785622
5
Zoom out
Zoom in
Previous page
1/16
Next page
ENGLISH
5
Installation
Be sure that the output of the supplying source is switched off during installation. Also be sure that
no consumers are connected to the batteries during installation, to prevent hazardous situations.
Install the Charge Mate Pro not only as close as possible to the supplying source, but to the
batteries as well. The Charge Mate Pro must be installed in a well-ventilated environment, as high
currents will heat up the Charge Mate Pro. Preferably, the Charge Mate Pro should be mounted on
a flat metal surface, with the fins vertical.
Check the installation drawing for correct connection.
Use the template from the packaging to determine the exact location and screw holes for mounting
of the device.
Install the Charge Mate Pro in the positive lead between the battery banks.
Connect the negative of the battery banks to the Charge Mate Pro
Optionally you can install a remote status light to the Status output and A+.
Do not install the Charge Mate Pro directly above the batteries because of possible
corrosive sulphur fumes.
Remote switch (optional)
Optionally you can install a single pole ON-OFF-ON switch for remote operation of the Charge Mate
Pro, see installation drawing on page 2.
Remote switch functions
ON
Switches input to 12/24 V.
The battery banks are connected in parallel and bi-directional without current limit.
PULSE
Switches input to 12/24 V for a short time.
Emergency start (battery banks are connected for 30 seconds without current limit)
OFF
Switches input to Ground. The Charge Mate Pro is switched off.
AUTOMATIC
Let the Switch input floating (or no switch connected).
Default automatic mode with 40A / 90A fixed current limit.
LED indicators
The green status led is continuous lit when there is an electrical connection between A+ and B+.
The red warning led is lit when there is no electrical connection between A+ and B+.
Warning LED
1 blink
Overvoltage
The voltage on A+ and/or B+ has been above 15,5/31 V for more than 1 s. The warning
disappears when voltage drops below 15/30 V for more than 10 s.
2 blinks
High voltage differential
A voltage differential between A+ and B+ has been detected of more than 8/16 V for more than 2,5
s. The warning disappears when the voltage differential drops below 8/16 V for more than 2,5 s.
3 blinks
Temperature too high (75 °C / 167 °F)
This warning disappears when the temperature drops below 65 °C/ 149 °F.
4 blinks
Reverse current
Reverse current detected from B+ to A+ for more than 2s. Disappears after 20 s.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mastervolt Charge Mate Pro 90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mastervolt Charge Mate Pro 90 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info