522801
45
Zoom out
Zoom in
Previous page
1/96
Next page
NAMES AND
FUNCTIONS
43
BASIC
CONNECTIONS
BASIC
OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
ADVANCED
OPERATION
ENGLISH
ADVANCED OPERATION
LIP.SYNC
Depending on the image device (TV, monitor,
projector, etc.) connected to the unit a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the unit
to correct the time lag between the sound and
image. It can be operated with the “LIP SYNC” and
1 and 2 cursor buttons of the remote controller.
Set the remote controller to the AMP mode before
operating the LIP.SYNC feature. The initial setting is
OFF (0 ms).The time lag can be adjusted in 10 ms
steps up to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Notes
The LIP.SYNC feature turns OFF (0 ms) in
the SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYNC feature is automatically
restored.
Even if you do not correct the time lag manually
this way, audio and video are automatically
synchronized when the unit is connected to TV
or Projector supporting Auto Lipsync Correction
in HDMI 1.3a. For instructions on Auto Lipsync
Correction, see page 36.
USING THE SLEEP TIMER
To program this unit for automatic standby, press
the SLEEP button on the remote controller.
Each press of the button will increase the time
before shut down in the following sequence.
OFF 10 20 30 5040
100 90 80 70 60110120
The sleep time will be shown for a few seconds in
the display on the front panel, and it will count down
until the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows “SLEEP OFF” and
the SLEEP indicator will disappear.
FRONT KEY (BUTTON) LOCK OF THE UNIT
To lock all front panel buttons (except the POWER ON/
OFF button) and the INPUT SELECTER and VOLUME
knobs, hold the PURE DIRECT and EXIT buttons on
the front panel simultaneously for at least 3 seconds.
At this time, “F-KEY LOCK!” is displayed.
To unlock the controls, press the same buttons
again simultaneously for at least 3 seconds. At
this time, “F-KEY UNLOCK” is displayed, and the
buttons are released.
SURR.
MODE
PURE
DIRECT
EXIT CLEAR
DUAL BACKUP MEMORY
The unit stores settings information in nonvolatile
memory even when the main power supply is turned
off. Using the Dual Backup Memory function, you
can write settings information to another memory
area to back up saved settings for recovery anytime
as needed.
BACKUP
Set up the unit in the state for which you want to
store the settings. Hold the MEMORY and ENTER
buttons on the front panel simultaneously for at
least 3 seconds.
“MEMORY SAVING” is displayed and the unit’s
settings are saved. The stored settings information
is retained until Dual Backup Memory is used again
and the information is overwritten.
MEMORY SAVING
Note
The following settings values cannot be backed up,
each Volume value is set to Minimum.
Main ZONE Volume
• ZONE A Volume
• ZONE Speaker A Volume
RECOVERY OF MEMORY
Recover backed up settings as follows.
Hold the MEMORY and MENU buttons on the front
panel simultaneously for at least 3 seconds.
“MEMORY LOAD” is displayed and the unit’s
stored settings are reapplied.
The unit temporarily enters standby mode. If there
is no backup data, “NO BACKUP” is displayed and
no data is recovered.
MEMORY LOAD
NO BACKUP
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR5004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR5004 in the language / languages: English as an attachment in your email.

The manual is 21,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info