62526
35
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISH
31
Note:
The detection check measures the state of use of all
speakers whether actually used or not.
For example, if the center speaker is not used, the
test tone will require time to go from the L-channel
to the R-channel, therefore be careful not to unplug
the microphone or operate the SR6001 during this
time.
6.
When the detection check ends, the following
OSD appears on the display.
AUTO SETUP
SPEAKERS CHECK:OK
1ST MIC POSITION!!
START
CHECK
EXIT
Here, to view the results of the detection check,
select “CHECK with the 3/4 cursor buttons
and press the ENTER button. The results will
be displayed.
SPEAKER CONFIG
CHECK !! SPEAKER
FRONT : YES
CENTER : NON
FRONT R : YES
SURR.R : YES
SURR.B R : NON
SURR.B L : NON
SURR.L : YES
SUB W : YES
RETURN EXIT
If the check results indicate an error, take suitable
action with that item and remeasure. (For error
messages, see “ERROR MESSAGES” on
page 33.)
After confirming the check results, select
RETURN with the 3/4 cursor buttons and
press the ENTER button to return to the OSD
menu.
At this point, you can select EXIT” to end Auto
Setup and return to “2. SPKR SETUP”.
2-1 AUTO SETUP (MultEQ™ SETUP)
The AUTO SETUP (MultEQ™ Setup) feature of
the SR6001 measures sound characteristics of the
speaker system and room where the receiver is used
and automatically optimizes settings.
The Audyssey MultEQ™ technology adopted by the
SR6001 provides the best listening environment for
multiple listeners.
To do this, the AUTO SETUP feature measures a
test tone emitted by each channel in a maximum of 6
listening positions, using the supplied microphone.
The measurement results are analyzed using an
original algorithm and environmental settings are
made to improve the sound characteristics of the
listening area.
To set up the speaker system (i.e., adjusting speaker
distance, etc.) without using the AUTO SETUP feature,
see “MANUAL SETUP” on page 34 of the manual.
HOW TO PERFORM AUTO SETUP
During measurement, the OSD menu displays the
condition, therefore turn power to the monitor on.
1.
Connect the supplied microphone to the MIC
jack on the SR6001.
AV SURROUND RECEIVER SR6001
POWER ON/OFF PHONES
STANDBY
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
DISP MULTI AUTO TUNED ST SPKR A B V-OFF
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MT X 6.1
PCM
AAC
AUX 1 INPUT
AUDIOS-VIDEODIGITAL VIDEO L R
DOWN
UP
VOLUME
ENTER
INPUT SELECTOR
HT-EQ
HT-EQ
2.
Set the microphone in the listening position.
Notes:
Measurement can be done in a maximum of 6
listening positions.
For the fi rst measurement, set the microphone in the
main listening position.
Use a stand or tripod to position the microphone at
ear height in the listening position.
Remove any obstructions between the speakers and
microphone.
• To use the internal subwoofer of the amp, set the
volume to the middle point and set the crossover
frequency to the highest.
During measurement, step away from the microphone
and operate the SR6001 via the remote control unit
from a position that is out of the path of the speaker
sound.
The test tone output from the speakers during
measurement is loud. Be mindful of neighbors and
watch out for small children.
3.
Either press the MultEQ™ button on the
front panel of the SR6001 or select “2. SPKR
SETUP” from the MAIN MENU, select AUTO
SETUP with the 3/4 cursor buttons, and press
the ENTER button to display the start screen.
4.
Select the number of channels for the surround
back speaker you are using.
For a 5.1 channel speaker system, select
“NON” (Surround Back speaker off). (To use
speaker C or multi speaker, select “NON”. See
page 23, 40.)
Select START” with the 3/4 cursor buttons
and press the ENTER button to start
measurement.
AUTO SETUP
AUTO SETUP: START
MAIN ROOM
SURR BACK: 2CH
RETURN EXIT
5.
Detection Check
During the detection check, the following OSD
appears on the display and checks are made
to detect dark sound in the listening room,
whether there are speakers or not and polarity.
AUTO SETUP
SPEAKERS CHECK:--
NOW ANALYZING !!
CANCEL
EXIT
7.
Calibration Check
AUTO SETUP
SPEAKERS CHECK:OK
1ST MIC POSITION!!
START
CHECK
EXIT
Select START” with the 3/4 cursor buttons
and press the ENTER button to measure the
rst point (main listening position).
During measurement, the following OSD
appears on the display. At this point, you can
cancel measurement by selecting CANCEL
with the 3/4 cursor buttons and pressing the
ENTER button.
AUTO SETUP
NOW ANALYZING!!
CANCEL
EXIT
When this measurement ends, the following
OSD appears on the display
AUTO SETUP
SPEAKERS CHECK:OK
2ND MIC POSITION!!
START
CALCULATE
EXIT
SR6001N DFU_1_ENG 2_4.indd 31SR6001N DFU_1_ENG 2_4.indd 31 06.12.21 3:10:55 PM06.12.21 3:10:55 PM
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR6001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR6001 in the language / languages: English as an attachment in your email.

The manual is 5,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info