62166
33
Zoom out
Zoom in
Previous page
1/94
Next page
ENGLISH
30
CLONE MODE
Creating copies using clone mode
All of the codes programmed to the RC101 remote
controller can be copied to another RC101 using a
few simple operations.
The remote controller can copy the entire
contents.
When copying the entire contents, all programmed
codes are copied.
Note:
The clone function can only be used for copying
when using the same model (RC101) for both the
transmitting and receiving remote controller.
Copying entire contents
1. Place the receiver sensor of the receiving
remote controller (top) so that it is facing the
transmitter of the transmitting remote controller
(top) at a distance of about 2 inches (5 cm).
2 inches
S
Y
S
T
E
M
R
E
M
O
TE
C
O
N
T
R
O
L
L
E
R
S
YS
T
E
M
R
E
M
O
T
E
C
O
N
T
R
O
L
L
E
R
2. Press SET button and PLAY button of the
transmitting remote controller until the SEND
indicator blinks twice.
Then backlight ashes
The transmitting side is now ready.
3. Press SET button and STOP button of the
receiving remote controller until the LEARN
indicator blinks twice.
Then backlight ashes.
The receiving side is now ready.
4. Press the ENTER cursor button on the receiving
remote controller.
Then back lights tune off.
5. Press the ENTER cursor button on the
transmitting remote controller.
Then backlights tune off.
6. When copying is started, the SEND indicator of
transmitting remote controller and the LEARN
indicator of receiving remote controller start to
blink.
When the copying operation is completed, the
back lights of transmitting remote controller and
receiving remote controller are turned on.
Do not touch either of the remote controls
during the copying operation. Doing so could
cause copying to fail.
If the copying fails in the middle of the copying
process, back light of receiving remote are
flash. Press the SET button to return the
normal mode. Check and perform steps 1 to 5
again.
Copying takes about 30 seconds to complete
when the transmitting remote controller has
been programmed to 100% capacity.
7. Once copying is completed, press the SET
button on both remote controls.
OTHER OPERATIONS
CHANGE THE MULTI ROOM CONTROL COMMANDS
FOR EACH ZONE
(When operating the unit by Multi Zone connected)
Zone A: MULTI ROOM A Control (Default)
Zone B: MULTI ROOM B Control
(The SR7002 does not use this zone.)
Zone C: The unit does not use this zone.
Zone D: MAIN ROOM
Change the control commands for each zone.
2.
1.
1. Press SET button and ZONE button until the
SEND indicator blinks twice.
Then backlight ashes.
2. Press each zone button(A/B button)
When the procedure is successful, the SEND
indicator will blink twice.
These buttons change a special code of each zone.
POWER ON/OFF
SOURCE
INFO
VOL +/–
SLEEP
MUTE
Tuner mode operation remote code (Refer to p.26)
CHANGE THE CONTROL COMMANDS OF MULTI
SPEAKER FUNCTION FROM MULTI ROOM.
1.
2.
1.
3.
1. Press SET button and POWER ON button until
the SEND indicator blinks twice.
Then backlight fl ashes.
2. Press the 1-digit code by numeric keys.
Multi room mode: 1 (Default)
Multi speaker mode: 2
Note
In case of Zone D, only control for main room is
possible.
3. Press ENTER button once to lock in the code.
When the procedure is successful, the SEND
indicator will blink twice.
These buttons change a special code of multi room
mode or multi speaker mode.
Note
The control commands can be set independently in
ZONE A/B.
POWER ON/OFF
VOL +/–
MUTE
SR7002-8002_U_01_ENG 1_3.indd 30SR7002-8002_U_01_ENG 1_3.indd 30 07.8.24 1:14:58 PM07.8.24 1:14:58 PM
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR7002 in the language / languages: English as an attachment in your email.

The manual is 15,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR7002

Marantz SR7002 User Manual - Dutch - 74 pages

Marantz SR7002 User Manual - French - 84 pages

Marantz SR7002 User Manual - Spanish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info