788781

Master Lock LTW123GTC Manual

3
Zoom out
Zoom in
Previous page
1/8
Next page
3
ENGLISH
2 A Slide out the battery drawer
on the side of the keypad.
B Insert 4 AAA alkaline
batteries (not included)
Note: Do not use rechargeable
batteries or any other type of
non-alkaline battery. Do not mix
old and new batteries. Do not mix
alkaline and standard batteries.
C Slide battery drawer back
into keypad.
3
M100TEST
SN100TEST01*
12345
Find your 5 digit factory code on
the back of this owner’s manual.
WARNING: Test your code several times before putting
valuables inside.
Unlocking your safe
1 FOR DUAL KEY/COMBINATION
LOCKS ONLY, insert key into the
lock, turn to the ’unlocked’
position, then remove the key
This is a secondary locking
feature not an override key.
2 A Enter the 5 digit factory code
found on the back of the
owner’s manual.
Note: You may have to lift
the handle while entering
the combination.
B A green light will indicate the
code is correct. You will have
4 seconds to turn the handle
to unlock your safe.
3 Rotate the handle downward to
open the door.
This may take a limited
amount of force if you have a
water-resistant safe.
NOTE: • Make sure the handle is rotated all the way up in the
horizontal position before unlocking the safe.
• If you exert too much force on the handle, the handle will
move without moving the bolts. If this happens, you will
hear a ’click.’ DO NOT be alarmed. This feature is designed
to protect the bolts from being over powered by force. If this
occurs, simply exert force in the opposite direction (lifting up)
until the handles ’clicks’ back into place and repeat steps 1-3
to open your safe.
• Delay mode will occur if three consecutive invalid entries have
been tried. Red LED will blink on and off to let you know the
safe is in delay mode. This will cause the system to shutdown
for two minutes. DO NOT remove the batteries to restart the
system it will only increase the length of time for the system
shutdown.
Locking your safe
1 Close the door and pull the
handle upward until the handle is
horizontal.
For water-resistant units,
additional pressure to the front,
left side of the door may need
to be applied prior to rotating
the handle.
2 FOR DUAL KEY/ELECTRONIC
LOCKS ONLY, insert key into the
lock, turn to the ’locked’ position,
then remove the key.
NOTE: If your safe does not
appear to be working properly,
please check to make sure you
are using NEW alkaline batteries
before contacting Master Lock
Customer Service.
Programming information
Three code options:
Factory code:
The safe will ALWAYS unlock using
this 5 digit code (found on the back of
the owner’s manual). This code cannot
be deleted.
User code:
A 5 digit programmable code of your
choosing that can be changed or
deleted or changed.
Secondary code:
A second 5 digit programmable code of
your choosing that can be changed or
deleted. Can only be programmed after
a user code has been activated.
NOTE: • The “C” key is a clear key. This can be used at anytime to
clear the system and return to standby mode – unless you are
in delay mode (3 consecutive invalid entries).
• The 5 digit factory code cannot be deleted. However, you may
add and delete additional codes.
This safe can store up to three codes at one time. One factory
code and two additional programmable codes.
Programming the user code
To ADD a user code:
1 Press the “P” key.
2 Enter the 5 digit factory code found on the back of your owner’s
manual.
3 The light will flash green and then you will have five seconds to
enter your own personal 5 digit user code.
To DELETE a user code:
1 Press the “P” key.
2 Enter the 5 digit factory code.
3 Enter 0,0,0,0,0.
NOTE: • The electronic lock will NOT indicate that it has deleted the
user code – please test the code to make sure it has been
deleted.
• Test with door open when programming.
Programming the secondary code
To ADD a secondary code:
1 Press the “P” key two times.
2 Enter the 5 digit user code previously programmed.
3 The light will flash green and then you will have five seconds to
enter your own personal 5 digit secondary code.
To DELETE a secondary code:
1 Press the “P” key two times.
2 Enter the 5 digit user code.
3 Enter 0,0,0,0,0.
NOTE: • The electronic lock will NOT indicate that it has deleted the
secondary code – please test the code to make sure it has
been deleted.
How to operate the light
The safe you have purchased may include a light. This is a long-lasting
LED light. Not all safes include a light.
The batteries that operate the keypad
are the same batteries that operate the
light. If the light in your unit does not
turn on, please change your batteries.
The light will turn on every time you
enter your code and will remain on
for 30 seconds. The light duration has
three options – off, 30 seconds, and 60 seconds.
To turn the light off:
1 Press the “0” button.
2 Press the “P” button.
3 Press the “3” button.
To turn the light on for 30 seconds:
1 Press the “0” button.
2 Press the “P” button.
3 Press the “4” button.
To turn the light on for 60 seconds:
1 Press the “0” button.
2 Press the “P” button.
3 Press the “5” button.
NOTE: • If the light duration is 60 seconds, the battery life will be
reduced at a faster rate.
Operating sound features
For Programmable Electronic Lock Only
The tones of the key pad may be turned on and off depending on user
preference.
Turn sound off:
1 Press “O”.
2 Press “P” key.
3 Press “2”.
Turn sound on:
1 Press “O”.
2 Press “P” key.
3 Press “1”.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Master Lock LTW123GTC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Master Lock LTW123GTC in the language / languages: English, Dutch as an attachment in your email.

The manual is 3.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info