6588
12
Zoom out
Zoom in
Previous page
1/79
Next page
ENGLISH
9
REMOTE CONTROLLER
RC8001SR
NAMES AND FUNCTIONS
z Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the
buttons while pointing the transmitter towards the
infrared receiver window of the SR7001 or other
AV equipment. Be sure to also point towards other
remote controls when using the learning function.
x POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the SR7001 on or
off.
c SOURCE ON/OFF button
This button is used to turn a specifi c source (such as
a DVD player) on or off independently from the rest
of the system.
v M (Mode) button
This button is used to program Macros. Pressing this
button switches between Normal mode and Macro
mode.
The > button is used to move to the next page. Up to
20 programs (4 pages) can be made. Holding down
the M button for three seconds or more switches to
the Setup mode, where the Setup menu is shown on
the LCD. The Setup menu has four pages, and the >
button is used to move to the next page. Pressing the
> button from page 4 returns you to page 1.
b D1 to D5 (Direct) buttons
Five types of direct operations can be performed
for each of the 12 source buttons such as the DVD,
television, amplifi er, and other AV equipment. The
pages can be switched, so 4 pages × 5 types = 20
operations can be performed for a single source. The
text display can also be changed.
n > (Page) button
This button is used to switch pages for the Direct
button. The current page is shown on the LCD.
m VOL (Volume) button
This button is used to adjust the volume for the
amplifi er and television.
Note:
Set the AMP mode to use this button with the
SR7001.
2 31
5 64
8
0
97
MEMO
CLEAR
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
SOURCE
OFF
ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP·SYNC
THX
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
12
LIGHT
Learning Remote Controller
RC8001SR
z
c
v
b
n
x
m
,
.
⁄1
⁄2⁄6
⁄7
⁄8
⁄9
¤0
¤1
⁄3
⁄4
⁄5
⁄0
@0 REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
@1 AUDIO IN/OUT (TV, DVD, VCR1,
DSS/VCR2, TAPE, CD/CDR)
These are the analog audio inputs and outputs. There
are 6 audio inputs (4 of which are linked to video
inputs) and 4 audio outputs (2 of which are linked to
video outputs). The audio jacks are nominally labeled
for cassette tape decks, compact disc players, DVD
players and etc.... The audio inputs and outputs
require RCA-type connectors.
@2 DIGITAL INPUT (Dig.1 - 6) /
OUTPUT (coaxial, optical)
These are the digital audio inputs and outputs. There
are 3 digital inputs with coaxial jacks, 3 with optical
jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other similar
components.
@3
VIDEO IN/OUT
(TV, DVD, VCR1, DSS/VCR2)
These are the video inputs and outputs. There
are 4 video inputs and 2 video outputs and each
one includes both composite video and S-video
confi gurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
@4 HDMI INPUT / OUTPUT
This unit has 4 HDMI inputs and 1 HDMI output. The
input function can be selected from the OSD menu
system. (See page 15) (The SR8001 has 2 HDMI
outputs.)
, MUTE button
This button is used to mute the audio for the SR7001
and television.
Note:
Set the AMP mode to use this button with the
SR7001.
. GUIDE button
This button is used to display the menus for the DVD
player, DSS (satellite broadcasting tuner), or other
AV equipment.
(when AMP mode is selected)
This button is used to select the LIP.SYNC mode.
⁄0 EXIT button
(when AMP mode is selected)
This button is used to cancel settings in the setup
menu.
⁄1 Numeric buttons
These buttons are used to switch between 0 to 9
of the source components. If the source is set to
the amplifier, these buttons are used to perform
operations.
(when AMP mode is selected)
(1) TEST button
Used to enter the test tone menu.
(2) CH SEL. (channel select) button
Used to call up SETUP MAIN MENU and adjust
speaker levels or 7.1 ch input level.
(3) SURR (surround) button
Used to select the surround mode.
(4) 7.1CH button
Press this button to select the output of an external multi
channel decoder.
(5) ATT button
When the input signal is too high and the voice
distorts even by throttling the SR7001 VOLUME
control, turn on this function. “ATT” is indicated when
this function is activated.
The input level is reduced. Attenuator is invalid for
use with the output signal of “REC OUT”.
Note:
This function is unavailable during the digital input
is selected.
(6) SPK-AB button
Speaker mode is switched in the following
sequence.
A B A+B off
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-8001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-8001 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info