738346

Matrix Performance Cycle Upright Manual

12
Zoom out
Zoom in
Previous page
1/135
Next page
12
BEFORE YOU BEGIN
LOCATION OF THE UNIT
Place the equipment on a level and stable surface away from direct sunlight.
The intense UV light can cause discoloration on the plastics. Locate your
equipment in an area with cool temperatures and low humidity. Please
leave a clear zone on both sides of the equipment that is at least 24”
(600 mm). This zone must be clear of any obstruction and provide the
user a clear exit path from the machine. Do not place the equipment in
any area that will block any vent or air openings. The equipment should
not be located in a garage, covered patio, near water or outdoors.
LEVELING THE EQUIPMENT
The equipment should be level for optimum use. Once you have
placed the equipment where you intend to use it, raise or lower one
or both of the adjustable levelers located on the bottom of the frame.
Use 6mm hex key through the access hole (shown below).
A carpenter’s level is recommended.
NOTE: There are only two levelers on the equipment.
WARNING!
Our equipment is heavy, use care and additional help if necessary when
moving. Failure to follow these instructions could result in injury.
POWER
If the equipment is powered by a power supply, the power must be plugged
into the power jack, which is located in the front of the equipment near the
stabilizer tube. Some equipment has a power switch, located next to the power
jack. Make sure it is in the ON position. Unplug cord when not in use.
WARNING!
Never operate equipment if it has a damaged cord or plug, if it is not working properly, if it has
been damaged, or immersed in water. Contact Customer Tech Support for examination and repair.
HYBRID SEAT HEIGHT
To adjust the seat height on the Hybrid Cycle, pull the orange lever under the seat and
lower the seat to the lowest position. Stand on either side of the seat, grab the orange
lever, lift the seat until the seat base is level with your hip bone, release lever and allow
seat to lock into place.
RECUMBENT SEAT HEIGHT
To adjust the seat height on the Recumbent Cycle, locate the orange lever under the seat
before you mount the Cycle. Place your right hand on the orange adjustment handle
under the seat. Place feet on the ground while seated and slide forward if needed. Place
feet on pedals, gently lift lever under the seat. Using legs, slowly push and slide the seat
up or down to desired position. Release lever and allow seat to lock into place.
UPRIGHT SEAT HEIGHT
To raise the seat height on the Upright Cycle, pull the seat upward. To lower the seat,
locate the orange adjustment lever under the seat and pull the lever up to slide the seat
down. Release lever and allow seat to lock into place.
The seat height adjusts from level 1 to 23. Do not raise the seat past level 23.
BRAKE SYSTEM
This equipment utilizes magnetic resistance to set specific levels
of resistance. The resistance level setting in addition to the
RPM is used to determine the power (watts) output.
FREE AREA
0.6 m
(2 ft)
0.6 m
(2 ft)
0.6 m
(2 ft)
ENGLISH
TRAINING AREA
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Matrix Performance Cycle Upright at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Matrix Performance Cycle Upright in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 46,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Matrix Performance Cycle Upright

Matrix Performance Cycle Upright User Manual - English - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info