6588

Marantz SR-8001 Manual

35
Zoom out
Zoom in
Previous page
1/79
Next page
ENGLISH
32
SUB W:
Set the distance from the subwoofer to your
normal listening position.
SURR. B L:
Set the distance from the surround back left
speaker to your normal listening position.
SURR. B R:
Set the distance from the surround back right
speaker to your normal listening position.
Notes:
• Set the distance to each speaker in meters (m) or feet
(ft) as follows.
m: 0.03 - 9.15 m in 0.03 m steps
ft: 0.1 - 30.0 ft in 0.1 ft steps
(The values appearing on the FL display are
approximate.)
• For the speakers that you have selected “NONE” the
speaker size menu will not appear.
• The setting for surr.back L and surr.back R appears
if it is set, two surround back speakers in the
SPEAKER SIZE menu.
• The setting of SURR. BACK appears if it is set for
one surround back speaker in the SPEAKER SIZE
menu.
11.
After you complete this portion of the setup,
move the cursor to “NEXT” with the 3, 4, 1 and
2 cursor buttons and press the OK/ENTER
button to go to the next page.
<SPEAKER LEVEL>
S PEAKER LEVEL
TES T MODE : MANUAL
FRONT L : 0.0dB
CENTER : 0.0dB
FRONT R : 0.0dB
S URR.R : 0.0dB
S URR.B R : 0.0dB
S URR.B L : 0.0dB
S URR.L : 0.0dB
S UB W : 0.0dB
RETURN BACK EXIT
Here you can set the volume for each speaker so
that they are all heard by the listener at the same
level. We recommend holding a dB SPL (Sound
Pressure Level) meter at the listening position, at
arms length, and pointing straight up at the ceiling,
adjust the level of each speaker in turn unit it reads
75dB SPL when the meter is set to “C” weighting and
Slow responce.
Note:
• The speaker level settings are not available in 7.1
Channel Input mode, Pure Direct mode and Source
Direct mode.
TEST MODE:
Select “MANUAL” or “AUTO” generation of the
test tone with the 1
or
2 cursor buttons.
If you select “AUTO”, the test tone will be cycled
through in a circular pattern beginning at Left →
Center → Right → Surround Right → Surround
Back Right → Surround Back Left → Surround
Left → Subwoofer → Left, in 2 seconds increments
for each channel.
Using the 1
or
2 cursor buttons, adjust the volume
level of the noise from the speaker so that it is the
same level for all the speakers.
If you select “MANUAL”, adjust the output level of
each speaker as listed below.
12.
Move the cursor to FRONT L by pressing the
4 cursor button. The SR7001 will emit a pink
noise from the front left speaker.
Remember the level of this noise and then
press the 4 cursor button.
(Note that this can be adjusted to any level
between -12 and +12 dB in 0.5 dB increments.)
The SR7001 will now emit the pink noise from
the center speaker.
13.
Using the 1 and 2 cursor buttons, adjust the
volume level of the noise from the center
speaker so that it is the same level as the front
left speaker.
14.
Press the 4 cursor button again. The SR7001
will now emit the pink noise from the front right
speaker.
15.
Repeat steps 13 and 14 for the front right and
other speakers until all speakers are adjusted
to the same volume level.
After you complete this portion of the setup, press the
OK/ENTER button to move the cursor to “RETURN”.
Press the OK/ENTER button to go to “2. SPKR
SETUP”.
Notes:
• Speakers for which you selected “NONE” in the
SPEAKER SIZE menu will not appear.
• Surr. Back L and Surr. Back R appear if it is set for
two surround back speakers in the SPEAKER SIZE
menu.
• Surr. Back appears if it is set for one surround back
speaker in the SPEAKER SIZE menu.
• To adjust the speaker levels for 7.1 channel input
sources, you will need to use the 7.1 Ch Input sub
menu. (See page 33)
• SUB W can be set from –18dB to +12dB.
2-3 THX AUDIO SETUP
You can set the advanced Speaker Array.
1.
Select “2. SPEAKER SETUP” from the MAIN
MENU.
2.
Select “THX AUDIO SETUP” with the 3
or
4
cursor buttons.
3.
Press the OK/ENTER button to enter the
selection.
THX AUDIO SETUP
ADVANCED SPKR ARRAY
SURR.B SPKR
:TOGETHER
RETURN EXIT
Advanced Speaker Array (ASA)
SURR.B SPKR: TOGETHER, CLOSE or APART
The best ASA effect is when the surround back
speakers are together and facing forward.
If the distance between the surround back speakers
is,
• Less than 12 in. (30 cm): TOGETHER
• Greater than 12 in. (30 cm), and less than 48 in.
(122 cm): CLOSE
• Greater than 48 in. (122 cm): APART
Speaker type and positioning
This diagram shows the desired positioning for 7.1
channel speaker systems used in ASA mode. During
system setup, select the distance between surround
back speakers.
FL
SBL SBR
C
FR
SL
SR
Surround B
Surround A
Surround-L Surround-R
Surround A
Di-polar Radiating Speaker
Direct Radiating Speaker
Front-L Center Front-R
Surround Back
LR
Note:
• If you set SURR.B = 1CH or NONE in the
SPEAKER SIZE menu, Advanced Speaker Array
will not be activated.
After you complete this portion of the setup, move
the cursor to “RETURN” with 3, 4, 1 and 2 cursor
buttons and press OK/ENTER button to go to the 2.
SPKR SETUP menu.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-8001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-8001 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info