168925

Marquant mcr 727 Manual

7
Zoom out
Zoom in
Previous page
1/8
Next page
MCR-727
RDS
AUX
SD
MIC
MP3
INPUT
INT21 RDM43
PWRRDS
65
BND
MOD
PAU
TA
PTY
S
I
P
D
LOCATION OF CONTROLS
3. PRE-SCAN/AUTO-STORE BUTTON / REPEAT CONTROL
a) On radio mode, this button allows you to enjoy “Preset Memory Scan” function by pushing it shortly, and “Auto-Store
Memory” function by pushing it more than 2 seconds.
lPS (PRESET MEMORY SCAN) - It calls the memorized station frequencies (from 1-6) automatically every 5 seconds.
lAS (AUTO-STORE MEMORY) - It searches all station frequencies upward and memorize automatically 6 stations by
catching the frequency which has scan-stop level, the memorized station is shown on LCD as “Channel 1 to 6”. After
memorizing, auto-store memory function will be changed to “Preset Memory Scan” function automatically.
b) Press this button to repeat the song during playback.
REM
ARK
:
AT ANY
TIME
, IF T
HE W
IRE HAS B
EEN DISC
ONNECTE
D, THE RESET
BUTT
ON MUST BE N
EED
TO RE
SET
AGAIN BE
FORE
OPERATE THE RADIO (
REFER TO RESET BUTTON
FOR
DETAI
LS).
OTHERWIS
E, THE RADIO M
AY NOT
WORK PROPER
LY.
OPERATING INSTRUCTIONS
1. POWER ON/OFF CONTROL
Press the button to turn the power “ON” or “OFF”.
Note : The unit can be turn on by pressing any keys on the panel (except panel release button & disc eject button). It will
help the user who cannot find the power button in dark.
5. LCD DIGITAL DISPLAY
The unit utilizes a digital type display which shows numerical indication of station FREQUENCY and other FUNCTIONS.
6. DISPLAY BUTTON
This button serves to show available information as following:
Station Name / Band & Frequency / Clock / Programme Type Name / Track No. & Playing Time
2. BAND SELECTOR / PAUSE CONTROL
a) On radio mode, each time this button is pressed, the radio band is changed. The indication “FM1”, “FM2”, “FM3”, “MW1” or
“MW2” will appear on the display according to your selection.
b) Press this button to pause during playback.
SETTING CLOCK TIME MANUALLY
1. Press “DISP” button to show “XX’XX” and hold it until the display flash and release.
2. Rotate “VOL/SEL” button clockwise to set HOUR and anti-clockwise to set MINUTE.
7. SCAN CONTROL
Press this button to scan the receivable FM / MW stations during radio mode. When receivable stations are tuned in, they are
monitored for approximately 5 seconds before advancing to the next receivable station. Press this button once again to stop
scanning as desired.
9. PANEL RELEASE BUTTON
This button is used to release the panel from the unit.
lTo detach the front panel, press the button so that the left side of the panel is released. Grasp the released side and pull
it off of the chassis (FIGURE A : TO REMOVE).
lTo re-attach the panel, insert the right side of the panel in place first and then press the left side of the panel until the
chassis hold the panel firmly (FIGURE B : FOR INSTALLING).
GB-2
10. MODE SELECTION / MUTE CONTROL
a) Briefly press this button to select Radio (TUNER), CD/MP3 (S-CDP), USB (USB-DRIV), SD (MEM-CARD), Auxiliary Input
(AUX) or A2DP (BT-PLAY) mode.
b) When pressing the button for more than 2 seconds, it will mute volume control and “MUTE ON” will appear on the display.
11. RDS (RADIO DATA SYSTEM) CONTROL
You can enjoy RDS advantages on FM radio as following.
l Program Service Name (PS) : When an RDS station is received, station's name will appear on the display.
l Traffic Program (TP) : When station with traffic program is received, “TP” indicator will appear on the display.
l Alternative Frequencies (AF) : The unit continuously checking the signal strength of alternative frequencies for the tuned
radio station. Every time that new alternative frequency is stronger than current station, it automatically switch over to the
new frequency and new frequency will be displayed for 1-2 second. When the button pressed short, AF switching mode
is selected and the state of AF switching mode will appear on the display as following.
-RDS indicator on : AF mode is on and RDS signal is received.
-RDS indicator off : AF mode is off.
-RDS indicator flashing : AF switching mode is selected but RDS signal is not received yet.
l Enhanced Other Networks (EON): An RDS service where the broadcaster links some stations together. When tuned to a
station which is linked to others by EON, the radio is capable of receiving Traffic Announcement from the linked stations.
l Regional Program (for some countries only) : When tuned to a regional program, the radio will stay tuned to that
particular regional program as long as possible. If you drive out of the coverage area and the regional program becomes
very weak, the radio may tune to another regional program from the same network. To activate the regional program
function, pressing the button more than 2 seconds until “REG ON” appear on the display. To switch off the regional
program function, pressing the button more than 2 seconds until “REG OFF” appear on the display.
14. VOLUME/SELECTION BUTTON (“VOL/SEL”)
Rotate the button anti-clockwise to decrease, or clockwise to increase volume level.
AUDIO LEVEL CONTROL (WHEN PUSHING ONE AFTER ANOTHER)
Press this button shortly one after another to show VOL/BAS/TRE/BAL/FAD control.
lVOLUME - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase volume level.
lBASS - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase bass level.
lTREBLE - Press this button once, then rotate anti-clockwise to decrease, or clockwise to increase treble level.
lBALANCE - Press this button once, then rotate anti-clockwise or clockwise to level balance of speaker right and left.
lFADER - Press this button once, then rotate anti-clockwise or clockwise to level fader of speaker front and rear.
AUDIO/SETTING SELECT (HOLD MORE THAN 2 SECONDS)
When pressing the button for more than 2 seconds, it activates as unit setting selection in cyclical mode as following. The
unit setting can be changed by rotating the button clockwise or anti-clockwise.
lTA SEEK / TA ALARM
lMASK DPI / MASK ALL
lRETUNE-S / RETUNE-L
lDSP OFF / POP M / ROCK M / CLASS M / FLAT M
lLOUD OFF / LOUD ON
lMULT OFF / MULT ON (not available for this model)
lSCROLL 1 / SCROLL 2 (display showing from left to right/right to left direction)
lBEEP ON / BEEP OFF (not available for this model)
lSTEREO / MONO
lDX / LOCAL
lPAIRING (for mobile phone pairing via Bluetooth)
15/16. MANUAL UP/DOWN TUNING / TRACK SEEK UP/DOWN CONTROL
On radio mode, pressing the button for more than 2 seconds, it will tune one frequency step higher or lower.
On CD/MP3/USB-DRIV/MEM-CARD mode, press this button will locate the beginning of the track being played or will locate the
beginning of the next track. When pressing more than 2 seconds, it will move fast forward or fast backward to a specific position.
17. STATION PRESET BUTTON (1-6)
The PRESET BUTTONS on the unit are used to store station frequencies which you may wish to recall. Each preset button can
store FM1, FM2, FM3, MW1, MW2 band station frequency. Pressing the button momentarily recalls the station frequency which
was memorized. There are 6 preset buttons, giving you capability of storing 18FM / 12MW.
NOTE: When the preset button to be memorized is kept pressed for more than 2 seconds, the receiving station frequency
will be stored in the button pressed. After this, the memorized station can be recalled by pressing the button once.
GB-3
4. DISC SLOT
Holding the disc and insert into the disc slot. The disc mechanism will automatically engage into CD/MP3 play mode.
8. EJECT BUTTON
Press the button to eject the disc inside disc slot.
(16) (17) (1) (20)(11)(13)(7)(6)
(21)(22)(5) (19)(8) (15)(2) (3)(10) (4)(12)(9)
(14)
(18)
RESET
MP3
INPUT
AUX SD
MIC
For TA Function
Briefly press the button to select TA mode on/off. When TA mode is on, “TA” indicator will appear on the display and the radio is
able to receive traffic announcements on the same stations or stations linked via EON with Traffic Program (TP). The TA mode
can work as following.
l If the volume setting is very low, volume level will be raised temporarily during traffic announcement and back to original volume
level at the end of traffic announcement.
l Temporary switch over to an EON linked program when EON detects a traffic announcement on that other program.
l If the radio is muted, it will be de-muted for the duration of the traffic announcement.
l If the unit is on CD/MP3/USB-DRIV/MEM-CARD mode, it will switch temporarily to radio mode to receive Traffic Announcement.
For PTY Function
There are 2 series of programme type (PTY) available for PTY search tuning when you press the button more than 2 seconds
and then pressing any Station Preset Button (1-6) until the desired PTY code appears on the display. The radio will stop on
station transmitting the selected PTY code. Next PTY searching can be activated by repeating the same procedure. During
programme type searching, PTY button can be pressed to stop searching and the radio will back to the original station. “PTY
NONE” will appear on the display if the selected PTY code is not receivable.
12. TA (TRAFFIC ANNOUNCEMENT) / PTY (PROGRAMME TYPE NAME) CONTROL
On CD / MP3 / USB-DRIV / MEM-CARD Mode
lPreset 2 - press this button to scan the first 10 seconds of all the tracks on the CD / MP3 / USB drive / SD Card.
lPreset 4 - press this button to play the tracks on the CD / MP3 / USB drive / SD Card in random order.
lPreset 5 - press this button to search -10 track (for MP3 / USB-DRIV / MEM-CARD Mode only).
lPreset 6 - press this button to search +10 track (for MP3 / USB-DRIV / MEM-CARD Mode only).
18. RESET BUTTON
The RESET button is located on the front of main panel. It is recessed in order to prevent accidental engagement,and can be
activated with the tip of a ball-point pen or any similar pointed object. This reset circuitry is provided in order to protect the
unit's microprocessor, and should only be activated under the following conditions :
a) Initial installation after all wiring is completed.
b) Abnormal operation is encountered such as numerical indication on display is erratic.
c) Whenever the reset button is activated, all preset memory content will be erased and must be reprogrammed.
FIGURE B: FOR
INSTALLING
FIGURE A: TO
REMOVE
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marquant mcr 727 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marquant mcr 727 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info