664283
9
Zoom out
Zoom in
Previous page
1/12
Next page
9
PROPER USAGE
MOUNTING THE STEPPER
1. Stand behind the unit.
2. While holding both of the rear
arm handles, place one foot on
the corresponding footpad. Wait
until the footpad comes to a stop
at the bottom of the stroke.
3. Then place your other foot
on the opposite pedal.
4. Your unit offers a variety of foot
positions. Moving your foot to the
forward most position of the foot pad
increases your step height, which will
create a feel similar to a step machine.
Placing your foot toward the back of the
foot pad decreases your step height and
creates more of a gliding feel, similar to
a smooth walk or run. Always make sure
your entire foot is secured on the foot
pad. The pedal motion is dependent.
5. To determine proper workout position,
stand on the pedal with your foot on
the center of the pedal. Keep your
knees slightly bent at all times.
BEFORE YOU BEGIN
LOCATION OF THE UNIT
Place the unit on a level and stable surface away from direct
sunlight. The intense UV light can cause discoloration on the
plastics. Locate your unit in an area with cool temperatures
and low humidity. Please leave a clear zone behind the
unit that is at least 24” (600 mm). This zone must be clear
of any obstruction and provide the user a clear exit path
from the machine. Do not place the unit in any area that
will block any vent or air openings. The unit should not be
located in a garage, covered patio, near water or outdoors.
LEVELING THE EQUIPMENT
Locate a level, stable surface to position the Stepper. The
Stepper has leveling feet located under the foot support.
If your Stepper wobbles in the location where you intended to use it, loosen
the lock nut on the adjusting foot and adjust the feet until stable. Once
level, lock the adjusting feet by tightening the lock nut to the frame.
WARNING!
Our equipment is heavy, use care and additional help if necessary when
moving. Failure to follow these instructions could result in injury.
POWER
If your unit is powered by a power supply, the power must be plugged
into the power jack, which is located in the front of the machine near the
stabilizer tube. Some units have a power switch, located next to the power
jack. Make sure it is in the on position. Unplug cord when not in use.
WARNING!
Never operate equipment if it has a damaged cord or plug, if it is
not working properly, if it has been damaged, or immersed in water.
Contact Customer Tech Support for examination and repair.
FREE AREA
0.6 m (2 ft)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Matrix S7xe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Matrix S7xe in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Matrix S7xe

Matrix S7xe User Manual - English - 64 pages

Matrix S7xe User Manual - English - 12 pages

Matrix S7xe User Manual - German, Dutch, French, Italian, Polish, Portuguese, Spanish - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info