Manual Mastervolt DC Master 24 12-3A (page 2 of 4) (English, German, Dutch, French, Italian, Spanish)

785612

Zoom out

Zoom in

1/4

ENGLISH

 Be sure that the output of the supplying source is switched off during installation. Also be sure that no consumers are

connected to the batteries during installation, to prevent hazardous situations.

 Check that the battery voltage is the same as the converter’s input voltage (e.g. 24V battery for a 24V input voltage).

Also check that the output voltage satisfies loading requirements

 Integrate a fuse in the positive wiring, nearby the battery.

See figures. 1. Select a cool, dry and ventilated position. 2. Use the bracket to mark the position of the holes. 3. Drill

3.5mm holes. 4. Fix the clip using screws provided. 5. Click the unit onto the clip.

6. Connect both input wires first. Only then connect the output wires.

NEDERLANDS

 Overtuig u zelf ervan dat de uitgang van de voedingsbron spanningsloos is gedurende de installatiewerkzaamheden.

Zorg er tevens voor dat er geen gebruikers zijn aangesloten op de accugroepen ter voorkoming van onveilige situaties

 Controleer of de accuspanning overeenkomt met de ingangsspanning van de converter (bijv. een 24V accu bij een

ingangsspanning van 24V). Controleer tevens of de uitgangsspanning geschikt is voor de aan te sluiten belasting

 Neem in de plusleiding een zekering op in de bedrading en plaats deze zo dicht mogelijk bij de accu.

Zie de afbeeldingen. 1. Kies een koele, droge en geventileerde montageplaats. 2. Gebruik de beugel om de boorgaten te

markeren. 3. Boor 3,5 mm gaten. 4. Zet de beugel vast met de meegeleverde schroeven.

5. Klik het voorwerp vast in de clip. 6. Sluit beide ingangsdraden het eerst aan, daarna pas de uitgang.

DEUTSCH

 Stellen Sie sicher, dass der Ausgang der Versorgungsquelle während der Installation ausgeschaltet ist. Es ist

ebenfalls wichtig, dass während der Installation keine Verbraucher an den Batteriesätzen angeschlossen sind, um

gefährliche Situationen zu vermeiden.

 Stellen Sie vor dem Anschließen sicher, dass die Spannung der Batterie der Sicherungsspannung des Gleichrichters

entspricht (z. B. eine 24 V Batterie für eine 24 V Sicherungsspannung). Prüfen Sie ebenfalls, dass die

Ausgangsspannung den Ladeanforderungen gerecht wird.

 Schließen Sie eine Sicherung in der Nähe der Batterie an das Pluskabel an.

Sehen Sie die Abbildungen. 1. Wählen Sie einen trockenen, gut belüfteten Montageplatz. 2 Markieren Sie die 3 Löcher

des Montageclips. 3 Bohren Sie Löcher mit einem 3,5mm Bohrer. 4 Montageclip mit den mitgelieferten Schrauben

befestigen. 5 Spannungswandler in den montierten Clip einsetzen. 6 Zuerst die Eingangs-, danach die

Ausgangsleitungen anschließen.

FRANÇAIS

 S’assurer que la sortie de la source d’alimentation est arrêtée pendant l’installation. Vérifier également qu’aucun

appareil n’est connecté aux batteries pendant l’installation, afin d’éviter toute situation dangereuse.

 Vérifier que la tension batterie est la même que la tension d’entrée du convertisseur (par exemple batterie 24V pour

une tension d’entrée 24V). Vérifier également que la tension de sortie satisfait aux exigences de charge.

 Insérer un fusible dans le câblage positif et le placer à proximité de la batterie.

Voir les illustrations 1. Choisissez un emplacement frais, sec et ventilé. 2. Utilisez le support pour positionner les trous. 3.

Percez des trous de 3,5mm. 4. Fixez le T à l’aide des vis fournies. 5. Cliquéz le convertisseur dans son T de fixation. 6.

Connectez en premier les fils d’entrée et ensuite les fils de sortie.

CASTELLANO

 Para prevenir situaciones de peligro, asegúrese que la salida de la fuente de alimentación esté desconectada y de

que ningún consumo permanezca conectado a las baterías, durante la instalación.

 Antes de conectar, compruebe que el voltaje de la batería es el mismo que el del voltaje de entrada del transformador

(p.ej. una batería de 24V para un voltaje de entrada de 24V). Compruebe también que el voltaje de salida satisface

los requisitos de la carga.

 Integre un fusible en el cableado positivo y colóquelo cerca de la batería.

Ver las ilustraciones 1. Elija un lugar frío, seco y ventilado. 2. Utilice el soporte para marcar la posición de los agujeros. 3.

Taladre agujeros de 3,5 mm. 4. Ajuste el soporte con los tornillos que se suministran.

5. Coloque la unidad sobre el soporte. 6. Primero conecte los dos cables de entrada. Después de salida.

ITALIANO

 Verificare che durante l’installazione, l’uscita della fonte di energia sia spenta. Inoltre verificare che gli utilizzatori

collegati alla batteria siano spenti, per prevenire pericoli.

 Prima del collegamento, controllate che la tensione della batteria coincida con la tensione di ingresso del convertitore

(ad esempio, una batteria da 24V per una tensione di ingresso di 24V). Verificate anche che la tensione di uscita sia

conforme ai requisiti di carico.

 Integrare un fusibile nel cablaggio positivo e collocarlo vicino alla batteria.

Vedi le illustrazioni. 1. Per il montaggio scegliere un luogo asciutto e ben aerato. 2. Segnare i tre fori della clip di

montaggio. 3. Perforare i fori con un trapano di montaggio da 3,5mm. 4. Fissare le clip di montaggio con le viti in

dotazione. 5. Posizionare il trasformatore di misura voltometrico nella clip cosi montata. 6. Collegare prima il cavo di

entrata poi quello di uscita.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mastervolt DC Master 24 12-3A in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0.79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mastervolt DC Master 24 12-3A Manual

Product: