494263

Marmitek EasyTouch Panel10 X-10 Manual

11
Zoom out
Zoom in
Previous page
1/65
Next page
9Easy Touch Panel 10™
8. FREQUENTLY ASKED QUESTIONS
What is the reason for modules to switch on/off spontaneously?
It is possible that a Marmitek X-10 System is installed at one of your neighbours using the same House Code. To solve
this problem try to change the House Code of your system, or have FD10 Phase Coupler/Filter installed at your incoming
mains.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same House Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or Marmitek X-10 Security Console
installed in your house. These components will translate the radio signals to the Marmitek X-10 signal on the power line.
Using several remotes and sensors, you only need one central transceiver.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The
TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting.
TM13’s will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become
slow or to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as far away from
each other as possible.
I have defined a button but if I press this I hear a short beep but nothing happens.
The EasyTouch Panel 10 ensures that, after touching the screen, the corresponding Marmitek X-10 code is sent wirelessly.
This signal must be received by a Marmitek X-10 transceiver which then places this signal on the power line and can
then operate a module. Check whether your transceiver is receiving this by using a TM13 and defining, for example, a
TOGGLE button which is set to the house code of the TM13 and unit code 1. If you touch this button on the screen,
leaving a slight pause of 1 second between each touch, you should be able to hear the TM13 switch. If you have used
several house codes together, ensure that you also use several TM13 modules, each of which is set to a house code that
has been used. Or set the house code of your TM13 to house code P. Then, the TM13 will place ALL received house
codes on the power line.
I cannot find the selections ‘ALL LIGHTS ON’, ‘ALL LIGHTS OFF’, ‘ALL UNITS OFF’, ‘DIM UP’ and ‘DIM DOWN’.
These functions are not bound to a unit code. If you wish to programme these functions, browse through the unit codes
(1...16). You will find the above functions after unit code 16.
How can I move a button?
You move a button by deleting the existing button and adding it again.
How can I clean the screen?
You can use a clean, soft, lint-free cloth which you can moisten slightly with distilled water. Do not spray any fluids
directly onto the screen.
Do you still have questions? Please check out www.marmitek.com for more information.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek EasyTouch Panel10 X-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek EasyTouch Panel10 X-10 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info