6604
37
Zoom out
Zoom in
Previous page
1/56
Next page
33
ENGLISH
BASS PEAK LEVEL
With Dolby Digital and DTS , not only the LFE (Low Frequency
Effects), but also the bass of all channels can be heard from the
Subwoofer or Large-speakers. This procedure prevents these
speakers from becoming too loud and creating an unbalanced sound.
Since the sound is output at a loud volume, perform this operation
carefully.
Note:
If your system does not include a subwoofer, this setting will set
the bass peak level for your front speakers.
TEST SIGNAL: Press the OK or Left button, START is indicated and
it begins to generate a Bass test tone from the
speaker which was designated “bass signal output”
during setup.
There will be no audible sound yet because the
Master volume is set to minimum automatically.
Press Down cursor button to move the cursor to
VOLUME control.
VOLUME: Adjust the bass test tone output level up until the
bass begins to distort or you reach the maximum
level with the VOL+, VOL– or Right / Left cursor
button.
Press Down cursor button to move the cursor to
ENTER.
ENTER: Press the OK button, ENTER will blink and stop
generating the Bass Peak test tone.
The Bass Peak Limit Level for your system has now
been memorized.
If you finish these setup, move cursor to “MAIN” with Up or Down
cursor button and then press OK button to go to MAIN menu.
Notes:
Each time the subwoofer level is changed, perform the Bass
Peak Level setup and correct the setting.
• The bass peak level is not available in SOURCE-DIRECT and
7.1CH-INPUT mode.
The selected value is displayed in the volume column before the
test signal starts.
2-4 BASS PEAK LEVEL
BASS PEAK TEST : START
VOLUME LEVEL : + 1 8dB
--------------------
ENTER
MA I N RE TURN E X I T
PREFERENCE
1.
Select “PREFERENCE” in MAIN SETUP MENU with Up or Down
cursor button, and press the OK button.
2.
To select a desired content, press Up or Down cursor button.
TV AUTO: Select the TV AUTO ON/OFF function to enable or
disable with Left or Right cursor button.
(refer to page 42)
OSD Info: Select the OSD information function to enable or
disable with Left or Right cursor button.
If you select “ENABLE”, SR8300 will display the status
of the feature (Volume up/down, input select, etc..) on
the TV monitor. But if you do not desire this
information, select “DISABLE “.
DIG. OUT: Select the digital source to output the DIGITAL OUT
terminals with Left or Right cursor button.
This is for digital dubbing to a CD-R recorder or MD
deck. (See page 43)
The source is switched in the following sequence.
SOURCE DIG.1 DIG.2 DIG.5 DIG.6
AUX OFF SOURCE
SUB-W OUT: “THX” position is required, but If you desire an
additional front L/R mixed subwoofer output in the
STEREO mode, select “L/R MIX” with Left or Right
button.
If you finish the setup in this item, move cursor to “MAIN” with Up or
Down cursor buttons and press OK button.
3PREFERENCE
TV-AUTO : DISABLE
OSD I NFO : ENABLE
DIGITAL OUT : SOURCE
SUBWOOFER OUT : THX
MA I N E X I T
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-8300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-8300 in the language / languages: English as an attachment in your email.

The manual is 5,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR-8300

Marantz SR-8300 User Manual - English - 57 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info