453909
96
Zoom out
Zoom in
Previous page
1/104
Next page
92
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
Resetting the microprocessor
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
Various setting details can be saved and reset on this device. If setting details are saved before returning
to the default values, after returning to the default settings, setting details can be returned to the same
values as before returning to the defaults.
AUTO AUTOBAND
ON/STANDBY ENTER
SURR. MODE
1
When the power is ON, press and hold BAND and ENTER for more than 3 seconds.
After “MEMORY SAVING” is shown on the display, “COMPLETE”is shown to inform you that the
settings have been saved.
2
Turn off the power using ON/STANDBY.
3
Press ON/STANDBY while simultaneously pressing SURROUND MODE and AUTO.
4
Once the display starts ashing at intervals of about 1 second, release the two
buttons.
5
Press and hold BAND and MENU for more than 3 seconds.
After “MEMORY LOAD” is shown on the display, “COMPLETE” is shown to inform you that the
settings have returned to those saved in step 1.
To return all of the settings to the default values, perform steps 2 to 4 without performing step 1.
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
GiPodH
Symptom Cause/Solution Page
iPod cannot be
played.
Check the iPod connections.
Switch the input source to “USB”.
Incompatible iPod types cannot be played back.
19
23
19
“Connection Error”
is displayed.
Unable to communicate properly. Turn off the power to this unit,
disconnect the iPod and then reconnect it.
“Not Support” is
displayed.
The iPod connected to the unit is not compatible. Please make
sure the iPod you are connecting is compatible.
The software version of the connected iPod is an old one. Please
update to the latest version.
19
“Connection Error”
is displayed.
The iPod is not responding. Turn off the power to this unit,
disconnect the iPod and then reconnect it.
When an iPod is
connected, “No
Connection” is
displayed.
“No Connection” may display if you connect an iPod that has
only a small amount of charge remaining in its battery to this unit.
Should this occur, charge the iPod before connecting it to this unit.
GM-XPortH
Symptom Cause/Solution Page
Audio is not output
when a wireless
receiver (RX101 is
connected).
Check that the Bluetooth device and Wireless receiver (RX101)
are correctly paired.
GRemote control unitH
Symptom Cause/Solution Page
The set cannot be
operated with the
remote control unit.
Batteries are worn out. Replace with new batteries.
Operate the remote control unit within a distance of about 23 ft /
7 m from this unit and at an angle of within 30°.
Remove any obstacle between this unit and the remote control
unit.
Insert the batteries in the proper direction, checking the q and
w marks.
The set’s remote control sensor is exposed to strong light (direct
sunlight, inverter type fluorescent bulb light, etc.). Move the set
to a place in which the remote control sensor will not be exposed
to strong light.
81
81
81
81
81
96


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR6005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR6005 in the language / languages: English as an attachment in your email.

The manual is 23,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR6005

Marantz SR6005 User Manual - Dutch - 96 pages

Marantz SR6005 User Manual - French - 104 pages

Marantz SR6005 User Manual - Spanish - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info