494307

Marmitek LW11 Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
5. Remove the mounting plate by loosening both cross-head screws.
6. Fit the assembly plate on the back box with the countersunk screws.
7. Slide the plastic bezel over the wires.
8. Connect the wires: Phase to (L)
Neutral to (N)
Light wire to (L)
9. Connect the pulse switch(es), if applicable, to connectors
2 and L.
10. When connected, position light switch on the mounting
plate and reinsert both screws.
11. Finally, set the rotary code switches on the front side to
the desired address with a screwdriver.
12. Put the switch cover back on.
You are now able to control the switch both by hand and with a Marmitek X-10
Controller.
Switching system details
The status of the LW11G will change if the connected momentary switch is pressed for
less than 2 seconds. If the momentary switch is pressed longer, the LW11G will start to
dim. The module dims the lighting all the way down first and then all the way up.
ATTENTION: For safety reasons, when using the momentary switch, the phase wire to
which it is connected MUST originate from the same group.
FREQENTLY ASKED QUESTIONS
What is the reason for modules to switch on/off spontaneously?
It is possible that a Marmitek X-10 System is installed at one of your neighbours using
the same House Code. To solve this problem try to change the House Code of your sys-
tem, or have FD10 Phase Coupler/Filter installed at your incoming mains.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same
House Code (A .. P).
My LW11G has stopped reacting; the lights will not come on.
Check to see if the fuse is still in order. This is located behind the cover plate, and can
be opened with a screwdriver or a coin. Replace the fuse with one that is 2.5A (T) 5 x
20mm.
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or
Marmitek X-10 Security Console installed in your house. These components will trans-
6 © MARMITEK
20140_20061012_LW11G_UG_176 20-03-2007 08:41 Pagina 6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek LW11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek LW11 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info