6590

Marantz SR-7200 Manual

19
Zoom out
Zoom in
Previous page
1/39
Next page
12
ENGLISH
BASIC OPERATION
LISTENING TO THE TUNER
MANUAL TUNING
1. To select the tuner as the source, press the TUNER button t on
the front panel or press the TUNER button , on the remote
control unit.
2. Press the TUNER button t on the front panel or press the
TUNER button , on the remote control unit to select the desired
frequency band if required.
3. Press the F/P button !6 on the front panel to display the frequency.
4. Press the TUNING/PRESET or button !5 on the front panel or
press the ^, v button ⁄0 on the remote control unit.
5. If FM is selected, press the MODE button !7 on the front panel or
select T-MOD by the Jog Dial n and press the ENT button m in
the TUNER mode on the remote controller.
(FM) MODE BUTTON OPERATION
When “AUTO” indicator is on in the display, FM stations that broadcast
in stereo will be received in stereo and the “STEREO” indicator lights.
When “AUTO” indicator is off, all the FM stations will be received in
mono regardless of whether or not they are broadcasting in stereo.
AUTO TUNING
1. Press the F/P button !6 on the front panel to display the frequency.
2. Press the TUNING/PRESET or button !5 on the front panel
for more than 1 second to start the Auto tuning function.
AUTO TUNING (USING THE REMOTE CONTROL UNIT)
Press ^, v button ⁄0 for more than 1 second to start the Auto tuning
function.
PRESET TUNING
With this unit you can preset up to 30 FM/AM stations in any order. For
each station, you can memorize the frequency and reception mode if
desired.
1-a. Manual Presetting
1. Refer to the “MANUAL TUNING” or “AUTO TUNING” section
above to tune in a desired station.
2. Press the MEMORY button !4. “MEMORY” indicator starts blinking
on the display.
While “MEMORY” is still blinking (approx. 5 seconds), select the
preset number by pressing the TUNING/PRESET or button !5
then press the MEMORY button !4 again.
3. When a number has been properly input, “MEMORY” indicator
stops blinking and goes out.
The station is now stored in the specified preset memory location.
1-b. Manual Presetting (Using the remote unit)
1. Tune in a desired station.
2. Press the MEMO button ⁄6.
3. Enter the desired preset number with ten keypad ⁄7.
4. Then, press MEMO button ⁄6 again to store.
2. Auto Presetting
This function automatically scans the FM and AM band and enters all
stations with sufficient signal strength into the memory.
1. Press and hold down the MEMORY button !4 and TUNER button
t simultaneously for 3 seconds or more.
2. “MEMORY“ will blink on the display.
3. Each time the tuner finds a station, the scanning will pause and
memory. Auto presetting will starts.
4. Operation stops automatically when all 30 preset memory
positions are filled or when auto scanning attains the highest end
of all bands.
To stop the auto preset function at anytime, press the CLEAR
button !3.
3. Recalling a Preset Station
1. Press the F/P button !6 to change the display to preset.
2. Select the desired preset station by pressing TUNING/PRESET
or button !5 on the front panel or press CH or CH button ⁄2
on the remote.
Note:
To directly access the preset stations using the numeric keypad,
select the desired preset station by entering one or two digits using
the numeric keypad ⁄7.
To return to the Manual Tuning mode, press the F/P button !6.
4. Preset Scan Tuning (Using the remote control unit)
1. Select the SCAN by the Jog Dial n and press the ENT button m
in the TUNER mode on the remote controller. (The preset station
with the smallest preset number is recalled first. If no stations have
been preset, “NO PRESET” shows in the display and the unit
returns to the previous mode.)
2. Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5
seconds each. Preset numbers that do not contain stations are
skipped.
3. You can fast forward the preset stations by pressing the CH
button continuously.
When the desired preset station is received, cancel the preset scan
operation by pressing the CH button or the CLEAR button ⁄5.
5. Clearing Preset Stations
You can remove preset stations from memory using the following
procedure.
1. Recall the preset number to be cleared with the method described
in “Recalling” a preset station.
2. Press the CLEAR button !3 on the front panel or CLEAR button
⁄5 on the remote control unit for 3 seconds or more.
“CLEAR” appears on the display to indicate that the specified
preset number has been cleared.
6. Frequency Direct Call
1. Select F-DIR by the Jog Dial n and press the ENT button m in
the TUNER mode on the remote controller.
2. Display shows “FM– – –.––MHz” (at FM mode).
3. Input your desired frequency with tenkeypad buttons on the
remote controller.
Eg) 98.1 MHz
Press 9, 8, 1 and 0
4. Press the ENT button m again.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-7200 in the language / languages: English as an attachment in your email.

The manual is 3,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR-7200

Marantz SR-7200 User Manual - English - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info