Manual Marantz SR6003 (page 33 of 90) (English)

61897

Zoom out

Zoom in

1/90

ENGLISH

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

SETUP

Audyssey MultEQ Setup

StartManual Setup

Main Zone Surround Back

Return

: Up / Down : Enter : OK Exit : Exit

: 2ch

“1st Mic Position Check”

The main listening position refers to the most

central position where one would normally

sit within the listening environment. MultEQ

uses the measurements from this position

to calculate speaker distance, level, polarity,

and the optimum crossover value for the

subwoofer.

Audyssey MultEQ Setup

Cancel

Speaker Check :

1st Mic Position

Now Analyzing!!

: : Enter : OK Exit : Exit

Note:

• The Speakers Check detects the presence of

connected speakers. If a channel is not used, the

SPEAKERS CHECK will try to detect it, then

continue to the next channel.

When the 1st Mic Position Check ends, the

following GUI appears on the display.

Audyssey MultEQ Setup

Start

Check

Calculate

Speaker Check : OK

2nd Mic Position

: Up / Down : Enter : OK Exit : Exit

Here, to view the results of the detection check,

select “Check” with the 3/4 cursor buttons and

press the ENTER button. The results will be

displayed.

2-1 AUTO SETUP (Audyssey MultEQ

)

AUTO SETUP (performed by Audyssey MultEQ)

automatically measures the acoustical problems in

the listening environment and optimizes settings to

create the best audio experience for your listening

environment.

Audyssey MultEQ removes frequency response

anomalies caused by the interaction of sound

from loudspeakers within the room. This results in

the playback of sound as it was intended, without

coloration, not just in one seat, but over a large

listening area.

Audyssey MultEQ measures up to 6 listening

positions in the room and detects the presence

of each speaker and automatically calculates the

speaker size, channel level, distance, and optimal

crossover frequency settings.

To set up the speaker system (i.e., adjusting speaker

distance, etc.) without using the AUTO SETUP feature,

see “MANUAL SETUP” on page 33 of the manual.

HOW TO PERFORM AUTO SETUP

During measurement, the GUI menu displays the

condition, therefore turn power to the monitor on.

Connect the supplied microphone to the

SETUP MIC jack on the unit.

Set the microphone in the main listening

position.

Notes:

• Up to 6 positions around the main listening position

can be measured.

For the ﬁ rst measurement, set the microphone in the

main listening position.

• Use a stand or tripod to position the microphone

at ear height for all listening positions measured

with the microphone tip pointing directly up to the

ceiling.

• Remove any obstructions between the speakers and

microphone.

• When using a powered subwoofer, set the level

knob to the middle or 12 o'clock position. Set the

crossover to off, or to its highest value.

If the subwoofer has a standby, or sleep mode, disable

it. Not doing so could affect the test signal which

may result in inaccurate subwoofer measurements.

• During measurements, do not stand between the

microphone and the speakers. Make the room as

quiet as possible. Background noise can disrupt

the room measurements. Close windows, silence

cell phones, televisions, radios, air conditioners,

ﬂ uorescent lights, home appliances, light dimmers,

or other devices.

Cell phones should be placed away from all audio

electronics during the measurement process as

Radio Frequency Interference (RFI) may cause

measurement disruptions (even if the cell phone is

not in use).

It is suggested to operate the AUTO SETUP via the

remote controller rather than by front panel.

• The test tones played through each channel increase

level as needed in order to overcome ambient noise

present in the listening environment and obtain the

best signal to noise ratio.

Select “Speaker Setup” from the Main Menu,

select “Auto Setup” with the 3/4 cursor

buttons, and press the ENTER button to

display the start screen.

Select the number of channels for the surround

back speaker you are using.

For a 5.1 channel speaker system, select “No”

(Surround Back speaker off). (To use speaker

C or Zone speaker, select “No”. See page 20,

38.)

Select “Start” with the 3/4 cursor buttons

and press the ENTER button to start

measurement.

Speakers Config

Check Speaker Results

Front Left

Center

Front Right

Surround Right

Surround Back Right

Surround Back Left

Surround Left

Subwoofer

Return

: : Enter : Return Exit : Exit

: Yes

: No

: Yes

: No

: Yes

If the check results indicate an error, take suitable

action with that item and remeasure. (For error

messages, see “ERROR MESSAGES” on

page 32.)

After confirming the check results, select

“Return” with the 3/4 cursor buttons and press

the ENTER button to return to the GUI menu.

At this point, you can select “Exit” to end Auto

Setup and return to “Speaker Setup”.

Note:

• Auto Setup is not available in Pure Direct, Source

Direct, or 7.1 Channel Input modes.

Move the microphone to the 2nd listening

position, select “Start” with the 3/4 cursor

buttons and press the ENTER button to

measure the 2nd point. At this point, you

can cancel second point measurement and

calculate measurement results by selecting

“Calculate” and pressing the ENTER button.

Audyssey MultEQ Setup

Start

Check

Calculate

Speaker Check : OK

2nd Mic Position

: Up / Down : Enter : OK Exit : Exit

SR6003_U_01_ENG 2_4.indd 30SR6003_U_01_ENG 2_4.indd 30 08.8.1 1:07:00 PM08.8.1 1:07:00 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR6003 in the language / languages: English as an attachment in your email.

The manual is 17,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR6003

Marantz SR6003 User Manual - Dutch - 73 pages

Marantz SR6003 User Manual - Spanish - 84 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Marantz SR6003 Manual

Product: