62526
62
Zoom out
Zoom in
Previous page
1/68
Next page
58
ENGLISH
TROUBLESHOOTING
In case of trouble, check the following before calling for service:
1. Are the connections made properly ?
2. Are you operating the unit properly following the user’s guide ?
3. Are the power amplifi ers and speaker working properly ?
If the unit does not operate properly, check items shown in the following table.
If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the
internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz
authorized dealer or the Marantz Service Center in your country.
SYMPTOM CAUSE REMEDY
SR6001 cannot be turned
up.
The power plug is not connected.
Connect the power plug to the outlet.
No sound and picture are
output even when power is
on.
Mute is on.
Cancel mute using the remote control unit.
The input cable is not connected
correctly.
See the connection diagram and connect the cables
correctly.
The master volume control is turned all
the way down.
Adjust the master volume.
The function selector position is wrong.
Select correct position.
No speaker output. The headphones are connected to the
headphone jack.
Disconnect the headphones. (Speakers will not
output sound when headphones are connected.)
Incorrect Audio or Video for
selected source.
Input cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Incorrect Audio from a
channel.
Speaker cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
No Audio output from the
center channel speaker.
The center speaker cable connection is
incomplete.
Connect the cable correctly.
STEREO has been selected for Surround
mode.
When STEREO is selected for Surround mode, no
sound will be output from the center speaker. Set
another Surround mode.
Center = NONE has been selected in
SETUP mode.
Make the correct setting.
No Audio output from the
surround speakers.
The surround speaker cable connection
is incomplete.
Connect the cable correctly.
STEREO has been selected for Surround
mode.
When STEREO has been selected for Surround
mode, no sound will be output from the surround
speaker. Set another Surround mode.
Surround = NONE has been selected in
SETUP mode.
Make the correct setting.
No Audio output from the
surround back speakers.
The surround back speaker cable
connection is incomplete.
Connect the cable correctly.
Surround mode is not EX/ES mode.
Set surround mode EX/ES.
Surround back = NONE has been
selected in SPEAKERS SIZE SETUP
Make the correct setting.
SYMPTOM CAUSE REMEDY
Can not select EX/ES mode. Surround center= NONE has been
selected in SPEAKERS SIZE SETUP
Make the correct setting.
Input signal is incompatible.
Use 5.1channel source.
Can not select Pro Logic IIx
mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select Neo:6 mode. Input signal is incompatible.
Use 2 channel DTS input signal, PCM input signal or
analog input signal.
Can not select CSII mode. Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
No output to Subwoofer Out. Subwoofer = NONE has been selected
in SETUP mode.
Select Subwoofer = YES.
Noise is produced during
DTS-encoded CD or laser
disc play.
Analog has been selected for input.
Be sure to perform digital connection, select digital
input, then play.
A specifi c channel does not
produce output.
Nothing recorded on source.
Check the encoded channel on the source side.
FM or AM reception fails. Antenna connection is incomplete.
Correctly connect the indoor FM and AM antennas
to FM and AM antenna outlets.
Noise is heard during AM
reception.
Reception is affected by other electrical
elds.
Try changing location where the AM indoor antenna
is set up.
Noise is heard during FM
reception.
The radio waves from the broadcasting
station are weak.
Install an FM outdoor antenna.
Cannot get programmed
station when the PRESET
button is pressed.
Preset data has been erased.
Disconnecting power plug for long periods of time
will erase preset data. If that happens, input the
preset data again.
Control with the remote
control unit fails.
Batteries are consumed.
Replace all the batteries with new ones.
Remote controller's function-key setting
is wrong.
Select different position from which equipment will
be controlled.
The distance between this SR6001 and
the remote commander is too far.
Move closer to this SR6001.
Something is blocking SR6001 and the
remote commander.
Remove offending object.
Auto Setup (SPEAKER
SETUP) is not working.
Headphones are connected.
Disconnect the headphones.
Note:
• After “PROTECT” appears on the unit’s display, the standby indicator may start fl ashing. If it does, there is a
problem in the unit or the connection. If this problem reoccurs even when power is activated from the remote control
unit, call for servicing.
SR6001N DFU_1_ENG 4_4.indd 58SR6001N DFU_1_ENG 4_4.indd 58 06.12.21 3:12:21 PM06.12.21 3:12:21 PM
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR6001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR6001 in the language / languages: English as an attachment in your email.

The manual is 5,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info