “Trusted Platform Module” on page 7 - 40 for more details.

Figure 5 - 9

Physical Presence

Operations

BIOS Utilities

Boot Menu 5 - 19

Boot Menu

When you turn the computer on it will look for an operating system (e.g. Windows

7) from the devices listed in this menu, and in this priority order. If it cannot find

the operating system on that device, it will try to load it from the next device in the

order specified in the Boot priority order. Item specific help on the right is avail-

able to help you move devices up and down the order.



BIOS Screens

Note that the BIOS

screens pictured on

these pages are intend-

ed for guidance in set-

ting up your system’s

BIOS.

BIOS versions are sub-

ject to constant change

and revision, therefore

your computer’s actual

screens may appear

slightly different from

those pictured on these

pages.

Figure 5 - 10

Boot Menu

BIOS Utilities

5 - 20 Exit Menu

Exit Menu

Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any

changes you have made to the Setup. You can also choose to restore the original Set-

up defaults that will return the Setup to its original state, and erase any previous

changes you have made in a previous session.

Figure 5 - 11

Exit Menu

Upgrading The Computer

Overview 6 - 1

Chapter 6: Upgrading The Computer

Overview

This chapter contains information on upgrading the computer. Follow the steps out-

lined to make the desired upgrades. If you have any trouble or problems you can con-

tact your service representative for further help. Before you begin you will need:

• A small crosshead or Phillips screwdriver

• A small regular slotted (flathead) screwdriver

• An antistatic wrist strap

Before working with the internal components you will need to wear an antistatic

wrist strap to ground yourself because static electricity may damage the compo-

nents.

The chapter includes:

• Removing the Battery

• Upgrading the Hard Disk Drive

• Upgrading the Optical (CD/DVD) Device

• Upgrading the System Memory (RAM)

Please make sure that you review each procedure before you perform it.



Warranty Warning

Please check with your

service representative

before undertaking any

upgrade procedures to

find out if this will VOID

your warranty.

Upgrading The Computer

6 - 2 Overview

When Not to Upgrade

These procedures involve opening the system’s case, adding and sometimes replac-

ing parts.

You should not perform any of these upgrades if:

• Your system is still under warranty or a service contract

• You don’t have all the necessary equipment

• You’re not in the correct environment

• You doubt your abilities

Under any of these conditions, contact your service representative to purchase or re-

place the component(s).

Upgrading the Processor

If you want to upgrade your computer by replacing the existing processor with a fast-

er/new one you will need to contact your customer service representative. We rec-

ommend that you do not do this yourself, since if it is done incorrectly you may

damage the processor or mainboard.



Power Safety

Warning

Before you undertake

any upgrade proce-

dures, make sure that

you have turned off the

power, and disconnect-

ed all peripherals and

cables (including tele-

phone lines). It is advis-

able to also remove your

battery in order to pre-

vent accidentally turning

the machine on.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember

to replace the cover(s) and screw(s) before turning the computer on.

Upgrading The Computer

Removing the Battery 6 - 3

Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety reasons

it is best to remove the battery.

1. Turn the computer off, and turn it over.

2. Slide the latch in the direction of the arrow.

3. Slide the latch in the direction of the arrow, and hold it in place.

4. Slide the battery out in the direction of the arrow .



Warranty Warning

Please check with your

service representative

before undertaking any

upgrade procedures to

find out if this will VOID

your warranty.

Figure 6 - 1

Battery Removal

Upgrading The Computer

6 - 4 Upgrading the Hard Disk Drive

Upgrading the Hard Disk Drive

The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard

disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow your

operating system’s installation instructions, and install all necessary drivers and util-

ities (see “Driver Installation” on page 4 - 2), when setting up a new hard disk.

1. Turn off the computer, and turn it over and remove the battery.

2. Locate the hard disk bay cover and loosen screws & .

3. Remove the hard disk bay cover .



HDD System

Warning

New HDD’s are blank. Be-

fore you begin make sure:

You have backed up any

data you want to keep from

your old HDD.

You have all the CD-ROMs

and FDDs required to in-

stall your operating system

and programs.

If you have access to the in-

ternet, download the latest

application and hardware

driver updates for the oper-

ating system you plan to in-

stall. Copy these to a

removable medium.

Figure 6 - 2

Hard Disk Bay

Cover Removal

Upgrading The Computer

Upgrading the Hard Disk Drive 6 - 5

4. Grip the tab and slide the hard disk in the direction of arrow .

5. Lift the hard disk out of the bay .

6. Remove the screw(s) and the adhesive cover .

7. Reverse the process to install a new hard disk drive (do not forget to replace all the

screws and covers).

Figure 6 - 3

HDD Assembly

Removal

Figure 6 - 4

HDD Cover

Removal



Hard Disk Screws & Cover

The hard disks and covers pictured

here may appear slightly different from

your model design (these designs are

subject to change and upgrade without

notice). Pay careful attention to the

screws (if included) and cover orienta-

tion.

Upgrading The Computer

6 - 6 Upgrading the Optical (CD/DVD) Device

Upgrading the Optical (CD/DVD) Device

1. Turn off the computer, and turn it over and remove the battery.

2. Locate the hard disk bay cover and loosen screws & .

3. Remove the hard disk bay cover .

Figure 6 - 5

Removing the HDD

Cover

Upgrading The Computer

Upgrading the Optical (CD/DVD) Device 6 - 7

4. Remove the screw at point , and use a screwdriver to carefully push out the

optical device at point .

5. Reverse the process to install the new device.

Figure 6 - 6

Removing the

Optical Device

Upgrading The Computer

6 - 8 Upgrading the System Memory (RAM)

Upgrading the System Memory (RAM)

The computer has two memory sockets for 204 pin Small Outline Dual In-line (SO-

DIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 2 for

details of supported module types).

1. Turn off the computer, and turn it over and remove the battery.

2. Locate the RAM & CPU bay cover and remove screws

- .

Figure 6 - 7

CPU/RAM Bay

Cover Screws

Upgrading The Computer

Upgrading the System Memory (RAM) 6 - 9

3. Carefully (a fan and cable are attached to the under side of the cover) lift up

the bay cover.

4. Carefully disconnect the fan cable , and remove the cover

5. Gently pull the two release latches on the sides of the memory socket in the

direction indicated by the arrows ( &

) in Figure 6 - 10.



Fan Cable & Cover

Make sure you reconnect

the fan cable before

screwing down the bay cov-

er. Note the information on

replacing the RAM & CPU

bay cover in

“Cover

Pins” on page 6 - 11.

Figure 6 - 8

CPU/RAM Bay

Cover Removed

Figure 6 - 9

RAM Module

Release



Contact Warning

Be careful not to touch the metal pins on the

RAM module’s connecting edge. Even the

cleanest hands have oils which can attract

particles, and degrade the module’s perfor-

mance.

Upgrading The Computer

6 - 10 Upgrading the System Memory (RAM)

6. The RAM module will pop-up, and you can remove it.

7. Pull the latches to release the second module if necessary.

8. Insert a new module holding it at about a 30° angle and fit the connectors firmly

into the memory slot.

9. The module’s pin alignment will allow it to only fit one way. Make sure the module

is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit

without much pressure.

10. Press the module in and down towards the mainboard until the slot levers click into

place to secure the module.

Figure 6 - 10

RAM Module

Removal



Single Memory

Module Installation

If your computer has a

single memory module,

then insert the module

into the Channel 0

(JDIMM1) socket. In this

case this is the lower

memory socket (the

socket closest to the

mainboard).

Upgrading The Computer

Upgrading the System Memory (RAM) 6 - 11

11. Replace the bay cover and screws (make sure you reconnect the fan cable

before screwing down the bay cover).

12. Restart the computer to allow the BIOS to register the new memory configuration

as it starts up.



Cover Pins

Note that there are cov-

er pins need to be

aligned with slots in the

case to insure a proper

cover fit, before screw-

ing down the bay cover

(see Figure 6 - 11).

Figure 6 - 11

Cover Pin

Alignment

Upgrading The Computer

6-12

Modules & Options

Overview 7 - 1

Chapter 7: Modules & Options

Overview

This chapter contains information on the following modules, which may come with

your computer, depending on the configuration purchased. If you are unsure please

contact your service representative.

• Bluetooth Module

• Wireless LAN Module

• PC Camera Module

• 3.75G/HSPA Module

• Fingerprint Reader Module

•MEI Driver

• Trusted Platform Module



Wireless Device

Operation Aboard

Aircraft

The use of any portable

electronic transmission de-

vices aboard aircraft is usu-

ally prohibited. Make sure

the module(s) are OFF if

you are using the computer

aboard aircraft.



Important Notice - 3.75G/HSPA & Bluetooth/

Wireless LAN Modules

If your purchase option includes both Wireless LAN and

3.75G modules, then the appropriate antennas will be in-

stalled. Note that In order to comply with FCC RF exposure

compliance requirements, the antenna must not be co-locat-

ed or operate in conjunction with any other antenna or trans-

mitter.

In order to comply with FCC regulations you should NOT

operate the 3.75G/HSPA module and the Bluetooth/Wire-

less LAN modules at the same time as this may disrupt ra-

dio frequency, and cause interference.

When the 3.75G/HSPA module is powered on, make sure

that the Bluetooth/Wireless LAN modules are powered off.

Modules & Options

7 - 2 Bluetooth Module

Bluetooth Module

The operating system’s Bluetooth Devices control panel is used to configure the

Bluetooth settings in Windows, and therefore does not require a driver. Use the Fn

+ F12 key combination (see “Function/Hot Key Indicators” on page 1 - 10) to

toggle power to the Bluetooth module. When the Bluetooth module is powered on,

the LED will be orange and the

on-screen indicator

will briefly be

displayed.



Wireless Device

Operation Aboard

Aircraft

The use of any portable

electronic transmission de-

vices aboard aircraft is usu-

ally prohibited. Make sure

the module(s) are OFF if

you are using the computer

aboard aircraft.

Use the Fn + F12 key com-

bination to toggle power to

the Bluetooth module, and

check the LED indicator to

see if the module is pow-

ered on or not (see Table 1

- 5, on page 1 - 10/ Table 1

- 3, on page 1 - 7).



Bluetooth Data Transfer

Note that the transfer of data between the computer and a Bluetooth enabled device is sup-

ported in one direction only (simultaneous data transfer is not supported). Therefore

if you are copying a file from your computer to a Bluetooth enabled device, you will not be

able to copy a file from the Bluetooth enabled device to your computer until the file transfer

process from the computer has been completed.

Bluetooth Module & Resuming From Sleep Mode

The Bluetooth module’s default state will be off after resuming from the Sleep power-saving

state. Use the key combination (Fn + F12) to power on the Bluetooth module after the com-

puter resumes from Sleep.

Modules & Options

Bluetooth Module 7 - 3

Bluetooth Configuration in Windows 7

Setup your Bluetooth Device so the Computer Can Find it

1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on.

2. Make the device discoverable (to do this check your device documentation).

To Turn the Bluetooth Module On

1. Press the Fn + F12 key combination to power on the Bluetooth module.

2. A Bluetooth icon will appear in the taskbar.

3. You can then do any of the following to access the Bluetooth Devices control

panel.

• Double-click the taskbar icon to access the Bluetooth Devices control panel.

• Click/Right-click the taskbar icon and choose an option from the menu.



Add a Device

Click Start, and click

Control Panel and then

click Devices and

Printers (Hardware

and Sound). Click Add

a device to search for

any available Bluetooth

devices.

Figure 7 - 1

Bluetooth Devices &

Click Icon Menu

Add a device

Right-Click Taskbar Icon

Modules & Options

7 - 4 Bluetooth Module

To Add a Bluetooth Device

1. Access the Bluetooth Devices control panel and click Add a device.

2. Double-click the device you want to pair with the computer.

3. On first connection the computer will provide you with a pairing code to be entered

onto the device.



Pairing Options

If a device has been pre-

viously connected then

the pairing option menu

will appear when you at-

tempt subsequent con-

nections. You can choose

to have the computer cre-

ate a pairing code for you,

use the device’s existing

pairing code or you can

pair certain devices with-

out using a code.

Figure 7 - 2

Add a Device

Modules & Options

Bluetooth Module 7 - 5

4. Enter the code into your Bluetooth enabled device and follow any on-screen

instructions to complete the pairing.

5. Windows will check to see if any drivers are required to complete the pairing.

6. Follow any on-screen instructions on the computer if device drivers are required to

be installed.

7. Click Close.

Figure 7 - 3

Pairing Code

Example

Figure 7 - 4

Pairing Complete &

Bluetooth Device

Enabled



Pairing Codes

The example outlined here shows a connection to

a mobile device. Other devices e.g. computers,

may have a slightly different connection proce-

dure, and may require you to confirm a pairing

code is correct on both devices. Follow the on-

screen instructions to complete the pairing.

Modules & Options

7 - 6 Bluetooth Module

To Change Settings for the Bluetooth Device

1. Click the taskbar icon and select Show Bluetooth Devices.

2. Right-click on the device you want to change and click Properties to:

• Change the name of the device (click Bluetooth, type a new name and click OK).

• Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK).

To Make your Computer Discoverable to Bluetooth Devices

1. Click the taskbar icon and select Open Settings.

2. Click Options, and make sure that Allow Bluetooth devices to find this

computer check box (Discovery) has a tick inside it.

3. Make sure that the Alert me when a new Bluetooth device wants to connect

check box (Connections) has a tick inside it, if you want to be notified when a

Bluetooth device wants to connect.



Bluetooth Help

To get help on Bluetooth

configuration and set-

tings, select

Help and

Support

from the

Start

menu. Type Bluetooth in

the

Search Help

box, and

select an item from the re-

turned search results to

get more information.

Figure 7 - 5

Bluetooth Settings -

Options

Modules & Options

Wireless LAN Module 7 - 7

Wireless LAN Module

If you have included an

Intel

Wi-Fi Link 6200/6300 Series or 3rd Party 802.11b/

g/n WLAN

module in your purchase option, make sure that the Wireless LAN mod-

ule is on b

efore installing the driver.

Use the

Fn + F11 key combination

(see

“Function/Hot Key Indicators” on page 1

- 10

)

to toggle power to the Wireless LAN module

. When the WLAN module is

powered on, the LED will be

green

and the on-screen indicator will

briefly be displayed. Make sure you install the drivers in the order indicated in

Table 4

- 1, on page 4 - 3

Wireless should be turned ON in the Windows Mobility Center to ensure proper

wireless function key behavior (see “Windows Mobility Center” on page 7 - 12).



Wireless Device

Operation Aboard

Aircraft

The use of any portable

electronic transmission de-

vices aboard aircraft is usu-

ally prohibited. Make sure

the module(s) are OFF if

you are using the computer

aboard aircraft.

Use the Fn + F11 key com-

bination to toggle power to

the WLAN module, and

check the indicator to see if

the module is powered on

or not (see Table 1 - 5, on

page 1 - 10/ Table 1 - 3, on

page 1 - 7).

Modules & Options

7 - 8 Wireless LAN Module

Intel® Wi-Fi Link Series Driver Installation

If you see the message “Found New Hardware” click Cancel to close the window.

1. Make sure the module is powered on, and then insert the Device Drivers &

Utilities + User’s Manual disc into the CD/DVD drive.

2. Click Option Drivers (button).

3. Click 1.Install WLAN Driver > Yes.

4. Click Next > Next.

5. Click the button to accept the license and click Next.

6. Click Next > Next > Finish.

3rd Party 802.11b/g/n Driver Installation (Model B Only)

If you see the message “Found New Hardware” click Cancel to close the window.

1. Make sure the module is powered on, then insert the Device Drivers & Util-

ities + User’s Manual disc into the CD/DVD drive.

2. Click Option Drivers (button).

3. Click 1.Install WLAN Driver > Yes.

4. Choose the language you prefer and click Next.

5. Click Next > Install.

6. Click Finish to restart the computer.

Note: The operating system is the default setting for Wireless LAN control in Win-

dows.

Modules & Options

Wireless LAN Module 7 - 9

Connecting to a Wireless Network in Windows 7

Make sure the Wireless LAN module is turned on.

1. Click the taskbar wireless icon , and then double-click an access point to con-

nect to or click to Open Network and Sharing Center if you do not see a network

you want to connect to in the taskbar menu (a list of options will appear allowing

setting changes, and creating a new network).



Network and

Sharing Center

You can also use the

Net-

work and Sharing Cen-

ter

control panel in

Windows (

Network and

Internet

) to connect to

any available wireless

networks.

Figure 7 - 6

Click Taskbar Icon

Menu & Network

and Sharing Center

Modules & Options

7 - 10 Wireless LAN Module

2. You may need to enter a security key for any access point to which you are trying

to connect.

3. Click to select a network location (e.g. Home, Work or Public).

4. Click “View or change settings in Network and Sharing Center” to access

further options for the connection.

Figure 7 - 7

Network Location

Set

Modules & Options

Wireless LAN Module 7 - 11

5. Click the taskbar icon to see any currently connected networks.

6. To disconnect from the wireless network you can click the taskbar wireless icon

, click the active connection and then click Disconnect (button).



Security Enabled

Networks

You should try to make

sure that any network you

are connecting to is a se-

cure network.

Connecting to unsecure

networks may allow unau-

thorized access to your

computer, documents,

websites and files etc.

Figure 7 - 8

Click Taskbar Icon

Menu - Disconnect

Modules & Options

7 - 12 Wireless LAN Module

Windows Mobility Center

The Windows Mobility Center control panel provides an easy point of access for

information on battery status, power plans used and wireless device status etc.

To access the Windows Mobility Center:

1. Click Start, and click Control Panel (or point to Settings and click Control

Panel).

2. Double-click Windows Mobility Center (Mobile PC).

3. Click the button to Turn wireless off/on, or click the icon to access the network

menu.



Wireless Hot Keys

The computer’s wireless

function keys will not func-

tion properly if Wireless is

turned OFF in the Win-

dows Mobility Center

control panel.

The wireless indicators

may show that

the WLAN module is pow-

ered on, however if wire-

less is OFF in the Mobility

Center, the module will not

be powered on.

Make sure that Wireless is

ON in the Mobility Center to

ensure proper function key

behavior.

Figure 7 - 9

Windows Mobility

Center

Make sure Wireless is ON to ensure proper function key behavior.

Modules & Options

PC Camera Module 7 - 13

PC Camera Module

Make sure that the PC Camera module is on b

efore installing the driver and

use the

Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 10) to

toggle power to the PC Camera module. When the PC Camera module is powered

on, the on-screen indicator will briefly be displayed. Make sure you install the driv-

ers in the order indicated in Table 4 - 1, on page 4 - 3. When the PC Camera module

is powered on, the indicator will briefly be displayed.

There are a number of different camera modules available with this computer model

series. You will have the appropriate application installed for your camera (note

that some versions of the camera application do not support the zoom function).

Make sure you access the application via the desktop shortcut



Latest PC Camera

Driver Information

Check the Device Driv-

ers & Utilities + User’s

Manual disc, and any

accompanying insert

pages, for the latest up-

dated information on the

PC Camera driver,

which may override the

information provided

here.

PC Camera Driver

Uninstallation

If you need to uninstall

the driver, then uninstall

the WebCam Installer

item from the Programs

and Features control

panel in Windows.

Modules & Options

7 - 14 PC Camera Module

PC Camera Driver Installation

1. Make sure the module is powered on, and then insert the Device Drivers &

Utilities + User’s Manual disc into the CD/DVD drive.

2. Click Option Drivers (button).

3. Click 2.Install Webcam Driver > Yes.

4. Choose the language you prefer and click Next > Next > Finish.

Click Next > Next > Install > Finish to restart the computer.

Choose the language you prefer and click Next > Next > Finish to restart

the computer.

Click Next > Install > Finish > Finish to restart the computer.

5. Run the camera application program from the desktop shortcut (if the hard-

ware is turned off use the Fn + F10 key combination to turn it on again).



PC Camera Screen

Refresh

The PC Camera module

supports a frame rate of

12 fps. If you find that

the screen refresh rate

is subject to lag or stut-

tering, then reduce the

window size, or adjust

the Output Size and/or

Color Space Compres-

sion.

To reduce Output Size

and/or Color Space

Compression run the

camera application,

click Options and select

Video Capture Pin. Ad-

just the settings from the

appropriate pull-down

menu.

Modules & Options

PC Camera Module 7 - 15

PC Camera Audio Setup

If you wish to capture video & audio with your camera, it is necessary to setup the

audio recording options in Windows.

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

2. Click Sound (Hardware and Sound).

3. Click Recording (tab).

4. Right-click Microphone (Realtek High Definition Audio) and make sure the item is

not disabled.

5. Double-click Microphone (or select Properties from the right-click menu).

6. Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to

the level required.

7. Click OK and close the control panels.

8. Run the camera application program from the desktop shortcut.

9. Go to the Devices menu heading and select Microphone (Realtek High

Defini....) (it should have a tick alongside it).

10. Go to the Capture menu heading and select Capture Audio (it should have a tick

alongside it).

Modules & Options

7 - 16 PC Camera Module

Camera Application

The camera application is a video viewer for general purpose video viewing and test-

ing, and for capturing video files to .avi format.

1. Run the camera application from the desktop shortcut (it is recommended that you

set the capture file before the capture process - see “Set Capture File” on

page 7 - 16).

2. Go to the Capture menu heading (if you wish to capture audio check “PC Camera

Audio Setup” on page 7 - 15) and select Start Capture.

3. Click OK/Yes (the file location will be displayed in the pop-up box) to start

capturing the video, and press Esc to stop the capture (you can view the file using

the Windows Media Player).

Set Capture File

Prior to capturing video files you may select the Set Capture File... option in the

File menu, and set the file name and location before capture (this will help avoid ac-

cidentally overwriting files). Set the name and location then click Open, then set the

"Capture file size:"

and click OK. You can then start the capture process as on the

previous page.

Note the important information in reducing video file size below in order to

save file space, and help prevent system problems.



Pre-Allocating File

Size/Space

You may pre-allocate the

file size (

File > Allocate

File Size/Space

) for the

capture file in the

camera

program (you may need

to set a folder location

first).

Pre-allocating space on

the hard disk can improve

the capture quality (par-

ticularly of large capture

files), by reducing the

amount of work the hard

disk has to do in finding

space for the video data

as it is being captured.

See also

“Reducing Vid-

eo File Size” on page 7 -

Modules & Options

PC Camera Module 7 - 17

Reducing Video File Size

Note that capturing high resolution video files requires a substantial amount of disk

space for each file. After recording video, check the video file size (right-click the

file and select Properties) and the remaining free space on your hard disk (go to My

Computer, right-click the hard disk, and select Properties). If necessary you can

remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash

drive.

Note that the Windows 7 system requires a minimum of 15GB of free space on the

C: drive system partition. In order to prevent system problems it is recommended

that you save the captured video file to a location other than the C: drive (see set

capture file above), limit the file size of the captured video (see “Pre-Allocating File

Size/Space” on page 7 - 16) or reduce video resolution (see below).

To Reduce Video Resolution Output Size:

1. Run the camera application program from the desktop shortcut.

2. Go to Options and scroll down to select Video Capture Pin....

3. Click the Output Size drop box and select a lower resolution size in order to

reduce the captured file size.

4. Click OK.

Modules & Options

7 - 18 PC Camera Module

Eliminating Screen Flicker

If you find that the video screen in the camera program is flickering, you can try to

adjust the setting in the Video Capture Filter options.

1. Run the camera application from the desktop shortcut.

2. Go to Options and scroll down to select Video Capture Filter....

3. Click either 50Hz or 60Hz under Anti Flicker/Frequency/Powerline Frequency.



Latest PC Camera

Driver Information

Check the Device Driv-

ers & Utilities + User’s

Manual disc, and any

accompanying insert

pages, for the latest up-

dated information on the

PC Camera driver,

which may override the

information provided

here, including the fig-

ures pictured.

Figure 7 - 10

Video Capture Filter

Modules & Options

PC Camera Module 7 - 19

Zoom (if applicable)

The WebCam program allows you to zoom the camera in and out (note the zoom

function is not available in all camera model applications).

1. Run the camera application from the desktop shortcut.

2. Go to Zoom and select Zoom Out/Zoom In.

Taking Still Pictures

The WebCam program allows you to take still pictures.

1. Run the camera application from the desktop shortcut.

2. Go to Options and select Take Picture.

3. The picture (in JPEG format) will be placed in the Snapshot folder on the

desktop.

Figure 7 - 11

Zoom/Setting



Snapshot Folder

The Snapshot folder’s

default location is on the

desktop. Do not move

this folder or an error

may appear when you

try to take a still picture.

If you accidentally de-

lete or move the folder,

you can create a new

Snapshot folder on the

desktop in order to cap-

ture the files.

Modules & Options

7 - 20 3.75G/HSPA Module

3.75G/HSPA Module

If you have included an optional 3.75G/HSPA (High Speed Packet Access) module

(see “Communication” on page C - 4 for specification details) in your purchase op-

tion, you will have the appropriate application provided for your particular module.

Follow the instructions on page 7 - 22 to install the USIM card (supplied by your

service provider), and then install the application (see over for further details).



Important Notice - 3.75G/HSPA & Bluetooth/Wireless LAN Modules

In order to comply with FCC regulations you should NOT operate the 3.75G/HSPA module

and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio fre-

quency, and cause interference. When the 3.75G/HSPA module is powered on, make sure

that the Bluetooth/Wireless LAN modules are powered off.

Modules & Options

3.75G/HSPA Module 7 - 21

Before installing the application, make sure that the 3.75G/HSPA module is ON

(installing the driver with the module off will not allow the software to detect the

module hardware correctly). Use the Fn + key combination (see “Function/Hot

Key Indicators” on page 1 - 10) to toggle power to the 3.75G/HSPA module.

When the

3.75G/HSPA

module is powered on, the on-screen indicator will briefly be

displayed. Make sure you install the drivers in the order indicated in

Table 4 - 1, on

page 4 - 3

Note that exiting the application does NOT turn off the 3.75G/HSPA

module.

• Mobile Partner - See “Mobile Partner Application Installation” on page 7 -

23 for driver installation information and “Mobile Partner Application Installa-

tion” on page 7 - 23 for instructions on using the Mobile Partner application.



3.75G/HSPA

Modules & System

Wake Up

Note that the 3.75G mod-

ules

DO NOT

support

system wake up on

3.75G/HSPA modem ac-

tivity.

Modules & Options

7 - 22 3.75G/HSPA Module

3.75G/HSPA Module USIM Card Installation

Follow the instructions below to install the USIM card (which will be provided by

your service provider).

1. Turn off the computer, and turn it over.

2. Slide the latch in the direction of the arrow.

3. Slide the latch in the direction of the arrow, and hold it in place.

4. Remove the battery.

5. Insert the USIM card as illustrated below until it clicks fully into position, and

replace the battery.



Power Safety

Warning

Before you undertake any

installation procedures,

make sure that you have

turned off the power, and

disconnected all peripher-

als and cables (including

telephone lines).

USIM Card Orientation

Note that the USIM card’s

readable side (with the

gold-colored contacts)

should face upwards as il-

lustrated.

Figure 7 - 12

Battery Removal &

USIM Card Insertion

Modules & Options

3.75G/HSPA Module 7 - 23

Mobile Partner

With the 3.75G/HSPA module and USIM card (supplied by your service provider)

installed you may then install the Mobile Partner application. The Mobile Partner

application allows you to directly access your HSPA internet service from the com-

puter.

Mobile Partner Application Installation

1. Enable power to the module by pressing the Fn + key combination (give

the module about 10 seconds to power on and the on-screen icon will

indicate the module’s power status).

2. If a Found New Hardware window appears, click Cancel in all windows

that appear, and then proceed to install the driver as below.

3. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

4. Click Option Drivers (button).

5. Click

3.Install 3G Driver

> Yes

6. Choose the language you prefer and click OK.

7. Click Next > I Agree (button) to accept the license agreement.

8. Click Next > Install.

9. Click Finish to restart the computer.

10. Access the Mobile Partner application from the Start menu (Start > Pro-

grams/All Programs > Mobile Partner), or by double-clicking the Mobile

Partner icon on the desktop.



Wireless Device

Operation Aboard

Aircraft

The use of any portable

electronic transmission de-

vices aboard aircraft is usu-

ally prohibited. Make sure

the module(s) are OFF if

you are using the computer

aboard aircraft.

Use the Fn + key com-

bination to toggle power to

the 3.75G/HSPA module,

and check the indicator to

see if the module is pow-

ered on or not (see Table 1

- 5, on page 1 - 10/ Table 1

- 3, on page 1 - 7).

Modules & Options

7 - 24 3.75G/HSPA Module

Mobile Partner Application

You will need to contact your service provider to obtain the exact details of how ex-

actly to configure the settings on this page.

Profile Management

1. Power on the 3.75G/HSPA module using the Fn + key combination.

2. Access the Mobile Partner application from the Start menu (Start > Programs/

All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon

on the desktop .

3. If you have not created a profile, click Tools and select Options, and then click

Profile Management.

4. Click New and input the appropriate information for Profile Name, APN

and Authentication etc. as supplied by your service provider.

5. Click Save to save the profile.



Mobile Partner Help

To get help on Mobile

Partner configuration

and settings, click the

Help menu and select

Online Help or press

F1.

Figure 7 - 13

Profile Management

Modules & Options

3.75G/HSPA Module 7 - 25

Connecting to the Service Provider

1. Power on the 3.75G/HSPA module using the Fn + key combination.

2. Access the Mobile Partner application from the Start menu (Start > Programs/

All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon

on the desktop .

3. The software will run and you can select the Profile Name from the menu.

4. Click Connect to begin the connection process.

5. The Mobile Partner application will then display the connection information.

Figure 7 - 14

Connect

Figure 7 - 15

Network

Connection Prompt

Modules & Options

7 - 26 3.75G/HSPA Module

6. When the connection is successful you can move the cursor over the network icon

in the taskbar to display the connection information.

7. You can then access the internet, download e-mail etc. as per any internet

connection.

8. While you are connected the indicators in the Mobile Partner window will display

uploading and downloading icons and a network icon in the taskbar .

9. To disconnect click the Disconnect icon, or right click the taskbar icon

and select Disconnect.

10. The program will disconnect from the service provider.

Figure 7 - 16

Connected

Taskbar

Notification

Figure 7 - 17

Disconnect

Modules & Options

3.75G/HSPA Module 7 - 27

11. The module will still be on, and you will need to press the Fn + key combination

to turn it off.

12. If you click the Mobile Partner close icon a message will be displayed asking

you to click OK to confirm the program exit and to terminate the connection.

13. Exiting the program terminates the connection, but DOES NOT turn off the 3.75G/

HSPA module, and you will need to press the Fn +

key combination to turn off

the module (pay careful attention to this aboard aircraft - see “Wireless Device

Operation Aboard Aircraft” on page 7 - 23).

14. If the module is on and the computer enters a power-saving state, then the power

status of the module on resuming from the power-saving state will be as below:

• If the 3.75G/HSPA module is on and the computer is Shut Down or Restarted;

the module will be off when the computer starts up.

• If the 3.75G/HSPA module is on and the computer enters Sleep or Hibernate;

the module will be off when the computer resumes from sleep.

Figure 7 - 18

Exit Prompt

Modules & Options

7 - 28 3.75G/HSPA Module

Text Messaging Service

In addition to standard internet services you may also send and receive SMS text

messages using the Mobile Partner program, if your service supports SMS.

Reading SMS Messages

1. An icon will blink at the bottom of the Mobile Partner interface to notify you of

any new messages received.

2. Click the Text icon in the Mobile Partner Interface.

3. Select the Local > Inbox or SIM/USIM Card folder and select any message to

read it.

4. Right-click the message and choose an option to reply, forward or delete the

message.

Creating and Sending SMS Messages

1. Click the Text icon in the Mobile Partner Interface.

2. Click the New button .

3. Enter the recipient’s number in the Send To... field or click the Send To... button to

select an entry from the phone book, and click OK.

4. Type in the message details.

5. Click the Send button, Save button to send the message later or Close > Yes to

save in the Draft folder.

For more details on SMS click the Help menu and select Online Help or press F1

and select SMS.

Modules & Options

Security Modules (Fingerprint & TPM) 7 - 29

Security Modules (Fingerprint & TPM)

The encrypted channel between the Trusted Platform Module security chip and

the fingerprint reader with Protector Suite Software provides a high level of se-

curity for your computer. A further level of security and control is provided in the

BIOS (see “Security Menu” on page 5 - 15 and “TPM State” on page 5 - 17).

The fingerprint reader with the Protector Suite Software allows you to:

• Access or Lock your computer

• Protect sensitive files

• Display and file your favorite web pages

• Fill in frequently used dialogs

• Run your favorite applications

The TPM security chip allows you to create and manage digital certificates for user

and platform authentication. This type of security is usually administered within

large enterprises and organizations, and therefore requires implementation by a sys-

tem administrator before users can access security features.

Individual users can use the TPM as an authentication with the fingerprint reader.

Make sure you have administrator’s rights to your computer, and have a Windows

password enabled for full security protection. In addition Make sure you prepare

a removable media (e.g. a USB flash drive) to store passwords etc. before begin-

ning the TPM initialization process.



Password Warning

If you set passwords for

any of the security mod-

ules, NEVER forget your

password.

The consequences of

this could be serious. If

you cannot remember

your boot password you

must contact your ven-

dor and you may lose all

of the information on

your hard disk.

Modules & Options

7 - 30 Fingerprint Reader Module

Fingerprint Reader Module

The fingerprint reader module provides a high level of security for your computer.

Make sure you have administrator’s rights to your computer, and have a Windows

password enabled for full security protection.

Before beginning the enrollment process it is recommended that you go through the

fingerprint tutorial. To run the tutorial click Start > Programs/All Programs >

Protector Suite QL > Fingerprint Tutorial after installing the driver.

Fingerprint Reader Driver Installation

1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3. Click 4.Install Fingerprint Driver > Yes.

4. Click Next > Next > Next.

5. Click Finish > Yes to restart the computer.



Help & Manual

Right-click the taskbar icon

to bring up the menu to

select Help.

Modules & Options

Fingerprint Reader Module 7 - 31

User Enrollment

1. Click Start > Programs/All Programs > Protector Suite > Control Center, or

double click the taskbar icon (click Initialize).

2. On the first run of the program you will be asked to click the Accept button to

accept the license.

3. If you have not set a Windows password you will be prompted to do so (note: If

you have not set a password Protector Suite cannot secure access to your

computer).

4. Click Submit when you have entered password.

5. You will then be prompted to enroll your fingerprints (you can click Tutorial to get

help with fingerprint enrollment at any time).



Fingerprint

Enrollment

Note that it is strongly rec-

ommended that you enroll

more than one finger in

case of injury etc.

Figure 7 - 19

Fingerprint

Enrollment

Tutorial

Modules & Options

7 - 32 Fingerprint Reader Module

6. Click the button above any of the fingers to begin the enrollment process for that

finger.

7. Swipe the finger until the progress bar reaches 100% to enroll that finger.

8. Close the Protector Suite 2009 window.

9. Right-click the taskbar icon and select Start Control Center (and then swipe a

finger) to allow you to Edit Fingerprints, register Applications, edit Settings and

access the Help menu etc. You can also run the Control Center etc. from the

Protector Suite item in the Programs/All Programs menu

10. Click “Help” in Control Center Home to get more information on any topic.

11. You can also run the Tutorial, or Product Tour video to get more information.

12. See “Help & Manual” on page 7 - 30 for further details.

13. If you swipe your finger over the reader at any time you can access the Biomenu

to lock the computer, register websites, access the Personal Safe, open the

Control Center and access the Help menu.

Help

Figure 7 - 20

Control Center &

Biomenu

Modules & Options

Fingerprint Reader Module 7 - 33

Fingerprint Control Center Features

Application Launcher

The Application Launcher allows you to register applications to be launched when

assigned to a particular finger. Simply copy the application icon on to one of the reg-

istered fingers and ten click OK to close the application window. Once registered the

application will launch when you swipe the appropriate finger across the sensor.

Password Bank

The Password Bank stores registrations of user names, passwords and other set-

tings for web sites etc.

File Safe

File Safe is an encrypted area assigned on your hard drive that allows you to store

files and folders to be protected by fingerprint protection.



Help

For more information on

these and other features

simply access “

Help

” in

the

Fingerprint Control

Center

and select the

item from the menu on

the left.

Modules & Options

7 - 34 MEI Driver

MEI Driver

1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3. Click 5.Install MEI Driver > Yes.

4. Click Next (for Model A computers you may click in the checkbox to select

“Install Intel® Control Center”).*

5. Click Yes > Next > Next.

6. Click Finish.

* The Intel® Control Center provides a central starting point for Intel applications

to make it easier to find programs required (Model A only). Access the Intel® Con-

trol Center from the Start > Programs/All Programs > Intel > Inte® Control

Center.

Modules & Options

MEI Driver 7 - 35

Intel® Management and Security Status

(Model A Only)

Access the Intel

® Management and Security Status control panels from the Start

menu in Windows. These features allow users and IT Administrators to enhance

and protect computing assets. Your system administrator will need to assist you in

managing some of the information here.

Figure 7 - 21

Intel Management &

Security Status Help



User Guide

You can access the user guide provid-

ed to get help on any aspect of the In-

tel® Management and Security Status

control panel.

Click on Learn More at the bottom left

of the control panel and then click “For

more information, refer to the user

guide” (link).

You will need to have the Adobe Acro-

bat Reader program installed (this is

provided on the Device Drivers & Util-

ities + User’s Manual disc.

Modules & Options

7 - 36 MEI Driver

General

The General tab provides basic information on Intel® AMT, Intel® Standard Man-

ageability, Level 3 Manageability Upgrade, Intel® Anti-Theft and Intel® RPAT sta-

tus and events.

Figure 7 - 22

Intel Management &

Security Status

General

Modules & Options

MEI Driver 7 - 37

Intel® Active Management Technology

The Intel® AMT tab will be shown if you system is configured to support it. This

allows your network’s IT professionals to remotely discover, heal and protect your

computer.

Figure 7 - 23

Intel Management &

Security Status

Intel® AMT

Modules & Options

7 - 38 MEI Driver

Intel® Anti-Theft

This tab displays information on Intel® Anti-Theft information. Click on the link to

connect to an Intel site to get more information on Intel® Anti-Theft technology.

Figure 7 - 24

Intel Management &

Security Status

Intel® Anti-Theft

Modules & Options

MEI Driver 7 - 39

Advanced

The Advanced tab provides additional information on the system.

Figure 7 - 25

Intel Management &

Security Status

Advanced

For Intel PRO Wireless 2200BG

Modules & Options

7 - 40 Trusted Platform Module

Trusted Platform Module

Before setting up the TPM functions you must initialize the security platform.

Initializing TPM

1. Restart the computer.

2. Enter the Phoenix SecureCore(tm) Setup Utility by pressing F2 during the

POST.

3. Use the arrow keys to select the Security menu.

4. Select TPM Support and set the item to Enabled.

5. The TPM State menu will then appear.

Figure 7 - 26

TPM Support

Modules & Options

Trusted Platform Module 7 - 41

6. Use the arrow keys to select the TPM State menu.

7. Select TPM State, and set the item to Enable and press Enter.

8. Press F10 to save the changed BIOS information, exit the BIOS and restart the

computer.

See Over.

Figure 7 - 27

TPM State

Modules & Options

7 - 42 Trusted Platform Module

9. If you make any changes to the TPM State you will be asked to Execute/Reject

the change after restart.

10. Press F10 to save the changes and exit.

11. Restart the computer.

12. You can now configure the TPM from the TPM Administration menu (see over).

Figure 7 - 28

Physical Presence

Operations

Modules & Options

Trusted Platform Module 7 - 43

TPM Driver Installation

1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

2. Click Option Drivers (button).

3. Click 6.Install TPM Driver > Yes.

4. Click Install.

5. Click Next.

6. Click the button to accept the license and click Next.

7. Add tour information and click Next > Next > Install.

8. Click Finish > Yes to restart the computer.

Modules & Options

7 - 44 Trusted Platform Module

Initializing TPM

Make sure you prepare a removable media (e.g. a USB flash drive) to store

passwords etc. before beginning the initialization process. Insert the drive into

one of the computer’s USB ports prior to initialization.

1. Click Start > Programs/All Programs > Infineon Security Platform Solution >

Manage Security Platform.

Figure 7 - 29

Infineon Security

Platform Settings

Tool (Not

Initialized)

Click on any

the initialization

tab to bring up

prompt.

Modules & Options

Trusted Platform Module 7 - 45

2. When the platform has not been initialized you can click on any tab to bring up the

dialog box that will prompt you to start initialization.

3. Click Yes to start initialization.

4. Select the initialization method you want to use (Quick initialization is

recommended for most users).

Figure 7 - 30

Initialization

Prompt



Initialization

Quick Initialization

intended for most users

to quickly initialize the

Security Platform and

User with default set-

tings.

Advanced Initial-

ization

is intended for

expert users to initialize

the Security Platform

and configure Security

Platform features.

(backup. Emergency

Recovery, Password

Reset, Enhanced Au-

thentication).

Figure 7 - 31

Initialization

Wizard

Modules & Options

7 - 46 Trusted Platform Module

5. Select either a removable media or hard disk partition (see sidebar) to store

important data and passwords etc.

6. Click Next to begin the initialization.

7. Select the Security Platform features you want to use (Encrypting File System

and/or Personal Secure Drive) and set (and confirm your password).

8. Click Next > Next > Finish.

9. You can then configure the options from any of the tabs in the control panel.



Using Hard Disk

Partitions

If you do not use a re-

movable media to store

important data and

passwords you can use

hard disk partitions. If

you ar not using a re-

movable media for stor-

age then additional

secret data will be gen-

erated to protect the da-

ta. Make sure that the

selected drive and se-

cret data are not en-

crypted.

Figure 7 - 32

Configure Security

Platform Settings

Modules & Options

Trusted Platform Module 7 - 47

Infineon Security Platform Settings Tool

The Infineon Security Platform Settings Tool allows you to manage and check the

TPM state, manage your password information, and to backup and restore the TPM

data. As TPM is usually administered within large enterprises and organizations,

your system administrator will need to assist you in managing the information here.



Help

Right-click the taskbar

icon to bring up the

menu to select Help or

How to use the Security

Platform Features.

Backup

It is recommended that

you create a backup of

your TPM information

from the Backup tab.

Figure 7 - 33

Infineon Security

Platform Settings

Tool

Modules & Options

7-48

Troubleshooting

Overview 8 - 1

Chapter 8: Troubleshooting

Overview

Should you have any problems with your computer, before consulting your service representative, you may want

to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This

can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these

pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.

If all else fails, talk to your service representative. You should also make a record of what happened and what

remedies you tried.

Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview

this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off

for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call

your service representative.

Troubleshooting

8 - 2 Basic Hints and Tips

Basic Hints and Tips

Many of the following may seem obvious but they are often the solution to a problem when your computer ap-

pears not to be working.

• Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip,

make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indica-

tors” on page 1 - 7) to see the computer’s power status.

• Connections - Check all the cables to make sure that there are no loose connections anywhere.

• Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys config-

ured in your Power Options (see “Power-Saving States” on page 3 - 6), the Fn + F4 key combination, or

power button to wake-up the system.

• Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the bright-

ness.

• Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display.

• Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive

(this is a common cause of the message “Invalid system disk - Replace the disk, and then press any key” /

“Remove disks or other media. Press any key to restart”).

Troubleshooting

Backup and General Maintenance 8 - 3

Backup and General Maintenance

•Always backup your important data, and keep copies of your OS and programs safe, but close to hand.

Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal-

let.

• Run maintenance programs on your hard disk and OS as often as you can. You may schedule these pro-

grams to run at times when you are not using your computer. You can use those that are provided free with

your OS, or buy the more powerful dedicated programs to do so.

• Write down your passwords and keep them safe (away from your computer). This is especially important if

you choose to use a Supervisor password for the BIOS (see

“Security Menu” on page 5 - 15).

• Keep copies of vital settings files such as network, dialup settings, mail settings etc.(even if just brief notes).



Warranty

The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your war-

ranty.

Troubleshooting

8 - 4 Viruses

Viruses

• Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses

to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm

your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini-

tions file updates are usually downloadable directly from the internet.

• Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within e-

mail attachments so take care when opening any attached file. You can configure most Anti-Virus pro-

grams to check all e-mail attachments. Note: You should also beware of files from people you know as the

virus may have infected an address book and been automatically forwarded without the person’s knowl-

edge.

• Keep a “Bootable CD-ROM/DVD-ROM/USB storage device” (this CD/DVD/USB device provides basic

information which allows you to startup your computer) handy. You may refer to your OS’s documentation

for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at

least instructions on how to make one).

Troubleshooting

Upgrading and Adding New Hardware/Software 8 - 5

Upgrading and Adding New Hardware/Software

• Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are

doing, otherwise you will risk severely damaging your system.

• Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what

you are doing.

• Read the documentation. We can assume, since you are reading this that you are looking at the computer’s

manual, but what about any new peripheral devices you have just purchased? Many problems are caused by

the installation of new hardware and/or software. Always refer to the documentation of any new hardware

and/or software, and pay particular attention to files entitled “READ ME” or “READ ME FIRST”.

• When installing a new device always make sure the device is powered on, and in many cases you will need

to restart the computer. Always check that all the cables are correctly connected.

• Make sure you have installed the drivers for any new hardware you have installed (latest driver files are

usually available to download from vendor’s websites).

Troubleshooting

8 - 6 Upgrading and Adding New Hardware/Software

• Thoroughly check any recent changes you made to your system as these changes may affect one or more

system components, or software programs. If possible, go back and undo the change you just made and see

if the problem still occurs.

• Don’t over complicate things. The less you have to deal with then the easier the source of the problem may

be found; Example - if your computer has many devices plugged into its ports, and a number of programs

running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and

restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and

removing devices and restarting where necessary) will often find the source of a problem, although this may

be time consuming.

Troubleshooting

Problems and Possible Solutions 8 - 7

Problems and Possible Solutions

Problem Possible Cause - Solution

You turned on the power but it doesn’t

work.

Battery missing / incorrectly installed. Check the battery bay, make sure the

battery is present and seated properly (the design of the battery only allows it to

go in one way). Make sure there’s nothing interfering with the battery contacts.

The battery LED power indicator , is

blinking orange.

Low Battery. Plug in the power source. If the computer doesn’t start up

immediately, turn it off then on again.

You are losing battery power too quickly. The system is using too much power. If your OS has a Power Options scheme

(see “Power Plans” on page 3 - 4) check its settings. You may also be using

an ExpressCard/USB device/external device that is drawing a lot of power.

Actual battery operating time is shorter

than expected.

The battery has not been fully discharged before being recharged. Make sure

the battery is fully discharged and recharge it completely before reusing (see

“Energy Star Power Saving” on page 3 - 10).

Power Options have been disabled. Go to the Control Panel in Windows and

re-enable the options.

A peripheral device/USB device/ExpressCard is consuming a lot of power. Turn

off/remove the unused device to save power.

Troubleshooting

8 - 8 Problems and Possible Solutions

The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not

blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn

it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see

“Overheating” on page 1 - 13). Make sure you’re using the correct adapter.

Make sure that your notebook is completely powered off before putting it into a

travel bag (or any such container). Putting a notebook which is powered on in a

travel bag may cause the Vent/Fan intakes to be blocked.

Nothing appears on screen. The system is in a power saving mode. Toggle the sleep/resume key

combination, Fn + F4 (see “Configuring the Power Buttons” on page 3 - 8).

The screen controls need to be adjusted. Toggle the screen control key

combinations Fn + F8/F9. If you’re connected to an external monitor, make sure

it’s plugged in and turned on. You should also check the monitor’s own

brightness and contrast controls.

The computer is set for a different display. Toggle the screen display key

combination, Fn + F7. If an external monitor is connected, turn it on.

The screen saver is activated. Press any key or touch the TouchPad.

No image appears on the external

monitor I have plugged in and powered

on.

You haven’t installed the video driver and configured it appropriately from the

Control Panel. See Appendix B for instructions on installing and configuring

the video driver.

Problem Possible Cause - Solution

Troubleshooting

Problems and Possible Solutions 8 - 9

You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS.

Contact your service representative for help.

The sound cannot be heard or the volume

is very low.

The volume might be set too low. Check the volume control in the Volume

Control Panel in the Windows taskbar, or use the key combination Fn + F5 and

F6 (see “Function/Hot Key Indicators” on page 1 - 10) to adjust.

The CD/DVD cannot be read. The CD/DVD is dirty. Clean it with a CD/DVD cleaner kit.

The CD/DVD tray will not open when

there is a disc in the tray.

The CD/DVD is not correctly placed in the tray. Gently try to remove the disc

using the eject hole (see “Loading Discs” on page 2 - 3).

The DVD regional codes can no longer

be changed.

The code has been changed the maximum 5 times. See “DVD Regional

Codes” on page 2 - 5.

Unwelcome numbers appear when

typing.

If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on

page 1 - 7).

Problem Possible Cause - Solution



Password Warning

If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot

remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

Troubleshooting

8 - 10 Problems and Possible Solutions

The system freezes or the screen goes

dark.

The system’s power saving features have timed-out. Use the AC/DC adapter,

press the sleep (Fn + F4) key combination, or press the power button if no LEDs

are lit.

The system never goes into a power

saving mode.

Power Options features are not enabled. Go to the Windows Power Options

menu and enable the features you prefer (see “Power-Saving States” on

page 3 - 6). Make sure you have enabled Hibernate mode from the control

panel.

The Wireless LAN/Bluetooth/3.75G

modules cannot be detected.

The modules are off. Check the LED indicator and/or function key indicator

to see if the WLAN/Bluetooth/3.75G/HSPA module is on or off (see “LED

Indicators” on page 1 - 7). If the LED indicator is off, then press the Fn + F11

(WLAN), Fn + F12 (Bluetooth) or Fn + (3.75G) key combination(s) in order

to enable the modules (see “Function/Hot Key Indicators” on page 1 - 10).

Problem Possible Cause - Solution



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will

detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not

work.

Troubleshooting

Problems and Possible Solutions 8 - 11

The Wireless LAN indicators

show that the WLAN module is powered

on, however the module does not connect.

The WLAN module is turned off in the Windows Mobility Center. The

computer’s wireless function keys will not function properly if Wireless is turned

OFF in the Windows Mobility Center control panel. Make sure that Wireless is

ON in the Mobility Center to ensure proper function key behavior (see

“Wireless Hot Keys” on page 3 - 12).

The PC Camera module cannot be

detected.

The module is off. Press the Fn + F10 key combination in order to enable the

module (see “Function/Hot Key Indicators” on page 1 - 10). Run the

BisonCap program to view the camera picture.

The Wireless LAN/Bluetooth/ PC

Camera/3.75G/HSPA modules cannot be

configured.

The driver(s) for the module(s) have not been installed. Make sure you have

installed the driver for the appropriate module (see the instructions for the

appropriate module in “Modules & Options” on page 7 - 1).

A file cannot be copied to/from a

connected Bluetooth device.

The transfer of data between the computer and a Bluetooth enabled device is

supported in one direction only (simultaneous data transfer is not

supported). If you are copying a file from your computer to a Bluetooth enabled

device, you will not be able to copy a file from the Bluetooth enabled device to

your computer until the file transfer process from the computer has been

completed

The Bluetooth module is off after

resuming from Sleep.

The Bluetooth module’s default state will be off after resuming from the Sleep

power-saving state. Use the key combination (Fn + F12) to power on the

Bluetooth module after the computer resumes from Sleep.

Problem Possible Cause - Solution

Troubleshooting

8 - 12 Problems and Possible Solutions

A yellow exclamation mark appears

alongside PCI Simple Communications

Controller (Other Devices) in Device

Manager.

The MEI driver will fix this known issue. Install the MEI driver (see “MEI Driver”

on page 7 - 34).

The system is experiencing problems with

an attached e-SATA (external Serial

Advanced Technology Attachment) device.

Follow the instructions to install the Matrix Driver from the location indicated

below:

1. Insert the Device Drivers & Utilities + User’s Manual disc and click

Browse CD/DVD.

2. The driver is located in the following location on the disc:

X:\Option\00_iMSM\iata_cd.exe.

3. Double-click the executable setup file and follow the on-screen instructions

to install the driver.

Problem Possible Cause - Solution

Troubleshooting

Bluetooth Connection Problems 8 - 13

Bluetooth Connection Problems

If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and

headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Win-

dows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center

Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.

1. Install the Microsoft Windows Device Center Driver as appropriate for your operating system.

Windows 7

requires further configuration.

3. Make sure the Bluetooth device is powered on.

4. Go the Windows 7 control panel and double-click Device Manager (Hardware and Sound > Devices and

Printers).

5. Bluetooth Peripheral Device(s) will be listed under Other Devices (note this will only be listed if you have

connected, or tried to connect to, a Bluetooth device previously).

Figure 8 - 1 - Device Manager



Bluetooth Peripheral Devices

You will need to repeat the procedure

listed here for all Bluetooth Peripher-

al Devices listed under Other Devices

i.e. until there are no more Bluetooth

Peripheral Devices listed under this

menu heading.

Troubleshooting

8 - 14 Bluetooth Connection Problems

6. Right-click Bluetooth Peripheral Device and click on Update Driver Software.

7. Click Browse my computer for driver software.

8. Click Let Me pick from a list of device drivers on my computer.

Figure 8 - 2 - Browse my computer.../Let me pick from...

9. Select Bluetooth Radios from the list.

Figure 8 - 3 - Select Bluetooth Radios

Troubleshooting

Bluetooth Connection Problems 8 - 15

10. A list of drivers will appear with Manufacturer on one side and Model in the other.

11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not

choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for

Microsoft Corporation to appear in the list).

12. Select Windows Mobile-based device support from the Model list.

Figure 8 - 4 - Select Device Driver

13. Click Next > Yes and the driver will install.

14. Click Close to complete the installation.

Make sure you select

Microsoft Corporation

Troubleshooting

8 - 16 Bluetooth Connection Problems

15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth

Radios.

16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.

Figure 8 - 5 - Device Manager - Bluetooth Radio

Interface (Ports & Jacks)

Interface (Ports & Jacks) A - 1

Appendix A: Interface (Ports & Jacks)

Overview

The following chapter will give a quick description of the interface (ports & jacks) which allow your computer

to communicate with external devices, connect to the internet etc.

Item Description

Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the

slot and it will appear as a removable device.

DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.

External Monitor (VGA)

Port

This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or

simultaneous display on the LCD and external monitor/FPD.

e-SATA Port Plug external Serial ATA hard drives into this e-SATA (external Serial Advanced Technology

Attachment) port (see page 8 - 12 if you are experiencing problems with an attached e-SATA

device).

e-SATA /

Interface (Ports & Jacks)

A - 2 Interface (Ports & Jacks)

HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) is an audio/video connector interface for

transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or

Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries

both audio and video signals.

Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to

a reduced level before connecting to this jack.

Microphone-In Jack Plug an external microphone in to this jack to record on your computer.

RJ-45 LAN Jack This port supports LAN (Network) functions.

Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.

Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be

purchased at any computer store.

S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD-

capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound.

Item Description

Interface (Ports & Jacks)

Interface (Ports & Jacks) A - 3

USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed

peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as

external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into

the computer, and unplugged from the computer, without the need to turn the system off (if the

power rating of your USB device is 500mA or above, make sure you use the power supply which

comes with the device).

Item Description

Interface (Ports & Jacks)

A - 4 Interface (Ports & Jacks)

Intel Video Driver Controls

Intel Video Driver Installation B - 1

Appendix B: Intel Video Driver Controls

The basic settings for configuring video are outlined in “Video Features” on page 1

- 17.

Intel Video Driver Installation

Make sure you install all the drivers in the order indicated in

Table 4 - 1, on page 4 - 3

Video

1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/

DVD drive.

1. Click 2.Install VGA Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

Dynamic Video Memory Technology

Intel

DVMT automatically and dynamically allocates as much (up to 1.7GB) sys-

tem memory (RAM) as needed to the video system (the video driver must be in-

stalled). DVMT returns whatever memory is no longer needed to the operating

system.



DVMT Notes

DVMT is not local video

memory.

DVMT is not user-con-

figurable.

DVMT will not function

in MS-DOS. DOS uses

the legacy memory indi-

cated.

Intel Video Driver Controls

B - 2 Intel® Graphics & Media Control Panel

Intel® Graphics & Media Control Panel

Advanced video configuration options are provided by the Intel® Graphics and

Media Control Panel. To access the control panel:

1. Click Advanced settings in the Screen Resolution control panel in Windows.

2. Click the Intel(R)... tab and click Graphics Properties (button).

3. Right-click the desktop and select Graphics Properties from the menu.

4. Double-click the Intel(R) G&M control panel in Windows.

Figure B - 1

Intel® G&M

Control Panel

Intel Video Driver Controls

Intel® Graphics & Media Control Panel B - 3

You may make changes to any of the graphics properties by clicking the appropriate

menu tab on the left of the menu and adjusting the settings on the right.



Options & Support

Click Options & Sup-

port and select an item

from the sub-menu to

bring up the help and

support topics.

You will need to be con-

nected to the Internet to

access the key resource

links.

Multiple Display

At least one other dis-

play must be attached in

order to view multiple

display selection op-

tions.

Figure B - 2

Intel® G&M

Control Panel Tabs

Intel Video Driver Controls

B - 4 Intel® Graphics & Media Control Panel

Display Devices & Options

Besides the built-in LCD you can also use an external monitor/flat panel display/TV

connected to the external monitor port or to the HDMI-Out port (High-Definition

Multimedia Interface) as your display device. The table below outlines the display

options.

Intel Display Mode Description

Single Display One of the connected displays is used as the display device

Clone Displays

Both connected displays output the same view and may be

configured independently

Extended Desktop

Both connected displays are treated as separate devices, and

act as a virtual desktop



Function Key

Combination

You can use the Fn + F7

key combination to tog-

gle through the display

options:

• Notebook Only

• External Display Only

• Notebook + External

Display

Make sure you give the

displays enough time to

refresh.

Note that HDMI sup-

ports video and audio

signals.

Table B - 1

Display Modes



Attaching Displays

When you first attach an external display you may find that the desktop does not occupy

the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R)

G&M control panel to configure the full screen display.

Intel Video Driver Controls

Attaching Other Displays B - 5

Attaching Other Displays

If you prefer to use a monitor or flat panel display, connect it to the external monitor

port or HDMI-Out port on the right of the computer.

To Clone Displays:

1. Attach your display to the external monitor port or HDMI-Out port, and turn it on.

2. Go to the Intel(R) G&M control panel and click Display > Multiple Displays.

3. Click Operating Mode and select Clone Displays from the menu.

4. Click Apply, and OK to confirm the settings change.

5. You can switch the Primary/Secondary Display from the menu.



Multiple Display

At least one other dis-

play must be attached in

order to view Multiple

Display selection op-

tions.

General Settings

Click General Settings

to access settings the

options for any attached

display.

Figure B - 3

Display > Multiple

Displays (Clone)

Intel Video Driver Controls

B - 6 Attaching Other Displays

To Enable Extended Desktop:

1. Attach your display to the external monitor port or HDMI-Out port, and turn it on.

2. Go to the Intel(R) G&M control panel and click Display > Multiple Displays.

3. Click Operating Mode and select Extended Desktop from the menu.

4. Click Apply, and OK to confirm the settings change.



Display Settings

Extended Desktop

You can have different

Colors, Screen Area

and Monitor Refresh

Rates for each display

device provided your

monitor can support

them.

You can drag the moni-

tor icons to match the

physical layout of your

displays. Icons and pro-

grams may also be

dragged between the

displays.

Figure B - 4

Display > Multiple

Displays (Extended)

Click the appropriate monitor

icon and drag it to match the

physical arrangement you

wish to use (e.g. the second-

ary display may be extended

left/right/above/below the

primary display).

Click General Settings to

make any adjustments re-

quired.

Intel Video Driver Controls

Configuring an External Display in Windows 7 B - 7

Configuring an External Display in Windows 7

You can also use the Screen Resolution control panel in Windows 7 to configure an

external display.

1. Attach your display to the external monitor port or HDMI-Out port, and turn it on.

2. Go to the Screen resolution control panel (see “Video Features - Win 7” on

page 1 - 16).

3. Click the Detect button.

4. The computer will then detect any attached displays.



Function Key

Combination

You can use the Fn +

F7 key combination to

toggle through the dis-

play options:

• Notebook Only

• External Display

Only

• Notebook + External

Display

Make sure you give the

displays enough time

to refresh.

Note that HDMI sup-

ports video and audio

signals.

Figure B - 5

Screen Resolution

Multiple Displays

(Win 7)

Intel Video Driver Controls

B - 8 Configuring an External Display in Windows 7

5. You can configure the displays from the Multiple Displays menu.

• Duplicate these displays - Shows an exact copy of the main display desktop on

the other display(s).

• Extend these displays - Treats both connected displays as separate devices.

• Show desktop only on 1/2 - Only one of your displays is used.

Figure B - 6

Screen Resolution

Multiple Display

Options

(Win 7)

Intel Video Driver Controls

Configuring an External Display in Windows 7 B - 9

Using the Windows Logo Key + P Key Combination to Switch Displays

You can also use the + P key combination to quickly change display configura-

tion and modes (this is particularly useful when attaching a projector) in Windows 7.

1. Attach your display to the external monitor port or HDMI-Out port, and turn it on.

2. Press the

+ P key combination.

3. An on-screen menu will pop up.

4. Use the cursor keys (or

+ P) to select the appropriate configuration from the

menu, and press Enter to confirm the selection.

Figure B - 7

+ P Display

Configuration

Selection

(Win 7)

Intel Video Driver Controls

B - 10 HDMI Audio Configuration

HDMI Audio Configuration

HDMI (High-Definition Multimedia Interface) carries both audio and video signals

and you will can configure the audio output as per the instructions below when an

HDMI enabled device is connected to the HDMI-Out port.

Windows Audio Setup for HDMI

1. Connect a device with HDMI support to the HDMI-Out port.

2. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

3. Click Sound (Hardware and Sound).

4. Click Playback (tab), and click to select HDMI Device.

5. Double-click HDMI Device (or right-click the icon and select Properties).

Figure B - 8

HDMI Device

Click the taskbar volume in-

dicator when HDMI De-

vice is selected, and you will

note that the icon at the top of

the volume level indicator

has changed.

Intel Video Driver Controls

HDMI Audio Configuration B - 11

6. Adjust the HDMI settings from the control panel tabs.

7. Click OK to close the Sound control panel.

Figure B - 9

HDMI Device

Properties

Intel Video Driver Controls

B - 12 HDMI Audio Configuration

HDMI Notes

• Connect a device with HDMI support to the HDMI-Out port BEFORE attempt-

ing to play audio/video sources through the device.

HDMI Video Configuration

1. Connect an HDMI cable from the HDMI-Out port to your external display.

2. Configure your external display as per the instructions in “Attaching Other

Displays” on page B - 5.

3. Set up your external display (TV or LCD) for HDMI input (see your display device

manual).

4. You can now play video/audio sources through your external display.



Other Applications

If you are using a third

party application to

play DVDs etc. from

any attached DVD de-

vice, you will need to

consult the applica-

tion’s documentation

to see the appropriate

audio configuration

(the application must

support digital to ana-

log translation).

Specifications

Specifications C - 1

Appendix C: Specifications



Latest Specification Information

The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/

speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check

with your service center for details.

Specifications

C - 2 Specifications

Processors For All Models

Intel® Core™ i7 Mobile Processor:

i7-620M (2.66GHz)

32nm (32 Nanometer) Process

Technology, 4MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

===============================

Intel® Core™ i5 Mobile Processor:

i5-540M (2.53GHz)

32nm (32 Nanometer) Process

Technology, 3MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

i5-520M (2.40GHz)

32nm (32 Nanometer) Process

Technology, 3MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

Processor For Model B Only

Intel® Core™ i5 Mobile Processor:

i5-430M (2.26GHz)

32nm (32 Nanometer) Process

Technology, 3MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

===============================

Intel® Core™ i3 Mobile Processor:

i3-350M (2.26GHz)

32nm (32 Nanometer) Process

Technology, 3MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

i3-330M (2.13GHz)

32nm (32 Nanometer) Process

Technology, 3MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

===============================

Intel® Celeron® P4500 Processor:

(1.86GHz)

32nm (32 Nanometer) Process

Technology, 2MB L3 Cache & 1066MHz

FSB -

TDP 35W

rPGA988A Socket P Package

Core Logic

Model A:

Intel® QM57 Chipset

Model B:

Intel® HM55 Chipset

Display

15.6” (39.62 cm) HD (1366 * 768) / HD+

(1600 * 900) 16:9 TFT LCD

Memory

Dual Channel DDRIII (DDR3)

Two 204 Pin SO-DIMM Sockets

Supporting

DDRIII (DDR3)

1066MHz/

1333MHz (operational frequency is

dependent on processor FSB)

Memory Expandable up to 8GB

(2GB / 4GB

DDRIII (DDR3)

Modules)

Specifications

Specifications C - 3

Video Adapter

Intel GMA HD

Enhanced Video and 3D Engine

DVMT Memory Architecture up to 1.7GB

Supports Microsoft DirectX

® 10.0

Hardware Acceleration Decoded for

Blu-ray

BIOS

One 32Mb SPI Flash ROM

Phoenix™ BIOS

Storage

One Changeable 12.7mm(h) Optical

Device (CD/DVD) Type Drive (Super

Multi / Blu-ray Combo)

Easy Changeable 2.5" 9.5 mm (h) SATA

(Serial) HDD

Audio

High Definition Audio Interface

Stereo Enhanced Sound System

Built-In Microphone

Two Built-In Speakers

Keyboard & Pointing Device

Isolated Full Size WinKey Keyboard with

Independent Numeric Keys

Built-in TouchPad (integrated scrolling

key functionality) with Multi Gesture

Function

Three Instant Keys (WWW, E-Mail, Silent

Mode)

Interface

Three USB 2.0 Ports (one power share

USB)

One eSATA Port

One HDMI Out Port

One External Monitor Port

One Headphone-Out Jack

One Microphone-In Jack

One S/PDIF-Out Jack

One RJ-11 Jack

One RJ-45 LAN Jack

One DC-In Jack

*One Docking Port (cold plug)

*Docking Port is a Factory Option for

Model A Computers and is supplied as

standard for Model B Computers.

Card Reader

Embedded 9-in-1 Card Reader

(Supporting Push-Push Function)

- MMC/ RS MMC

- SD/ Mini SD / SDHC/ SDXC Compatible

- MS/ MS Pro/ MS Duo

Note: Some of these cards require PC

adapters that are usually supplied with

the cards.

Slots

One ExpressCard/34/54 Slot

Two Mini-Card Slots (USB/PCIe):

Slot 1 for WLAN Module with HMC Slot

and PCIe Interface

Slot 2 for 3.75G Mini-Card Slot with USB

Interface (

Factory Option

)

Specifications

C - 4 Specifications

Communication

Built-In 56K FAX Modem V.90 & V.92

Compliant

10/100/1000 MB Base-TX Ethernet LAN

Bluetooth v2.1 + EDR (Enhanced Data

Rate) Module

(

Factory

Option

)

2.0M Pixel USB PC Camera Module

Intel

WiFi Link 6200

(802.11 a/g/n) Half

Mini-Card PCIe WLAN Module

(Factory Option)

Intel

WiFi Link 6300

(802.11 a/g/n) Half

Mini-Card PCIe WLAN Module

UMTS/HSPDA-based 3.75G Module with

USB Mini-Card Interface (

Factory Option

)

Quad-band GSM/GPRS (850 MHz, 900

MHz, 1800 MHz, 1900 MHz)

UMTS WCDMA FDD (2100 MHz)

Note that UMTS modes CAN NOT be

used in North America.

=======================================

3rd Party 802.11b/g/n Half Mini-Card

Wireless Lan Module with PCIe Interface

(

Factory

Option for Model B Only

)

Power Management

Supports Wake on LAN

Supports Wake on USB

Supports Resume From Modem Ring

Power

Full Range AC/DC Adapter

AC input 100 - 240V, 50 - 60Hz

DC Output 19V, 3.42A (65 Watts) or

18.5V, 3.5A (65 Watts)

6 Cell Smart Lithium-Ion Battery Pack,

48.84WH

*9 Cell Smart Lithium-Ion Battery Pack,

77.76WH

(

Factory Option

)

*Note that the system cannot be

connected to the docking station if the 9

cell battery is inserted in the battery

compartment.

Security

Security (Kensington® Type) Lock Slot

BIOS Password

Fingerprint Reader Module

with Trusted

Platform Module Support

For Model A Only:

Intel vPro Support

Operating System

Windows® 7

Environmental Spec

Temperature

Operating: 5

°C - 35°C

Non-Operating: -20°C - 60°C

Relative Humidity

Operating: 20% - 80%

Non-Operating: 10% - 90%

Dimensions & Weight

374mm (w) * 256mm (d) * 37.9mm (h)

2.5 kg With 6 Cell Battery & ODD

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata M-book 6000 in the language / languages: English as an attachment in your email.

The manual is 4,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Maxdata M-book 6000 Manual

Product: