62166

Marantz SR7002 Manual

49
Zoom out
Zoom in
Previous page
1/94
Next page
ENGLISH
46
Note:
• The detection check measures the state of use of all
speakers whether actually used or not.
For example, if the center speaker is not used, the
test tone will require time to go from the L-channel
to the R-channel, therefore be careful not to unplug
the microphone or operate this unit during this
time.
6.
When the 1 st Position Check ends, the
following OSD appears on the display.
AUTO SETUP
SPEAKERS CHECK:OK
2nd MIC POSITION!!
START
CHECK
CALCULATE
EXIT
Here, to view the results of the detection check,
select “CHECK” with the 3/4 cursor buttons
and press the OK/ENTER button. The results
will be displayed.
SPEAKER CONFIG
CHECK !! SPEAKER
FRONT : YES
CENTER : NON
FRONT R : YES
SURR.R : YES
SURR.B R : NON
SURR.B L : NON
SURR.L : YES
SUB W : YES
RETURN EXIT
If the check results indicate an error, take suitable
action with that item and remeasure. (For error
messages, see “ERROR MESSAGES” on
page 48.)
After confirming the check results, select
“RETURN” with the 3/4 cursor buttons and
press the OK/ENTER button to return to the
OSD menu.
At this point, you can select “EXIT” to end Auto
Setup and return to “2. SPKR SETUP”.
Note:
• AUTO SETUP is not available in Pure Direct,
Source Direct, or 7.1 Channel Input modes.
2-1 AUTO SETUP (MultEQ™ SETUP)
The AUTO SETUP (MultEQ™ Setup) feature of
the unit measures sound characteristics of the
speaker system and room where the unit is used and
automatically optimizes settings.
The Audyssey MultEQ™ technology adopted by
this unit provides the best listening environment for
multiple listeners.
To do this, the AUTO SETUP feature measures a
test tone emitted by each channel in a maximum of 6
listening positions, using the supplied microphone.
The measurement results are analyzed using an
original algorithm and environmental settings are
made to improve the sound characteristics of the
listening area.
To set up the speaker system (i.e., adjusting speaker
distance, etc.) without using the AUTO SETUP feature,
see “MANUAL SETUP” on page 49 of the manual.
HOW TO PERFORM AUTO SETUP
During measurement, the OSD menu displays the
condition, therefore turn power to the monitor on.
1.
Connect the supplied microphone to the MIC
jack on the unit.
AV SURROUND RECEIVER SR8002
POWER ON/OFF PHONES
STANDBY
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
DISP MULTI AUTO TUNED ST SPKR A B V-O FF
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1
PCM
AAC
AUX 1 INPUT
AUDIOS-VIDEODIGITAL VIDEO L R
DOWN
UP
VOLUME
ENTER
INPUT SELECTOR
M-DAX
M-DAX
2.
Set the microphone in the listening position.
Notes:
• Measurement can be done in a maximum of 6
listening positions.
For the fi rst measurement, set the microphone in the
main listening position.
• Use a stand or tripod to position the microphone at
ear height in the listening position.
• Remove any obstructions between the speakers and
microphone.
• To use the internal subwoofer of the amp, set the
volume to the middle point and set the crossover
frequency to the highest.
• During measurement, step away from the microphone
and operate the unit via the remote controller from a
position that is out of the path of the speaker sound.
• The test tone output from the speakers during
measurement is loud. Be mindful of neighbors and
watch out for small children.
3.
Select “2. SPKR SETUP” from the MAIN
MENU, select “AUTO SETUP” with the 3/4
cursor buttons, and press the OK/ENTER
button to display the start screen.
4.
Select the number of channels for the surround
back speaker you are using.
For a 5.1 channel speaker system, select
“NON” (Surround Back speaker off). (To use
speaker C or multi speaker, select “NON”. See
page 38, 55.)
Select “START” with the 3/4 cursor buttons
and press the OK/ENTER button to start
measurement.
AUTO SETUP
AUTO SETUP: START
MAIN ROOM
SURR BACK: 2CH
RETURN EXIT
5.
1 st Position Check
During the fi rst position check, the following
screen is displayed as the unit checks
background noise in the listening room,
presence of speakers, and speaker polarity
and measures the acoustical characteristics in
the fi rst position where the microphone is set
up.
AUTO SETUP
SPEAKERS CHECK:--
1st MIC POSITION
NOW ANALYZING !!
CANCEL
EXIT
7.
Move the microphone to the second listening
position, select “START” with the 3/4 cursor
buttons and press the OK/ENTER button to
measure the second point. At this point, you
can cancel second point measurement and
calculate measurement results by selecting
“CALCULATE” and pressing the OK/ENTER
button.
AUTO SETUP
SPEAKERS CHECK:OK
2nd MIC POSITION!!
START
CHECK
CALCULATE
EXIT
8.
Repeat steps 7 until measuring 6 points
between the main listening position and
surrounding positions.
When all measurements end, the following
OSD appears on the display.
AUTO SETUP
SPEAKERS CHECK:OK
CALCULATE
EXIT
Select “CALCULATE” with the 3/4 cursor
buttons and press the OK/ENTER button
to calculate measurement results. During
calculations, the following OSD appears on the
display.
AUTO SETUP
______________
NOW CALCULATING!
EXIT
Note:
• Less than 6 positions can be measured, but it is
recommended to measure in all 6 positions in order
to obtain the best results.
• The time needed to complete calculations depends
on the number of connected speakers and measured
listening positions. The more speakers and listening
positions, the more time is needed.
SR7002-8002_U_01_ENG 2_3.indd 46SR7002-8002_U_01_ENG 2_3.indd 46 07.8.24 1:15:23 PM07.8.24 1:15:23 PM
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR7002 in the language / languages: English as an attachment in your email.

The manual is 15,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR7002

Marantz SR7002 User Manual - Dutch - 74 pages

Marantz SR7002 User Manual - French - 84 pages

Marantz SR7002 User Manual - Spanish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info