494327
5
Zoom out
Zoom in
Previous page
1/8
Next page
Marmitek X-10
Infrared interface type IRIX35
26
Technical characteristics
Transposes 38 kHz InfraRed (IR) signals from the remote
control device into Marmitek X-10 commands on the power
line.
Axial sensitivity: 25 mtr. range (edge 45°, 7 m. range).
Possibility for standard and "toggle" IR receipt.
Possibility to control one user definable letter code
(16 addresses).
Designed as an wall- or ceiling mountable unit or for
stand-alone use.
The infrared protocol is compatible with the existing
X10 IR-protocol. This means that all standard X10 compatible
IR remote transmitters (controls) can be used.
Application options
The IRIX35 can be used to receive infra red-commands (IR) from
Marmitek X-10 remote controls and send them over the power
line to switch or dim Marmitek X-10 actuators (see figure 1).
Marmitek X-10 Infrared interface type IRIX35
27
Figure 1.
Marmitek Home Control Box
If the IRIX35 is used in combination with the Marmitek Home
Control Box. The IRIX35 can be used to activate the previously
programmed macros in the Marmitek Home Control Box, using a
remote control device.
Marmitek X-10 modules
IRIX35
Infrared
signals
Remote control
Marmitek
Home Control
Box
Lighting
circuit
signal
28
In principle, the IRIX35 can be used in two ways:
1. Fitted to a distribution box.
2. Connected to a wall socket.
Note: Switch off the power before starting the
assembly!
Fitting to a distribution box
To fit the IRIX35 to a distribution box, follow the steps below.
Remove the cover of the IRIX35 by loosening the screw at
the top.
Feed live and neutral through the rear plate by making an
opening through the sticker covering the mounting plate.
Firmly screw the mounting plate with screws to the
distribution box.
Connect live and neutral to the connector of the
mounting plate.
Firmly tighten the cover of the IRIX35 to the mounting
plate again.
!
Assembly
29
A
Fitting to a distribution box.
30
Connecting the power cord for use in a wall socket
If you wish to connect the IRIX35 to a wall socket, you must
connect the power cord provided.
To connect the power cord to the IRIX35, follow the steps
below.
Remove the cover of the IRIX35 by loosening the screw
at the top.
Use a Stanley knife to carefully cut open the recess on the
narrow side of the mounting plate so that the power cord
can be fed through.
Fit live and neutral to the connector and feed the cable
through the cable channel in the mounting plate.
Firmly tighten the cover of the IRIX35 to the mounting
plate again.
Assembly
(cont'd.)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek IRIX35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek IRIX35 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info