43
ENGLISH
(Using the remote controller)
1.
Press the P.SCAN on the remote controller.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled fi rst.
2.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3.
You can fast forward the preset stations by
pressing the T continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P.SCAN on the remote
controller.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
CAT
P.SCAN
CAT
T.MODE
123
456
789
0
+10
HT-EQ
MULTI/
MENU
SPKR A/B
INFO
CH/
INPUT
M-SPKR
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
A/D
LIP SYNC/
CLCL
MEMOMEMO
2.
3.
DIGITAL
VIDEO
S-VIDEO
AUX 1 INPUT
T-MOD E
MEMORY
DISPLAY
MUTE
VOLUME
DOWN
EXIT
BAND
CLEAR
ENTER
2. 3.
1.
Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller.
3.
The stored preset number blinks in the display
for 5 seconds. While blinking, press the
CLEAR button on the front panel or the remote
controller
.
4.
“xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
Note:
To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
(Using the remote controller)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMO button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
RECALLING A PRESET STATION
P.SCAN
T.MODE
+10
11 22 33
44 55 66
77 88 99
00
CAT CAT
HT-EQ
SPKR A/B
INPUT
MUTE
EX/ES
VIRTUAL
CS
VOLUME
dts
P.DIRECT
7.1CH IN
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
DISPLAY
A/D
LIP SYNC/
MEMO
CL
CH/CH/
1.
SETUP
SIMPLE
PURE
T-MOD E
SURROUND
MEMORY
DISPLAY
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
1.
-
AUDIO
ANGLE
SUB TITLE
DISC+
1.
(Using the unit)
1.
Select the desired preset station by pressing
the 1 or 2
cursor
buttons on the front panel
(Using the remote controller)
1.
Press the S or T buttons to select the
desired preset station, or input your desired
preset channel with the numeric buttons on
the remote controller.
PRESET SCAN
T.MODE
456
789
0
+10
P.SCANP.SCAN
CAT CAT
HT-EQ
SPKR A/B
MUTE
EX/ES
VIRTUAL
CS
VOLUME
7.1CH IN
STEREO
NIGHT
M-CH ST
A/D
MEMO
CH/CH/
CLCL
1.
3.
3.
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
++
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
3.
1.
Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller for more than 3 seconds.
3.
The left most column of the station name
indicator fl ashes, indicating the character entry
ready status.
4.
When you press the 3 or 4 cursor buttons
on the front panel or the 5 / 6 buttons on
the remote controller, alphabetic and numeric
characters will be displayed in the following
order:
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
← DOWN
5.
After selecting the fi rst character to be entered,
press the MEMORY or ENTER buttons, press
the MEMO button on the remote controller.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the
same way.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press S or
T buttons on the remote controller.
Note:
Unused columns should be fi lled by entering blanks.
6.
To save the name, press the MEMORY button
on the front panel or remote controller for more
than 2 seconds.
Ten keypad Press, press again, press again, etc.
1
A
→
B
→
C
→
1
→
A
2
D
→
E
→
F
→
2
→
D
3
G
→
H
→
I
→
3
→
G
4
J
→
K
→
L
→
4
→
J
5
M
→
N
→
O
→
5
→
M
6
P
→
Q
→
R
→
6
→
P
7
S
→
T
→
U
→
7
→
S
8
V
→
W
→
X
→
8
→
V
9
Y
→
Z
→
space
→
9
→
Y
0
–
→
+
→
/
→
0
SORTING PRESET STATIONS
MULTI
SPEAKER
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
SETUP
SIMPLE
MULTI
PURE
T-MODE
SURROUND
MEMORY
DISPLAY
ATT
MUTE
STANDBY
INPUT SELECTOR
VOLUME
UP
DOWN
AV SURROUND RECEIVER SR5002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
PHONES
POWER ON/STANDBY
SETUP MIC
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 5:
To sort the numbers, press the 4 cursor button while
pressing the MEMORY button.
“PRESET SORT” will appear on the display and
sorting will be done.
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
CAT
-
T.DISP
F.DIRECT
PTY
PRESET
+
789
0
+10
CAT CAT
TUNINGTUNING
--
++
HT-EQ
MULTI/
MENU
SPKR A/B
EXIT
INFO
T.TONE
/SET UP
M-SPKR
MUTE
DVD VCR
DSS
TV
VOLUME
BASS
TREBLE
7.1CH IN
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
A/D
CL
ENTERENTER
MEMOMEMO
CH/CH/
2. 5. 6.
5.
4.
MULTI
SPEAKER
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
SETUP
SIMPLE
MULTI
PURE
T-MOD E
SURROUND
MEMORY
DISPLAY
ATT
MUTE
STANDBY
INPUT SELECTOR
VOLUME
UP
DOWN
AV SURROUND RECEIVER SR5002
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
PHONES
POWER ON/STANDBY
SETUP MIC
5. 2.
5.
6.
4.
SR4002-5002U DFU_01_E2_2.indd 43SR4002-5002U DFU_01_E2_2.indd 43 07.7.9 2:47:40 PM07.7.9 2:47:40 PM
