570389

Marantz SR12S1 Manual

37
Zoom out
Zoom in
Previous page
1/58
Next page
34
ENGLISH
SPEAKERS LEVEL
Here you will set the volume for each speaker so that they are all
heard by the listener at the same level.
Note:
• The speaker level settings is not available in 7.1channel input
mode and S-Direct mode.
TEST MODE : Selects “MANUAL” or “AUTO” for generating mode of
test tone Left or Right cursor button.
If you select “AUTO” , the test tone will be cycled through in a circular
pattern which is Left → Center → Right → Surround Right → Surround
Back Right → Surround Back Left → Surround Left → Subwoofer →
Left →.. increments of 3 seconds for each channel.
Using the Left and Right cursor buttons, adjust the volume level of the
noise from the speaker so that it is the same level for all speaker.
If you select “MANUAL”, adjust the output level of each speaker as
follow.
1.
When you move cursor to FRONT L by pressing Down cursor
button, the SR-12S1 will emit a pink noise from the front left
speaker.
At this time, the master volume automatically increases to the
reference level (0 dB).
Remember the level of this noise and then press the Down cursor
button.
(Note that this can be adjusted to any level between -10 and +10
dB in 1 dB intervals.)
The SR-12S1 will now emit the pink noise from the center
speaker.
2.
Using the Left and Right cursor buttons, adjust the volume level
of the noise from the center speaker so that it is the same level as
the front left speaker.
3.
Press the Down cursor button again. The SR-12S1 will now emit
the pink noise from the front right speaker.
4.
Repeat steps 2 and 3 above for the front right and other speakers
until all speakers are adjusted to the same volume level.
If you finish these setup, press OK button, the cursor will move to
“NEXT” and then press OK button to go to next page.
Notes:
• Speakers that you selected “No” or “None” for in the Speaker
Size menu will not appear.
• The setting of Surr.Back L and Surr.Back R appears if set for
two surround back speakers in the Speaker Size menu.
• The setting of Surr.Back appears if set for one surround back
speaker in the Speaker Size menu.
• The setup level for each channel is memorized for reproduction
in all surround mode.
• To adjust the speaker levels for 7.1-channel input sources, you
will need to use the 7.1CH-INPUT sub menu. (See page 37).
• In order to correctly set the output levels, use a hand-held Sound
Pressure Level meter (SPL), set to C-Weighting and Slow
averaging. A Radio Shack
®
SPL meter (catalogue number 330
- 2055) works well. Using the internal channel noise
generators, set each channel so that you read 75 dB SPL from
each channel when seated at the listening position.
BASS PEAK LEVEL
With Dolby Digital and DTS , not only the LFE (Low Frequency
Effects), but also the bass of all channels can be heard from the
Subwoofer or Large-speakers. This procedure prevents these
speakers from becoming too loud and creating an unbalanced sound.
Since the sound is output at a loud volume, perform this operation
carefully.
Note:
• If your system does not include a subwoofer, this setting will set
the bass peak level for your front speakers.
TEST SIGNAL: Press the OK or Left button, START is indicated and
it begins to generate a Bass test tone from the
speaker which was designated “bass signal output”
during setup.
There will be no audible sound yet because the
Master volume is set to minimum automatically.
Press Down cursor button to move the cursor to
VOLUME control.
VOLUME: Adjust the bass test tone output level up until the
bass begins to distort or you reach the maximum
level with the VOL+, VOL– or Right / Left cursor
button.
Press Down cursor button to move the cursor to
ENTER.
ENTER: Press the OK button, ENTER will blink and stop
generating the Bass Peak test tone.
The Bass Peak Limit Level for your system has now
been memorized.
If you finish these setup, move cursor to “MAIN” with Up or Down
cursor button and then press OK button to go to MAIN menu.
Notes:
• Each time the subwoofer level is changed, perform the Bass
Peak Level setup and correct the setting.
• The bass peak level is not available in SOURCE-DIRECT and
7.1CH-INPUT mode.
• The selected value is displayed in the volume column before the
test signal starts.
2-5 BASS PEAK LEVEL
BASS PEAK TEST : START
VOLUME LEVEL : + 18dB
--------------------
ENTER
MA I N R E T U RN E X I T
2-4 SPEAKERS LEVEL
TEST MODE :MANUAL
FRONT L : 0 dB
CENTER : 0 dB
FRONT R : 0 dB
S URR . R : 0 dB
S URR . B R : 0 dB
S URR . B L : 0 dB
S URR . L : 0 dB
SUB W : 0 dB
MA I N RE TURN NEXT EX I T
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR12S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR12S1 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR12S1

Marantz SR12S1 Additional guide - English - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info