588459
26
Zoom out
Zoom in
Previous page
1/64
Next page
4. The unit will shut down automatically after the SLEEP
function running for 12 hours.
5. Please note, the sleep function is not available while the
machine is working in ventilation. Only available in
Cooling or Heating mode.
6. When the machine is in Sleep function, the ventilation
would turn to be LOW.
Heating function (This is optional, only for cool & heat
model.)
1. When using Heat Pump, the ambient warm air is recycled
and use to heat the area where it is required. The Exhaust
Pipe must be fitted firmly to allow the cold air to be
removed outside.
2.
3. Continuous drain is compulsory while the unit is in heat
mode. Working range for heating function is 5 to 27oC.
For temperature outside this range, the unit may not work
properly.
TiO2 / Ionizer function (option)
1. This is only for the model with TiO2 or Ionizer function,
i.e. model no. with T or I. T stands for TiO2 (ultra-violet)
, I stands for Ionizer.
2. To start the TiO2 or Ionizer button, please press
TiO2/Ionizer button. These two functions can clean the air,
improve the air quality.
Regulating air flow direction
Adjust the air louvers by hand to control the air flow direction.
(Fig. 23)
Self-diagnosis
This machine is equipped with self-diagnosis function. If
something is wrong in the machine, the display window will show
the word “E1” or “E2”. As this time, please call your service
centre.
All the above functions can also be performed with the supplied
remote control. (Fig. 24)
This remote control requires one button cell (No.CR2025) to
operate
NOTICE !
1. To prolong the compressor's life, after switch-off of the
unit, please wait for 3 minutes (at least) before re-switch.
2. The cooling system will switch off if the ambient
temperature is lower than the set one. The ventilation,
however, keeps working on the set level. If the ambient
temperature rises above the selected level, the cooling will
return to work.
3. On the contrary, the heating will switch off if the ambient
temperature is higher than the set one (still, the ventilation
keeps working on the set level). As the ambient
temperature drops below the selected level, the heating
will return to work.
4. This machine is equipped with ANTI-FROST function.
While using the heating function during low temperature,
sometimes the heating will stop for a while in order to melt
the frost. As this occurs, just wait for the heating returns
to work.
DRAINAGE
During the process of cooling, some water will be extracted from
the air into the unit. If the tank is full, both of the compressor and
motor will stop. The “water full” sign will light on, also the
machine will beep as reminder.
To make the cooling work again, please empty the water by one of
the following ways:
Fig. 25
1. Turn off the air conditioner and avoid moving it when full.
2. Position a container (a water tray for example) underneath
the drain hole.
3. Remove the drain knob & rubber plug from the drain hole
and allow the water to drain out.
4. When the container is almost full, replace the rubber plug
in the drain hole and empty the water tray.
5. Repeat until the unit is emptied.
6. Replace the rubber plug and tighten the drain knob firmly.
7. Switch on the unit - the full water or compressor operating
indicator should not be flashing.
If you wish to operate the unit without the need to empty the water
tank, please:
Fig 26.
Remove the drain knob and rubber plug and retain for
future use.
Connect the drain tube supplied to the water outlet as
shown and locate the other end into a drain.
Fig. 27.
The drain tube may be extended by adding an extension
tube and using a suitable connector.
Please note (Fig. 28.)
1. The drain must be at or below the outlet level.
2. Flashing comp / ‘full water’ indicator will not function in
this mode of drainage.
3. If you want to extend the water tube, you can connect it
with another tube (OD: 18mm)
Special caution for heating function !(fig. 29)
While using the heating function, please note:
1. Install the exhaust pipe well, in order to exhaust the cool
air to outdoor. (Please refer to the instruction manual for
installation method.)
2. Fix the drainage to be continuous one (i.e. drain the water
by water tube).
3. Working range for heating function is 7 to 27oC (for
cooling function, it is 18 to 32oC). For temperature outside
this range, the unit may not work properly.
MAINTENANCE
Always unplug the air conditioner from the mains before
cleaning. To maximize the efficiency of the air conditioner
clean regularly.
Cleaning the housing
Use a soft, damp cloth to wipe the body clean.
Never use aggressive chemicals, gasoline, detergents, chemically
treated cloths, or other cleansing solutions. These all could
possibly hurt the cabinet.
Cleaning the filter
Use a vacuum cleaner or tap the filter lightly to remove loose dust
and dirt from the filters and then rinse thoroughly under running
water (no hotter than 40oC).
Dry thoroughly before replacing.
Notice! Never operate the unit without the filters.
End of season storage (fig. 30)
Drain any water in the unit before completely operating the
unit on ventilation only mode for a few hours, to
thoroughly dry the inside.
Clean or change the filter
Unplug and store the power cord as shown
Cover the cord storage
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for master AC 1400 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of master AC 1400 E in the language / languages: English, German, Danish, Italian, Polish as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info