494266

Marmitek MT20 Manual

18
Zoom out
Zoom in
Previous page
1/112
Next page
© MARMITEK
18
FREQUENTLY ASKED QUESTIONS
What is the reason for modules to switch on/off spontaneously?
It is possible that a Marmitek X-10 System is installed at one of your neighbours using
the same House Code. To solve this problem try to change the House Code of your
system, or have FD10 Phase Coupler/Filter installed at your incoming mains.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same
House Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or
Marmitek X-10 Security Console installed in your house. These components will
translate the radio signals to the Marmitek X-10 signal on the power line. Using
several remotes and sensors, you only need one central transceiver.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of
your remotes is not sufficient. The TM13 is using so called collision detection to
prevent signals to be disturbed when more than one TM13 is transmitting. TM13’s
will wait for a quite power line before transmitting their data. To prevent your
Marmitek X-10 System to become slow or to prevent dimming from becoming less
smooth, make sure that the TM13 units are placed as far away from each other as
possible.
a Particular Module won’t go on or off from the buttons on the Mini Timer:
Check that you have power to the outlet controlling the Module and the switch on
the light or appliance is ON.
Check that the Unit Code and Housecode on the Module are set correctly. Try
plugging the Module and the Mini Timer into the same outlet. If the Module doesn’t
work in ANY outlet, not even with the Module and the Mini Timer in the same duplex
receptacle (top and bottom) the Module may be defective.
You can’t control ANY Modules from the Mini Timer.
Check that there is a time displayed on the Mini Timer and that you have power to
the outlet it is plugged into.
Check that the Housecode for the Mini Timer is set correctly (see Changing the
Housecode). Try plugging the Module and the Mini Timer into the same outlet. If
NONE of your Modules work in ANY outlet, not even with the Module and the Mini
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek MT20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek MT20 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info