705282

Marshall DSL40CR Manual

3
Zoom out
Zoom in
Previous page
1/38
Next page
ENGLISH
PLEASE READ THIS MANUAL CAREFULLY
BEFORE PLUGGING IN.
FOLLOW ALL INSTRUCTIONS AND HEED ALL WARNINGS.
KEEP THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operaon is subject to the
following two condions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operaon.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or television
recepon, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modicaons not expressly approved by the party
responsible for compliance could void the users authority to operate the equipment.
This device complies with CAN ICES-3(B)/NMB-3(B)
COMPLIANCE STATEMENT
WARNING! IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
WARNING:
Before going any further, make sure that
your amplier is compable with your
mains electricity supply. If you have any
doubt, please seek help from a qualied
technician – your Marshall dealer can
help you in this respect.
MAINS INPUT & FUSE:
The specic mains input voltage
rang that your amplier has been
manufactured for is indicated on the
rear panel of the amplier. Your amplier
is provided with a detachable mains
(power) lead, which should be connected
to the MAINS INPUT socket on the rear
panel of the amplier (Rear Panel Funcon
#26). The correct value and type of
mains fuse is specied on the rear panel
of the amplier.
NEVER aempt to bypass the fuse or t
one of the incorrect value or type.
TRANSPORTING YOUR EQUIPMENT:
Please ensure that your amplier is
switched o, unplugged from the mains
electricity supply and all removable
cables have been disconnected from
your equipment before aempng to
move it.
IMPORTANT SET UP INFORMATION:
1. When using the DSL40CR, or the
DSL100HR with an extension
speaker cabinet(s), make sure
that the speaker cabinet(s) is
connected to the correct impedance
loudspeaker jack socket(s) on the
rear panel of the amplier. See
the LOUDSPEAKERS guide in this
manual for specic informaon
regarding impedance matching (Rear
Panel Funcon #33).
WARNING:
Failure to do the above may damage
your amplier. When connecng a
speaker cabinet make sure that you use
a proper speaker cable. Never use a
screened (shielded) guitar cable for this
purpose.
2. Ensure that the POWER switch is
set to the OFF posion (Front Panel
Funcon #25).
3. Ensure the OUTPUT switch is in
the STANDBY posion (Front Panel
Funcon #24).
4. Connect the supplied mains (power)
lead into the MAINS INPUT (Rear
Panel Funcon #26) rst and then into
an electricity outlet.
5. Ensure that the volume controls on
the front panel are set to zero (Front
Panel Funcons #19 & #21).
6. Plug your guitar into the INPUT jack
socket (Front Panel Funcon #1).
7. Switch the amplier ON using
the POWER switch, wait for a
few minutes and then switch the
OUTPUT switch to either the LOW
or HIGH posion.
8. Turn the selected channel volume
up to your preferred level and your
amplier is ready to play.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall DSL40CR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall DSL40CR in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 8,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info