738354
14
Zoom out
Zoom in
Previous page
1/20
Next page
13
CHAPTER 6: Preventative maintenance
b. Check brake pad setting by first turning the resistance knob toward the
“-“ sign as far as it will go (minimum braking effect). The brake pad should
have approximately a credit card thickness between it and the flywheel and
the brake pad should feel slightly loose around its pivot. If adjustment is
required see TROUBLESHOOTING GUIDE (see page 13).
c. Check brake pad for signs of wear and the presence of lubrication. If the
brake pad requires lubrication, first adjust the resistance knob so the brake
pad is just slightly touching the flywheel. Then slowly rotate the flywheel
with one hand while applying a small amount of lubricant on the flywheel
just behind the brake pad (A) on the in-going side. Wipe off excess.
d. Replace brake pad if necessary
e. Replace lower inside plastic cover
2. Check and tighten (if necessary) the screws on crank arms, adjustment
knobs and levers, seat, water bottle holder, and plastic covers.
6.4 BI-YEARLY (6 MONTH) MAINTENANCE
1. For optimal performance of the drive system the following steps should
be taken:
a. Remove the RIGHT crank arm by removing 5 socket head cap screws
with a 4mm ALLEN KEY WRENCH then remove the upper outside plastic
cover by removing 5 socket head cap screws with a 3mm ALLEN KEY
WRENCH. Then remove both of the lower plastic covers by removing 9
socket head cap screws with a 3mm ALLEN KEY WRENCH and 5mm
ALLEN KEY WRENCH.
b. Thoroughly wipe down around all internal components and look for signs
of excessive wear or damage.
c. Lubricate both upper and lower drive chains. Clean excess.
d. Replace drive chains if necessary
e. Replace all plastic covers and RIGHT crank arm
6.5 TROUBLESHOOTING GUIDE
Follow the steps below if any problems are discovered in the weekly
function test.
CRANK ARMS NOT SYNCHRONIZED
Turn the resistance knob toward the “+” sign until the crank arms do not
fall by themselves back to the lowest rest position. Raise the crank arms
so the crank handles are nearly level. Loosen (do not remove) the 5 socket
head cap screws (B) on the RIGHT crank arm with a 4mm ALLEN KEY
WRENCH. Adjust the position of screws within the slots until both crank
handles are level and then tighten. Make sure all screws are tight, or the
crank handle may slip out of synchronization again.
Rotation Direction
A
B
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Matrix Krankcycle at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Matrix Krankcycle in the language / languages: English as an attachment in your email.

The manual is 3,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info