6588
64
Zoom out
Zoom in
Previous page
1/79
Next page
61
ENGLISH
LEARN MODE
Programming the
2
(PLAY) and Other Control But-
tons and Numeric Buttons
This remote control is capable of learning and storing
codes used by other remote controls that you already
own.
For codes which are not learned, the remote control
will transmit either the Marantz preset codes from
the initial settings, or remote codes from another
manufacturers AV equipment which is set by the
customer.
The receiver sensor for the remote control signals is
located at the top of the remote control.
This example shows how to learn the codes from the
remote control of a DVD player.
USE
PAG E
1
LEARN
PAG E
12
LEARN
12
1 2 4
LEARN
PAG E
12
LEARN
PAG E
12
6 (When OK) (failed) (codes are full)
12
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the D2 (LEARN) direct button.
The LEARN setting (LEARN) is displayed. The
LEARN
indicator then blinks.
3.
Press the DVD source button.
4.
Press the 2 (PLAY) button.
The
LEARN
indicator blinks, and then displays to
indicate that learning is ready.
5.
Place the receiver sensor of the remote control
(top) so that it is facing the transmitter of the
DVD remote control (top) at a distance of about
5 cm (2 inches).
6.
Press and hold down the 2 (PLAY) button of the
transmitting DVD remote control, and check that
OK is displayed on the LCD.
The remote control has fi nished learning when OK
is displayed on the LCD.
If ERROR is displayed on the LCD, some error has
prevented the command from being learned. If this
happens, repeat the procedure for steps 4 and 5.
In some rare cases, ERROR may be displayed
repeatedly during the learning operation. In this
case, the transmitting remote control may have
special signal codes. These codes cannot be
learned by this remote control.
7.
Follow the same procedure to make the remote
control learn the other buttons.
8.
Repeat the procedure in steps 3 to 6 to have
the remote control learn the signal codes from
a TV, CD player, or other AV equipment.
When no buttons are pressed for
approximately one minute during the
learning operation, the remote control
automatically returns to USE mode.
When programming the source buttons,
switch to the source in step 3, and then
press the source button again.
9. When you have finished programming the
codes for each button, press the M button.
The
USE
indicator is displayed on the LCD, and the
newly stored codes can be used.
If FULL is displayed on the LCD, the
memory cannot hold any more learned
codes in LEARN mode.
If FULL is displayed no matter how many
times you try the learning operation, the
remote control cannot accept any more new
codes until some of the previously learned
codes are deleted from the memory. Delete
some of the learned buttons from the
sources.
The M button and > button cannot be taught. Only
each one code can be learned for the LIGHT buttons
1 and 2, regardless of the source.
Programming the Direct Buttons and Rewriting
Names
This example shows how to program codes from
other manufacturer products to the DVD MENU
button (D1) and change the display to OSD.
LEARN
PAG E
12
LEARN
PAG E
12
6 7 8
LEARN
PAG E
12
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the D2 (LEARN) direct button.
The LEARN setting (LEARN) indicator is displayed.
The
LEARN
indicator then blinks.
3.
Press the DVD source button.
The first page of the direct button screen is
displayed. There are four available pages. Pressing
the > buttons cycles through the pages in this order
1
2
3
4
1.
4.
Press the D1 (MENU) direct button.
The
LEARN
indicator blinks, and then displays to
indicate that learning is ready.
5.
Place the receiver sensor of the remote control
(top) so that it is facing the transmitter of the
DVD remote control (top) at a distance of about
5 cm (2 inches).
6.
Press and hold down the OSD button of the
transmitting DVD remote control, and check that
OK is displayed on the LCD.
The remote control has fi nished learning when OK
is displayed on the LCD.
If ERROR is displayed on the LCD, some error has
prevented the command from being learned. If this
happens, repeat the procedure for steps 4 and 5.
After learning is completed, the remote
control automatically switches to name
rewriting mode. The left end “
” indicator
on the MENU blinks to indicate that the
blinking part can be rewritten.
If no names will be rewritten, press the
OK cursor button. The display returns to
learning standby mode by pressing the OK
cursor button.
7.
To change the name, press the numeric
buttonsto enter the text.
Use the cursor buttons 1 2 to move to the
sections to be rewritten on the LCD.
To change MENU to OSD, press the 5
numeric button.
Each time the button is pressed, the display
cycles through M N O 5 M.
8.
After rewriting of the text is completed, press
the OK cursor button.
To delete text that is already entered, press the
0
button to insert a space.
In this example, MENU is changed to “OSD
(space) (space)” in this step, and then OSD
is displayed in the right side by pressing the
OK button.
For details, refer to the section “Rewriting Names”.
9.
In the same way, use the > button to select
the page, and then press the direct button to
program the codes.
10.
After programming the codes for each of the
buttons, press the M button.
The
USE
indicator displays on the LCD, and the
newly stored codes can be transmitted.
REWRITING NAMES
This remote control allows the rewriting of names
for the sources and direct buttons. This operation is
performed for each individual source.
This example shows how to change the source name
from DVD to AVD and AUDIO to SOUND.
NAME
PAG E
12
3 4 5
LEARN
USE
PAG E
12
7 8 9
NAME
PAG E
12
NAME
PAG E
12
NAME
PAG E
12
NAME
PAG E
12
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the D3 (NAME) direct button .
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-8001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-8001 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info