61338
31
Zoom out
Zoom in
Previous page
1/48
Next page
28
ENGLISH
BASIC
CONNECTIONS
BASIC OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTIONS
ADVANCED
OPERATION
ATTENUATION TO ANALOG INPUT SIGNAL
If the selected analog audio input signal is greater
than the capable level of internal processing, the
PEAK indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote controller.
ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD/CDR-OUT and VCR-OUT.
This function is memorized for each individual input
source.
7.1 CH INPUT
This unit is equipped for future expansion through the
use of Multi channel Super Audio CD multichannel
player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources.
2
.
4
.
1
.
DISP MULTI AU TO TUNED ST V
OFF NIGHT PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1 MTX 6.1 SPKR B EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL S SR
LFE
1. 4.
3
.
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press the 7.1 button on the remote controller to
switch the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote controller.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOLUME buttons on the remote
controller.
To cancel the 7.1 CH. INPUT setting, press 7.1 on the
remote controller.
Notes:
7.1 CH. Input mode bypasses the internal surround
processing, so SURROUND mode cannot be
selected.
In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
DISP MULTI AU TO
SLEEP
SURR
AUTO
HT-EQ (HOME THEATER EQUALIZER)
1.
2.
At cinemas, the front left, front right and center
speakers are located behind the screen. So, screen
damping is taken into account when mastering movie
software, with an emphasis on high frequencies.
When playing back such software at home, the
signal takes on different characteristics from those
at the cinema. This unit includes HT-EQ to rectify
the sound difference between that experienced at a
cinema and in a home theater, allowing you to enjoy
the same sound you would experience at the cinema
at home. The HT-EQ feature is available except in the
following modes.
7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
When VIRTUAL is set for the surround mode
1.
Press the HT EQ button on the remote
controller.
“EQ” indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER
has been activated.
2.
To cancel this function, press the HT EQ button
again.
“EQ” indicator on the front panel will be
turned off, indicating the HOME THEATER
EQUALIZER has been deactivated.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
page 22 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
unit.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, this unit turns ON
and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2.
The power to the unit switches to STANDBY
after approx. 5 minutes.
Notes:
AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
The S-Video terminal does not support “TV AUTO
ON/OFF” function.
SR4003_U_01_E2_2.indd 28SR4003_U_01_E2_2.indd 28 08.6.20 5:06:29 PM08.6.20 5:06:29 PM
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR4003 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR4003 in the language / languages: English as an attachment in your email.

The manual is 7,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR4003

Marantz SR4003 User Manual - Dutch - 43 pages

Marantz SR4003 User Manual - Spanish - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info