97347
8
Zoom out
Zoom in
Previous page
1/64
Next page
8 © MARMITEK
2. INSTALLATION
Connecting the cameras:
Secure the camera at any suitable wall that you desire (fig. 2, 3 and 4).
Connect the 4 pin DIN plug of signal & DC cord ‘D’ to the camera (fig.4).
Connect the yellow RCA jack of signal & DC cord ‘D’ to the A/V terminal ‘CH1’ of the SD recorder (fig.4).
Connecting the power adapters (see fig. 4):
Connect the DC plug of DC power cord splitter ‘E’ to ’DC IN’ connector of the SD recorder.
Connect the female DC connector (plug with hole connector) of signal & DC cord ‘D’ to one of the
two remaining male DC plugs (plug with pin connectors) of DC power cord splitter ‘E’.
Connect the female DC connector of DC power cord splitter ‘E’ to the DC adaptor.
Connecting to TV or monitor (see fig. 4):
Connect the yellow RCA jack of A/V cable for video output ‘F’ to the A/V terminal on the back of the
SD recorder and connect the other yellow plug to the video-in connector of your TV.
Connect the white RCA jack of signal & DC cord ‘D’ to the audio input of your TV.
Connecting to TV or monitor using a SCART adapter (option):
When your TV doesn’t have an RCA A/V input but it does have a SCART connector, then you can connect
the SD recorder using an optionally available SCART adapter (Art. no: 27023 Marmitek SCART adapter
Receiver). (Please see fig. 5 for connection).
Connection to alarm output:
The NO (normally open) outgoing signal can activate an external alarm (the Normally Open contact closes for
about 10 sec. in case of an alarm). See the specifications of your alarm system for the connections (see fig. 6D).
Upon that, in combination with the Marmitek X-10 components, you can use this connection to switch a
(outside) light for example. Requirements for a simple connection are
(see fig. 6A)
:
SM10 (converts the SD recorder signal into a X-10 signal and puts it on the mains)
Art nr. SM10: EU: 08943, UK: 09552
AM12 or LM12 (receives the X-10 signal and switches the lights on or off)
Art nr. AM12: G: 08915, U:08978, I:09052, F:08916, CH:09249
Art nr. LM12: G: 08910, U:08977, I:09051, F:08911, CH:09248
For more information on the X-10 protocol and the use of it, visit our website http://www.marmitek.com.
Use of the external ‘trigger’ contact:
Every alarm contact can be connected to this input, in the form of a potential-free NO (normally open)
or NC (normally closed) contact, e.g. magnetic door/window contacts, motion detectors, etc. Multiple
detectors can be connected to the trigger contact, to activate the SD recorder and to start a recording
(serial for NC, parallel for NO alarm contacts)
(see fig. 6C)
.
For example, to have the SD recorder start recording due to a signal from an external Marmitek motion
detector, you will need the following components
(see fig. 6B)
:
SM10 AM12 LM12
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SD Memory2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SD Memory2 in the language / languages: Dutch as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info