6614
59
Zoom out
Zoom in
Previous page
1/68
Next page
57
ENGLISH
ENGLISH
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from a
compact disc player connected to CD IN and the
video from a video camera connected to VCR1 to
video cassette recorder connected to the VCR2/
DVD-R OUT jack.
1.
Switch the video input source to VCR1 by
tapping the VCR1 on page 1/8 on the remote
control unit.
2.
Switch the audio input source to CD by
tapping the CD on page 1/8 on the remote
control unit.
3.
CD is now selected as the audio input
source and VCR1 as the video input source.
Notes:
If you change the input source during recording,
you will record the signals from the newly
selected input source.
You cannot record surround effects.
Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog.
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
1/8 A/V Amp
Source Select
wed Jun 01 4:40pm
1.
2.
Adjust the speaker output levels so that you
can hear the same sound level from each
speaker at the listening position. For the front
left, front right, center, surround left, surround
right and surround back speakers, the output
levels can be adjusted between 12 to +12 dB.
The subwoofer can be adjusted between 18
and +12 dB.
These adjustments result will be stored to the
7.1 CH. Input memory.
3.
Adjust the main volume with the VOLUME
control knob on the front panel or the VOL
/
buttons on the remote.
To cancel the 7.1 CH. Input setting, press the 7.1
CH INPUT button on the front panel or tap the 7.1
input off on the remote control unit.
Notes:
When the 7.1 CH. Input mode is activated, you
may not select a surround mode, as the external
decoder determines processing.
In addition, there is no signal sent to the record
outputs when the 7.1 CH. Input mode is activated.
The SR9600 has two input modes: 5.1 channel
and 7.1 channel. Set the input mode on the 7.1 CH
INPUT SETUP menu. (See page 33)
5.1 Channel Input mode:
Surround processing such as for THX music is
performed for 5.1 channel input, excluding
surround back left and right channels.
7.1 Channel Input mode:
Surround processing is not performed for 7.1
channel analog input.
7.1 CH INPUT
The SR9600 is equipped for future expansion
through support for SACD multichannel or DVD-
Audio players.
When this is selected, the input signals connected
to the L (front left), R (front right), C (center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right) channels
of the 7.1 CH. In jacks are output directly to the
front (left and right), center, surround (left and
right) and surround back speaker systems as well
as the pre-out jacks without passing through the
surround circuitry.
I
n addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
The video input source for 7.1 channel input is set
on the 7.1 CH INPUT SETUP menu. (See page 33)
This permits simultaneous viewing with video
sources.
1.
Press the 7.1 CH INPUT button on the front
panel or tap the 7.1 input on (
page 1/8
) on the
remote control unit to switch to 7.1 channel
input.
2.
If it is necessary to adjust the output level of
each channel, tap the CH Sel and Ch Level
(
PAGE6/8
) on the remote control unit.
MULTIMULTI
SPEAKERSPEAKER
F/PBANDTHXTHXPURE DIRECTPURE DIRECT UPUP
DOWNDOWN
TUNINGTUNING
AUX 1 INPUT
RAUDIO
DIGITAL S-VIDEO
LVIDEO
POWER ON/STANDBY
VOLUME
UPDOWN
INPUT SELECTOR
PHONESPHONES
STANDBY
RROUND RECEIVER SR9600AV SURROUND RECEIVER SR9600
SURROUNDSURROUND
MIC
ENTERENTER
MENUMENU
PURE DIRECTPURE DIRECT THXTHX
7.1CH INPUT7.1CH INPUT
MODEMODE AUTOAUTO
MULTIMULTI
A/B
T-MODET-MODE
MEMORY CLEAR
DISPLAYDISPLAY
EXITEXIT
SPEAKERS
MRAC
AUTO TUNEAUTO TUNE
1.
1/8 A/V Amp
Source Select
wed Jun 01 4:40
pm
1.
6/8 A/V Amp
Tone Adjust
wed Jun 01 4:40pm
2.
MULTI
SPEAKER
F/PF/PBANDBANDTHXPURE DIRECT PUP
DOWN
TUNING
AUX 1 INPUTAUX 1 INPUT
RRAUDIOAUDIO
DIGITALDIGITAL S-VIDEOS-VIDEO
LLVIDEOVIDEO
POWER ON/STANDBY
VOLUMEVOLUME
UPUPDOWNDOWN
INPUT SELECTOR
PHONES
STANDBY
AV SURROUND RECEIVER SR9600
SURROUND
MICMIC
ENTER
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/BA/B
T-MODET-MODE
MEMORYMEMORY CLEARCLEAR
DISPLAYDISPLAY
EXITEXIT
SPEAKERSSPEAKERS
MRACMRAC
TO TUNEAUTO TUNE
3.
H
Ex
M
S
VOL
CH
OK
3.
SPEAKER A/B
The SR9600 allows you to select speaker system A
and speaker system B for the front L/R channels.
You can select these systems by pressing the
SPEAKERS A/B button on the front panel or by
tapping Spk-A on/off and Spk-B on/off (page 7/8)
on the remote control unit.
AUX2 INPUT
If you dont need to connect 7.1 channel input
terminals for multichannel decoding, the L (front
left) and R (front right) input terminals can be used
for AUX2 input.
In this case, you can connect additional audio
sources to AUX2.
1.
To select AUX2, turn the INPUT SELECTOR
knob on the front panel.
Tap the A/V Amp on the remote control unit
and press the page up button until page 1/8 is
displayed. Tap the AUX2 on the remote
control unit.
MULTIMULTI
SPEAKERSPEAKER
F/PF/PBANDBANDTHXPURE DIRECT UPUP
DOWNDOWN
TUNINGTUNING
AUX 1 INPUTAUX 1 INPUT
RAUDIODIGITALDIGITAL S-VIDEOS-VIDEO LVIDEOVIDEO
POWER ON/STANDBY
VOLUMEVOLUME
UPDOWNDOWN
INPUT SELECTOR
PHONES
STANDBY
AV SURROUND RECEIVER SR9600
SURROUND
MICMIC
ENTERENTER
MENUMENU
PURE DIRECT THX
7.1CH INPUT7.1CH INPUT
MODE AUTO
MULTIMULTI
A/BA/B
T-MODET-MODE
MEMORYMEMORY CLEARCLEAR
DISPLAYDISPLAY
EXITEXIT
SPEAKERSSPEAKERS
MRACMRAC
AUTO TUNEAUTO TUNE
7/8 A/V Amp
Speaker A/B
wed Jun 01 4:40
pm
1/8 A/V Amp
Source Select
wed Jun 01 4:40
pm
1.
MULTI
SPEAKER
F/PBANDTHXTHXPURE DIRECTPURE DIRECT UP
DOWN
TUNING
AUX 1 INPUT
RAUDIO
DIGITAL S-VIDEO
LVIDEO
POWER ON/STANDBYPOWER ON/STANDBY
VOLUME
UPDOWN
INPUT SELECTORINPUT SELECTOR
PHONESPHONES
STANDBYSTANDBY
AV SURROUND RECEIVER SR9600AV SURROUND RECEIVER SR9600
SURROUNDSURROUND
MIC
ENTER
MENU
PURE DIRECTPURE DIRECT THXTHX
77.1CH INPUT
MODEMODE AUTOAUTO
MULTMULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
MRAC
AUTO TUNE
1.
MULTI
SPEAKER
F/PBANDTHXPURE DIRECTPURE DIRECT UP
DOWN
TUNING
AUX 1 INPUT
RAUDIO
DIGITAL S-VIDEO
LVIDEO
POWER ON/STANDBYPOWER ON/STANDBY
VOLUME
UPDOWN
INPUT SELECTORINPUT SELECTOR
PHONESPHONES
STANDBYSTANDBY
AV SURROUND RECEIVER SR9600AV SURROUND RECEIVER SR9600
SURROUNSURROUND
MIC
ENTER
MENU
PURE DIREPURE DIRECT THX
7.1CH INPUT
MODEMODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
MRAC
AUTO TUNE
1.
SR9600U DFU_01_ENG 4_4 05.4.27, 5:48 PMPage 57 Adobe PageMaker 6.5J/PPC
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-9600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-9600 in the language / languages: English as an attachment in your email.

The manual is 10,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info