522827

Marantz SR8002 Manual

20
Zoom out
Zoom in
Previous page
1/94
Next page
ENGLISH
17
BASIC OPERATION
USE MODE
(Normal operation status)
This remote controller is preset with a total of
12 types of remote codes, including Marantz TV
(television), DVD, VCR (VCR deck), DSS (satellite
broadcasting tuner), TUNER, CD/CD-R, MD, TAPE
(tape deck), AUX1, AUX2, and AMP (amplifi er).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1.
Press the SOURCE button.
For this example, press DVD.
DVD is shown on the LCD, and the remote controller
is set for DVD.
Pressing the
SOURCE
button once changes the
remote control to the settings for the source that
was pressed.
To change the amplifi er or other source, press the
SOURCE
button twice (double-click). The code is
sent, and then the amplifi er source changes to DVD.
2.
Press the buttons to operate the DVD.
The indicator is shown on the LCD while the
remote control codes are being transmitted. It is not
displayed when buttons without stored code are
pressed.
3.
The direct buttons can be used to perform up
to 20 operations for each of the 12 sources,
including DVD, TV, AMP, and other AV
equipment.
The buttons consist of the D1 to D5 buttons, and
the equipment is operated by pressing the buttons
corresponding to the indicators on the LCD.
Four pages are available, and press the
>
button
to select a page. The current page position is
displayed on the LCD.
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, VCR, LD, CABLE, DSS,
DVD, TAPE, TUNER, CD/CD-R, MD and AMP.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the
SOURCE button of the remote
controller.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote control
source name
Corresponding
preset code
Device name
TV TV Television
DVD DVD DVD player
VCR VCR Video deck
DSS SATELLITE Satellite broadcasting
tuner equipment
TUNER
RECEIVER/TUNER
AM FM TUNER
CD CD/CD-R PLAYER CD player
CD-R CD/CD-R PLAYER CD recorder
MD CD/CD-R PLAYER MD deck
TAPE TAPE Cassette deck
AUX1 CABLE Cable television
AUX2 LASER DISC Laser disc player
AMP AMPLIFIER Amplifi er or receiver
RECEIVER/TUNER
• When using Marantz products, TV and DVD can
be set to TV1 (TV/VDP: Projector) and TV2 (PDP:
Plasma display), and DVD1 (fi rst DVD player) and
DVD2 (second DVD player), respectively, to match
the customer’s operating environment. These
settings are made in PRESET mode.
In the factory default state, the remote controller is
set to TV1 and DVD1. To make the presets, enter
the numbers below while referring to the section
“Entering and Setting the Manufacturer Number
Directly”.
TV1: 0001, TV2: 0002
DVD1: 0001, DVD2: 0002
Entering and Setting the Manufacturer Number Di-
rectly
Refer to the manufacturer number list.
This example shows how to set a SAMSUNG DVD
player.
LEARN
NAME
MACRO
USE
PAG E
1 23
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
5 6
2 3 4
1.
View the supplied manufacturer number list,
and fi nd the number of the manufacturer for the
device that you are using.
2.
Hold down the M button for three seconds or
more.
The menu is displayed.
3.
Press the D1 (PRESET) direct button.
The Preset setting (P-SET) is displayed.
4.
Press the DVD source button.
5.
Press the numeric buttons to enter the four-
digit manufacturer number.
Example: To enter “0600” from the manufacturer
number list.
To correct the entered number, use the
1
or
2
cursor button to enter the correct number.
• If no button is pressed for over one minute
during the setting process, any settings that
were made are cancelled.
6.
Press the OK cursor button.
7.
Confirm the OK is displayed and then the
display returns to the Preset Setting (P-SET).
When the manufacturer number is entered correctly,
OK is displayed momentarily on the screen.
• If you enter a number not in the manufacturer
number list, WRONG CODE is displayed,
and then you return to the preset setting
again
Check the manufacturer number list, and
either set a different number or use the
sequence function to set.
8.
To set the manufacturer number for another
source device, repeat the procedure in steps 4
to 6.
9.
After the settings are completed, press the M
button.
10.
Press the buttons on the remote controller to
check that the DVD can be operated correctly.
Setting Equipment Not Appearing in Manufacturer
Number List
Use the sequence function to set equipment not
appearing in the manufacturer number list. You may
still be unable to set some equipment even when
using the sequence function. In this case, the remote
controller can be programmed with codes individually.
In the sequence function, the power ON/OFF codes
are transmitted by pressing the remote controller
buttons in order.
If the power for the equipment is left on, hold down
the button until the equipment is turned off, and then
release. This completes the setting.
This example shows how to set a DVD player.
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
4 5 7
1.
Turn on the power of the DVD player.
2.
Hold down the M button for three seconds or
more.
The menu is displayed.
3.
Press the D1 (PRESET) direct button.
The Preset setting (P-SET) is displayed.
4.
Press the DVD source button.
5.
Hold down the CH+ or CH– button for one
second or more.
6.
Press the CH+ button repeatedly in the interval
for one second.
The signal is transmitted, and the display cycles
through the code number.
Press the
CH–
button to go back to a number
screen.
7.
Release the button once the DVD player turns
off.
8.
Press the OK cursor button.
9.
Confirm the OK is displayed and then the
display returns to the Preset Setting (P-SET).
10.
To set the manufacturer number for another
source device, repeat the procedure in steps 4
to 8.
11.
After the settings are completed, press the M
button.
12.
Press the buttons on the remote controller to
check that the DVD can be operated correctly.
Check the following points if the equipment which
was set does not operate properly.
• If there is more than one number in the manufacturer
number list, try setting a different number.
• There may be some buttons which cannot be
used. Program the codes to the required buttons.
SR7002-8002_U_01_ENG 1_3.indd 17SR7002-8002_U_01_ENG 1_3.indd 17 07.8.24 1:14:48 PM07.8.24 1:14:48 PM
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR8002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR8002 in the language / languages: English as an attachment in your email.

The manual is 15,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info