494283

Marmitek DoorPhone 124 Manual

6
Zoom out
Zoom in
Previous page
1/100
Next page
6
© MARMITEK
3. INSTALLATION
Before you get started with the installation, it is necessary that you fully charge the handset
(4-5 hours).
Charge handset:
See figure 1
1. Remove the battery cover by pressing on the battery cover lock (23).
2. Insert the additionally supplied battery pack into the battery compartment. Make sure you
connect the right polarities of the battery and the handset (22).
3. Place the battery cover back onto the handset. Beware! Do not put on the handset yet.
4.
Insert the supplied power adapter into the connector at the back side of the docking station (28),
insert the electric plug into the power socket and place the handset into the docking station.
5. The red ‘Charge’ indicator light (25) and the green ‘Full’ battery indicator light (26) should
now go on and off alternately, which is to check the battery status. Shortly after that, only
the red charger indicator light (25) will keep flickering. During the charging, the battery
symbol
shall be visible in the LCD screen and the segments shall start moving to
indicate that the handset is being charged.
6. After approximately 4 till 5 hours, the battery should be fully charged and the ‘Full’ battery
indicator light (26) shall burn constantly. When the battery is fully charged, the battery
symbol
will disappear when the handset is off.
7. The handset is now ready for further installation. It is advisable that the handset be placed
in the docking station when not being used, so that it is always fully charged. This is not
damaging the battery.
Getting the set ready for installation:
The door unit needs to be set on the same channel as the handset. Check the settings and
adjust them if necessary, according to the instructions given below.
Note: - You always need to place 4 AA Penlite batteries into the door unit for start-up, even
when you will be using an external power supply (see ‘Pairing procedure’).
- In case you have more than one doorbell button on the door unit, then the channel
settings are predetermined at the factory and cannot be altered. In that case you can
skip the section ‘Channel settings door unit’.
A B C D
Figure 1
20194_20100216_UG_Doorphone120.i6 6 12-3-2010 9:52:19
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek DoorPhone 124 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek DoorPhone 124 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info