6614
52
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISH
50
NIGHT MODE
1.
Tap the Night on the remote control unit to
turn on the Night mode.
Setting the Night mode to ON compresses
the dynamic range in Dolby Digital only.
This softens loud passages such as sudden
explosions, to help prevent disturbing others
late at night.
2.
To turn off the Night mode, tap the Night again.
DIALOGUE NORMALIZATION
MESSAGE
Dialogue Normalization (Dial Norm) is a feature of
Dolby Digital.
When playing back software which has been
encoded in Dolby Digital, sometimes you may see
a brief message on the FL display which will read
"Dial Norm X dB" (X being a numeric value).
Dialogue Normalization serves to let you know if
the source material has been recorded at a higher
or lower level than usual. For example, if you see
the following message: "Dial Norm + 4 dB" on the
FL display, to keep the overall output level
constant just turn down the volume control by 4 dB.
In other words, the source material that you are
listening to has been recorded 4 dB louder than
usual.
If you do not see a message on the FL display,
then no adjustment of the volume control is
necessary.
RE-EQ
This menu is for turning THX Cinema Re-EQ on
and off. The tonal balance of a film soundtrack will
be excessively bright and harsh when played back
over audio equipment in the home. This is because
film soundtracks were designed to be played back
in large movie theater environments.
Activating the Cinema Re-EQ mode when
watching a film made for movie theaters corrects
this and restores the correct tonal balance.
Cinema Re-EQ is therefore not necessary for
material that was not designed for movie theaters
(for example, sports programming, television
shows, made for TV movies, etc.).
The Cinema Re-EQ mode can be activated only
while in Dolby Pro Logic mode, or while decoding
Dolby Digital or DTS-encoded material.
1.
Tap the Re EQ on the remote control unit to
turn on the Re-EQ mode.
2.
To turn off the Re-EQ mode, tap the Re EQ
again.
Note:
The Re-EQ mode can be selected from the OSD
menu system. (See page 41)
LIP.SYNC
Depending on the display component (TV, monitor,
projector, etc.) connected to the SR9600, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The Lip.Sync mode delays the audio signal with
respect to the image signal output from the SR9600
to correct the time lag between the sound and
image.
1.
Tap the A/V Amp and press the page up
button until page 5/8 is displayed. Tap the L-
Sync on the remote control unit.
2.
Select the time lag with the and cursor
buttons on the remote control unit.
The initial setting is OFF (0 ms). The time lag can
be adjusted in 10 ms increments up to 200 ms.
Watch the picture on the image device (e.g., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
The Lip.Sync mode is set to OFF (0 ms) in the
Pure Direct and Source Direct mode.
When the
Pure Direct (or Source Direct) mode is deactivated,
the previously set value of the Lip. Sync
mode
is
automatically restored.
5/8 A/V Amp
Mode
wed Jun 01 4:40
pm
1.
5/8 A/V Amp
Mode
wed Jun 01 4:40
pm
1.
5/8 A/V Amp
Mode
wed Jun 01 4:40
pm
1.
H
Ex
M
S
VOL
CH
OK
2.2.
SR9600U DFU_01_ENG 4_4 05.4.27, 5:47 PMPage 50 Adobe PageMaker 6.5J/PPC
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-9600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-9600 in the language / languages: English as an attachment in your email.

The manual is 10,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info