522884
39
Zoom out
Zoom in
Previous page
1/56
Next page
36
ENGLISH
OTHER FUNCTION
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the SR4001/SR5001.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
page 27 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
SR4001/SR5001.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, the SR4001/
SR5001 turns ON and TV is selected
automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2.
The power to the SR4001/SR5001 switches to
STANDBY after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the SR4001/
SR5001 is set to a source other than TV.
The function reactivates when TV is selected again.
Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
The S-Video terminal does not support “TV AUTO
ON/OFF” function.
ATTENUATION TO ANALOG INPUT SIGNAL
-
T
.
DISP
F
.
DIRECT
PTY
TUNING
PRESET
-
++
MD
CDR
CD
DVD VCR
TUNER
DSS
TV
BASS
TREBLE
REC
AUDIO
ANGLE
DISC+
CH-SEL
V-OFF
SUB TITLESUB TITLE
ATT.ATT.
If the selected analog audio input signal is greater
than the capable level of internal processing, the
PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote.
ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT
and DSS/VCR2-OUT.
This function is memorized for each individual input
source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR4001/
SR5001’s output through a pair of headphones.
Be certain that the headphones have a standard
1/4” stereo phono plug. (Note that the speakers will
automatically be turned off when the headphone jack
is in use.)
MULTI
SPEAKER
SETUP
SIMPLE
MULTI
PURE
SURROUND
STANDBY
PHONES
POWER ON/STANDBY
INPUT SELECTOR
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
MENU
MODE
Note:
The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.
HEAD PHONE
DOLBY HP MODE : ON
SURROUND : OFF
L LEVEL : 0 dB
R LEVEL : 0 dB
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS ON BYPASS
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
ON: Dolby headphone mode active.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “✽✽✽” is
displayed as the mode indication.
The surround mode can be selected when mode is
ON.
L/R LEVEL can be set in the ±10 dB range.
Notes:
The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
TONE cannot be set when mode is ON.
The Dolby Headphone function will not work when
32 or 96 kHz PCM digital signals are input.
VIDEO ON/OFF
When no video signal is connected to the SR4001/
SR5001 or a DVD, etc., is connected directly to your
TV, the unnecessary video circuit can be turned off
by selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V-OFF button.
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AUX2
VCR
TUNER
DSS
TV
AUX1
AMPAMP
-
TUNING
PRESET
-
++
DVD VCR
DSS
TV
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
SETUP
SIMPLE
PURE
T-MODE
SURROUND
MEMORY
DISPLAY
R
5001
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
DISPLAY MODE
P.SCAN
T.MODE
123
456
789
SEND
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
OFF
ON
SET
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
LEARN
LIP SYNC/
SOURCE
DISPLAYDISPLAY
SETUP
SIMPLE
PURE
T-MODE
SURROUND
MEMORY
DISPLAY
E
R SR5001
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
You can select the display mode for the front display
of the SR4001/SR5001.
To select this mode, press the DISPLAY on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
Surround Mode Auto-display Off Display Off
Input Function Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display in display off condition
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR4001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR4001 in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info