Manual Marklin 29310 - Forestry Starter Set (page 13 of 32) (English, German, Dutch, French)

640607

Zoom out

Zoom in

1/32

7.2 Changing an Address:

If you have 2 locomotives with the same address,

you can change the address for one locomotive

as follows:

Unplug the transformer. Set the address switches

to the desired address. Press the button „Change

Direction“ Hold this button pressed down while

the lens on the IR Control is pointed at shows to

the receiver, and plug the transformer back into

the wall outlet.

Release the button as soon the light comes on.

The programming procedure is displayed when

the light comes on or blinks. As soon as the light

goes out, the programming is turned off. The loco-

motive can now be run with the new address.

8. Locomotive Functions

•

Recognition of the mode of operation: automatic

• Addresses that can be set: 1 - 255

• Address set at the factory: 78

• Headlights for the locomotive. They can be

turned on and off in digital operation.

• ABV — Adjustable acceleration/braking delay.

• Adjustable maximum speed.

•

Setting the locomotive parameters (address, ac-

celeration/braking delay, maximum speed): with

the Control Unit, Mobile Station or Central Station.

8.1 Function Switch

The IR Controller can activate 5 digital functions

on the locomotives.

Controllable Functions:

Headlights

Warning light Function 1

ABV, off Function 4

8.2 Controlling the Locomotive

The control knob for operating locomotives

always controls only the locomotive that has just

been selected with the address selector switch.

All other locomotives or powered rail cars con-

tinue to run at the speed last set for them.

Important: When a new address is selected and

the control knob is already set at a speed position

(any speed position), the locomotive just selected

will immediately run at this speed. You must select

this locomotive address a second time, before you

can control the locomotive.

After you switch to a new address, it takes a

moment before the newly selected locomotive

can actually be controlled. This feature makes

it possible for you to skip over other addresses

when switching to a new address, without the

locomotives assigned to these addresses being

affected by the current setting for the control

knob. Control of the locomotive is assumed with

the last settings in use. The locomotive now

reacts to the controller.

9. Information about Operating the Train

Running 2 Trains

Only one switched mode power pack and one

Base Station may be used.

The switched mode power pack included with

the starter set provides power sufﬁcient for a

maximum of 2 trains.

The locomotive to be controlled can be selected

with the switch on the controller (see Sections 7

and 8).

10. Trouble Running the Train

• If the train does not run, check to make sure

that the connections have been done as shown

in Section 6.

• Check to make sure that the batteries in the

IR Controller have been installed correctly or

whether they are run down.

• Check to see if there a short circuit or an

overload on the layout or if a locomotive or

car is derailed. Correct the short circuit or the

overload by reducing the number of power

consumers (locomotives, lighted cars, etc.), and

set the derailed locomotive or car back on the

rails.

• If the locomotive is damaged, do not use it any

more. If a car becomes damaged, remove this

car from the train and do not use it anymore.

11. Cleaning and Maintenance

• Check to see if hair or dirt gets on the axles on

the train and remove this hair or dirt from the

axles with the help of a pair or tweezers so that

the train runs correctly.

• The train can be wiped with a dry, lint-free cloth.

• Additional maintenance information can be

found in Section 15.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Marklin 29310 - Forestry Starter Set in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marklin 29310 - Forestry Starter Set

Marklin 29310 - Forestry Starter Set Instructions - All languages - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Marklin 29310 - Forestry Starter Set Manual

Product: