442807
4
Zoom out
Zoom in
Previous page
1/5
Next page
17. TREBLE Control
By adjusting the Treble control you can add or take
away the higher frequencies in your bass tone. By
increasing the amount of treble you will make your
tone brighter, ideal for more percussive playing
styles.
BLEND
(Only on MB450H, MB4210 & MB4410)
You can select a blend of the two channels either
from the front panel or via the supplied footswitch.
18. BLEND Switch & LED
This switch turns the channel mixing on.
19. BLEND Control
By adjusting this control it is possible to blend your
signal between the Modern and Classic channels.
When you do this the LED will be illuminated red.
20. VOLUME Control - Blend
Adjusts the volume of the Blend.
21. VOLUME - Master
(Only on MB450H, MB4210 & MB4410)
Controls the overall volume.
22. CD IN Jack Socket
If you want to jam to your favourite CD, tape or
mp3 player, merely connect the headphone output
of your device here, adjust the player’s volume to
match that of your guitar and ‘hey-presto’- you've
got the perfect ‘play-along’practice system.
23. HEADPHONES Jack Socket
For use when silent practice is the order of the day.
Connection of headphones will automatically shut
down the internal speaker / speaker cabinet.
24. POWER Switch
The power switch turns your amplifier on and off.
The LED next to the ‘Modern / Classic’switch will
light up when your amplifier is turned on and will
not be lit when the amplifier is switched off.
Note: The power amplifier is protected by a
clipping limiter, so even when you play your amp
loud, the sound remains clean.
(panel shown is MB450H)
Rear Panel Features
1 2 3 4 5 6 7
EUROPE ONLY - Note: This equipment has been tested and found to comply with the requirements
of the EMC Directive (Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.
EUROPE ONLY - Note: The Peak Inrush current for the MB450H, MB4210 and MB4410 is 28 amps.
The Peak Inrush current for the MB150 is 30 amps.
The Peak Inrush current for the MB60 is 13 amps.
ENGLISH
ENGLISH
MB450H MB4210 MB4410 MB150 MB60
Power (RMS) @ 4 Ohms 300W 300W 300W 150W 60W
Power (RMS) @ 2 Ohms 450W 450W
*
450W
*
--
Pre-amp Valve ECC83 ECC83 ECC83 ECC83 ECC83
Bass Guitar Input Impedance 1MΩ 1MΩ 1MΩ 1MΩ 1MΩ
CD Input Impedance 10kΩ 10kΩ 10kΩ 10kΩ 10k
Emulated Output Level +4dBu +4dBu +4dBu +4dBu +4dBu
Weight 15kg 33kg 51kg 30kg 23kg
Size (mm) W, H, D 630 x 220 x 235 630 x 535 x 280 630 x 720 x 410 580 x 585 x 355 580 x 505 x 325
*
with extension cabinet
1. MAINS INPUT
Your amp is provided with a detachable mains
(power) lead, which is connected here.
Note: The specific mains input voltage rating that
your amplifier has been built for is shown on the
back panel. Before connecting for the first time,
please ensure that your amplifier is compatible with
your electricity supply. If you have any doubt,
please get advice from a qualified technician.
Your Marshall dealer will help you in this respect.
Please ensure the amplifier is switched off and
unplugged from the mains electricity supply before
being moved.
2. SPEAKER OUT Socket(s)
There is one speaker jack socket on the MB60 and
MB150 (marked ‘INTERNAL4Ω’). This is where the
power amplifier is connected to the internal
loudspeaker. It can be used to drive an external
cabinet of at least 4 Ohms impedance.
There are 2 speaker jack/SPEAKON
®
combo
sockets on the MB450H, MB4210 and MB4410.
They accept either a standard 1/4" jack or a
SPEAKON
®
connector and both of them carry the
same signal allowing 2 cabinets to be connected
simultaneously. The minimum load is 2 Ohms.
3. FOOTSWITCH Jack Socket
Connect the supplied footswitch here. This enables
you to change between Modern and Classic
channels. The MB450H, MB4210 & MB4410 have
a twin footswitch which also switches the Blend
feature.
4. PRE/POST Switch
Selects the signal available at the Balanced line
out. When in PRE position the buffered and level
adjusted input signal is present at the DI output.
The signal before the Master potentiometer is
made available at this connector when in POST
position.
5. BALANCED LINE OUT
The Line Out Jack can be used for connection to
recording equipment for direct recording or for
connection to a P.A. system.
6. RETURN Jack Socket
This is where you connect the OUTPUT of the
effects processor you are using in the effects loop.
7. SEND Jack Socket
If you want to use an external effects processor in
your amp’s built-in Series FX effects loop, this is
the jack you connect to the INPUT of the unit you
are using.
54
Technical Specification
Safe operating levels: The MB450, MB4210 and MB4410 amplifiers are designed to deliver 450W safely into 2ohm loads.
However, impedances lower than 4 ohms together with high signal levels will produce more internal heating which may
trigger the thermal protective muting.
Follow all instructions and heed all warnings
KEEP THESE INSTRUCTIONS !
MB60_150_450 hbk aw 1/3/07 12:05 pm Page 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall MB60, 150, 450H, 4410, 4210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall MB60, 150, 450H, 4410, 4210 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info